Other uses were already used direct command paths.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Powersave looks like it got broken at some point but we'll fix that up
when the command submission stuff is more understandable, which this
series helps to do. That said, this patch should not further break
powersave.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Slightly different approach here since there are so many arguments to
the firmware command. Just let the caller fill them in before pushing
the command to the firmware.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For now; it's a pretty easy command to hook up and whenever OLPC
figures out how they want the userspace interface to look (ie,
not iwpriv commands) we can easily add it back in. Since the
cfg80211 conversion it wasn't working anyway.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It hasn't been hooked up to anything in a long time and it's not
even listed in any of the firmware documentation I have (and I
have v5.1, v8, v9, and v10).
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These were no longer used but were left around; Transmit Power
Control is done through the lbs_set_tpc_cfg() function.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert to a full direct command; previous code rolled a direct
command by hand but left the original indirect command code intact
but disabled.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert to a full direct command; previous code rolled a direct
command by handle but left the original indirect command code
lying around.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On our hardware (050d:7050 Belkin Components F5D7050 Wireless G Adapter),
setting any WEP key with non zero index, cause rx frames corruption.
Note: perhaps (I did not check) this can be fixed differently - by using
hw_key_idx the same as true MAC key index. But according to the comment in
rt2x00mac_set_key():
"the hardware requires keys to be assigned in correct order (When key 1
is provided but key 0 is not, then the key is not found by the hardware
during RX)"
this will be quite problematic. Since WEP should not be used, disabling
hardware crypto offload for it will not hurt much. Beside static
one key WEP will still be offloaded.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Without cipher part nullify of TXRX_CSR0 register we can receive
corrupted frames (removed IV or IVC), after reloading rt2500usb module
with nohwcrypt=1 option, if previous some keys were configured into
the hardware.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix rt2500usb hardware encryption broken by commit
96b61bafe2
"rt2x00: Clean up USB vendor request buffer functions"
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The user ratekbs of MCS15 ShortGI is incorrect and can not be lesser
than MCS15 rate. This incorrect rate may affect switching to higher
rates as the rate control algorithm always finds MCS15 is better
than MCS15 ShortGI and results in lower throughput. Fix this by
feeding the correct user ratekbs for MCS15 ShortGI rate.
This issue affects 3 stream case very badly as the 3 stream rates are
not used at all once we scale down to MCS15 from 3 stream rates.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds 3 stream rate control support for AR938X family
chipsets which supports 3 streams.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
replace valid and valid_single_stream in rate table with bit masks
and reorganize the code so adding 3x3 rate control would be easier.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since commit:
commit f1aa4c541e
Author: Ivo van Doorn <ivdoorn@gmail.com>
Date: Tue Jun 29 21:38:55 2010 +0200
rt2x00: Write the BSSID to register when interface is added
mananged mode in rt2500pci was broken, due to intf->bssid containing
random data rather then the expected 00:00:00:00:00:00
This is corrected by sending the BSSID to rt2x00lib_config_intf
only in AP mode where the bssid is set to a valid value.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The noisefloor array index always corresponds to the rx chain number it
belongs to (with an offset of 3 for the extension chain).
It's much simpler (and actually more correct) to directly use the
chainmask to calculate the bitmask for the noisefloor array, instead of
using these weird chip revision checks and hardcoded mask values.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Williams
Stanislaw Gruszka
Senthil Balasubramanian
John W. Linville
Ivo van Doorn
Felix Fietkau