Palmas driver is used to cater to even TPS659038 but TPS659038 does not have
REGEN3 resource. Adding another field in the driver data to check on that.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The register offset for REGEN2_CTRL in different for TPS659038 chip as when
compared with other Palmas family PMICs. In the case of TPS659038 the wrong
offset pointed to PLLEN_CTRL and was causing a hang. Correcting the same.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
These of_node_get() were added to balance refcount decrements inside of
of_find_node_by_name().
See: commit c92f5dd2c4 ("regulator: Add missing of_node_put()")
However of_find_node_by_name() was then replaced by of_get_child_by_name(),
which doesn't call of_node_put() against its input parameter.
So, need to remove these unnecessary of_node_get() calls.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We use regmap regulator ops to enable/disable and check if regulator
is enabled for various SMPS. However, these depend on valid
enable_reg, enable_mask and enable_value in regulator descriptor.
So, similar to fix we did in commit 318dbb02b5
("regulator: palmas: Fix SMPS enable/disable/is_enabled"), populate the
same for TPS65917 SMPS registration. LDO definitions are already in
place.
Fixes: d6f83370ed ("regulator: palmas: Add tps65917 PMIC support")
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Palmas regulator needs to full up the regulator_desc based on PMIC and
type of regulator. However, we dont need to do desc[id] every time. we
can simplify by using a pointer to desc[id] and filling up the
parameters.
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
With commit d6f83370ed (regulator: palmas:
Add tps65917 PMIC support) palmas_regs_info naming is confusing as it is
a driver data parameter and a local variable. To prevent mistaken
updates, rename the local variable to palmas_generic_regs_info.
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Palmas register information is part of the ddata pointer which is used
through out the code by indexing off the driver data array. Instead,
just do the indexing once and use the pointer to further reference
structure fields.
This simplifies code and prevents errors by accessing wrong variables.
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
reg_info is a generic term which might cause conflict at a later point
in time. To prevent such a thing from occuring in future, rename to
palmas_reg_info.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
convert to static variables to squelch the following sparse warnings:
drivers/regulator/palmas-regulator.c:325:36: warning: symbol 'palma_sleep_req_info' was not declared. Should it be static?
drivers/regulator/palmas-regulator.c:1414:32: warning: symbol 'palmas_ddata' was not declared. Should it be static?
drivers/regulator/palmas-regulator.c:1427:32: warning: symbol 'tps65917_ddata' was not declared. Should it be static?
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
When setting up .enable_reg for an SMPS regulator, presumably we should
call PALMAS_BASE_TO_REG(PALMAS_SMPS_BASE, ...) rather than using
LDO_BASE. This change makes the LCD panel and HDMI work again on the
NVIDIA Dalmore board anyway.
Fixes: 318dbb02b5 ("regulator: palmas: Fix SMPS enable/disable/is_enabled")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Nishanth Menon <nm@ti.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
We use regmap regulator ops to enable/disable and check if regulator
is enabled for various SMPS. However, these depend on valid
enable_reg, enable_mask and enable_value in regulator descriptor.
Currently we do not populate these for SMPS other than SMPS10, this
results in spurious results as regmap assumes that the values are
valid and ends up reading register 0x0 RTC:SECONDS_REG on Palmas
variants that do have RTC! To fix this, we update proper parameters
for the descriptor fields.
Further, we want to ensure the behavior consistent with logic
prior to commit dbabd624d4, where, once you do a set_mode,
enable/disable ensure the logic remains consistent and configures
Palmas to the configuration that we set with set_mode (since the
configuration register is common). To do this, we can rely on the
regulator core's regulator_register behavior where the regulator
descriptor pointer provided by the regulator driver is stored. (no
reallocation and copy is done). This lets us update the enable_value
post registration, to remain consistent with the mode we configure as
part of set_mode.
Fixes: dbabd624d4 ("regulator: palmas: Reemove open coded functions with helper functions")
Reported-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
get_voltage_sel reads from SMPS register - if the read selector value
is 0, the SMPS is actually disabled - So, this is in addition to the
ctrl_register that may also be used to enable/disable the SMPS.
The original logic(prior to commit dbabd624d4) used to be:
static int palmas_map_voltage_smps(struct regulator_dev *rdev,
int min_uV, int max_uV)
<snip>
if (min_uV == 0)
return 0;
To handle this scenario, with the transition to regulator_list
implementation, we seem to have missed the data necessary to mark as
one of the valid entries as "0" 'disabled regulator' which results in
0 volts - So, stick with pre-existing logic.
Without this added to the list, palmas regulator driver,
on probe, attempts to setup constraints and in the case of
OMAP5uEVM, SMPS9 (which is mapped for 2v1 audio supply) fails in
regulator_list_voltage_linear_range mapping of '0', and as a fall back
of constraints not being applied, the entire regulator list is not
enumerated due to assumption that something system wide has gone bad
on with the PMIC.
Fixes: dbabd624d4 ("regulator: palmas: Reemove open coded functions with helper functions")
Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The device tree binding of Palmas regulator driver says as:
palmas_pmis {
compatible = "ti,palmas-pmic";
...
regulators {
...
}
};
In this "regulators" subnode is expected to be part of parent node, not
the outside of parent node. Hence to get the regulator node, the correct
call is of_get_child_by_name() rather than of_find_node_by_name() which
actually searches the "regulators" node from the parent node to end of DTS
file.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Keerthy
Mark Brown
Fabian Frederick
Wolfram Sang
Guodong Xu
Nishanth Menon
Mark Brown
Stephen Warren
Jingoo Han
Laxman Dewangan