The statistics for InputMegabytes and OutputMegabytes are
misnamed. They're accumulating bytes, not megabytes.
The statistic returned via /sys must be in megabytes, however,
which is what the HBA-API wants. The FCP code needs to accumulate
it in bytes and then divide by 1,000,000 (not 2^20) before it
presented via sysfs.
This affects fcoe.ko only, not fnic. The fnic driver
correctly by accumulating bytes and then converts to megabytes.
I checked that libhbalinux is using the /sys file directly without
conversion.
BTW, qla2xxx does divide by 2^20, which I'm not fixing here.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Should not continue when the abort itself is being timeout since in that case
the exchange will be deleted and relesased. We still want to call the
associated response handler to let the layer, e.g., fcp, know the exchange
itself is being timed out.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Do not call fc_io_compl() on fsp w/o any scsi_cmnd, e.g., lun reset is built
inside fc_fcp, not from a scsi command from queuecommnd from scsi-ml, so in
in case target is buggy that is invalid flags in the FCP_RSP, as we have seen
in some SAN Blaze target where all bits in flags are 0, we do not want to call
io_compl on this fsp.
[ Comment block added by Robert Love ]
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This is very helpful to match up the corresponding exchange to the actual I/O
described by the fsp, particularly when you do a side-by-side comparison of
the syslog with your trace.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Use the rport value for rec_tov for timeout values when
sending fcp commands. Currently, defaults are being used
which may or may not match the advertised values.
The default may cause i/o to timeout on networks that
set this value larger then the default value. To make
the timeout more configurable in the non-REC mode we
remove the FC_SCSI_ER_TIMEOUT completely allowing the
scsi-ml to do the timeout. This removes an unneeded
timer and allows the i/o timeout to be configured
using the scsi-ml knobs.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The fcp packet recovery handler fc_fcp_recover() is called
when errors occurr in a fcp session. Currently it is
generically setting the status code to FC_CMD_RECOVERY for
all error types. This results in DID_BUS_BUSY errors
being returned to the scsi-ml.
DID_BUS_BUSY errors indicate "BUS stayed busy through time
out period" according to scsi.h. Many of the error reported
by fc_rcp_recovery() are pkt errors. Here we update
fc_fcp_recovery to use better host byte codes.
With certain FAST FAIL flags set DID_BUS_BUSY and DID_ERROR
will have different behaviors this was causing dm multipath
to fail quickly in some cases where a retry would be a
better action.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The error handler grabs the si->scsi_queue_lock, but
in the case where the fsp pointer is NULL it releases
the scsi_host lock. This can lead to a variety of
system hangs depending on which is used first- the
scsi_host lock or the scsi_queue_lock.
This patch simply unlocks the correct lock when fcp
is NULL.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
For allocating new exch from pool, scanning for free slot in exch
array fluctuates when exch pool is close to exhaustion.
The fluctuation is smoothed, and the scan looks to be O(2).
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Move the mid-layer's ->queuecommand() invocation from being locked
with the host lock to being unlocked to facilitate speeding up the
critical path for drivers who don't need this lock taken anyway.
The patch below presents a simple SCSI host lock push-down as an
equivalent transformation. No locking or other behavior should change
with this patch. All existing bugs and locking orders are preserved.
Additionally, add one parameter to queuecommand,
struct Scsi_Host *
and remove one parameter from queuecommand,
void (*done)(struct scsi_cmnd *)
Scsi_Host* is a convenient pointer that most host drivers need anyway,
and 'done' is redundant to struct scsi_cmnd->scsi_done.
Minimal code disturbance was attempted with this change. Most drivers
needed only two one-line modifications for their host lock push-down.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When number of NPIV ports created are greater than the xids
allocated per pool -- for eg., creating 255 NPIV ports on a
system with nr_cpu_ids of 32, with each pool containing 128
xids -- and then generating a link event - for eg.,
shutdown/no shutdown -- on the switch port causes the hang
with the following stack trace.
Call Trace:
schedule_timeout+0x19d/0x230
wait_for_common+0xc0/0x170
__cancel_work_timer+0xcf/0x1b0
fc_disc_stop+0x16/0x30 [libfc]
fc_lport_reset_locked+0x47/0x90 [libfc]
fc_lport_enter_reset+0x67/0xe0 [libfc]
fc_lport_disc_callback+0xbc/0xe0 [libfc]
fc_disc_done+0xa8/0xf0 [libfc]
fc_disc_timeout+0x29/0x40 [libfc]
run_workqueue+0xb8/0x140
worker_thread+0x96/0x110
kthread+0x96/0xa0
child_rip+0xa/0x20
Fix is to not cancel the disc_work if discovery is already
stopped, thus allowing lport state machine to restart and try
discovery again.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Acked-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
It is unlikely but in case if it hits then it would cause panic
due to null cmd ptr, so far only one instance seen recently with
ESX though this was introduced long ago with this commit:-
commit c1ecb90a66
Author: Chris Leech <christopher.leech@intel.com>
Date: Thu Dec 10 09:59:26 2009 -0800
[SCSI] libfc: reduce hold time on SCSI host lock
Currently fsp->cmd is set to NULL w/o scsi_queue_lock before
dequeuing from scsi_pkt_queue and that could cause NULL
fsp->cmd in fc_fcp_cleanup_each_cmd for cmd completing
with fsp->cmd = NULL after fc_fcp_cleanup_each_cmd taken
reference. No need to set fsp->cmd to NULL as this is also
protected by fc_fcp_lock_pkt(), for above race the
fc_fcp_lock_pkt() in fc_fcp_cleanup_each_cmd() will fail
as that cmd is already done.
Mike mentioned same issue at
http://www.open-fcoe.org/pipermail/devel/2010-September/010533.html
Similarly moved sc_cmd->SCp.ptr = NULL under scsi_queue_lock so
that scsi abort error handler won't abort on completed cmds.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Sometimes switch in NPV mode rejects flogi request with DID
zero and in that case flogi is not tried again and port
remains offline, so this patch validates DID for non zero
along with only ACC response to allow flogi retry
for RJT with DID=0 also succeed FLOGI in next try.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
There does not seem to be a reason why libfc adds a 5
second delay to the user requested value for the dev loss
tmo. There also does not seem to be a reason to allow
setting it to 0 (or really close).
This patch removes the extra 5 sec delay, and for 0 it
sets it to 1 like other fc drivers. We should actually
be able to set it to 0 since the queue_delayed_work API
will just call queue_work, but other drivers set it to 1 in
that case.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Joe Eykholt
Yi Zou
Hillf Danton
john fastabend
Robert Love
Jeff Garzik
Uwe Kleine-König
Bhanu Prakash Gollapudi
Vasu Dev
Mike Christie