* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (33 commits)
usb: don't use flush_scheduled_work()
speedtch: don't abuse struct delayed_work
media/video: don't use flush_scheduled_work()
media/video: explicitly flush request_module work
ioc4: use static work_struct for ioc4_load_modules()
init: don't call flush_scheduled_work() from do_initcalls()
s390: don't use flush_scheduled_work()
rtc: don't use flush_scheduled_work()
mmc: update workqueue usages
mfd: update workqueue usages
dvb: don't use flush_scheduled_work()
leds-wm8350: don't use flush_scheduled_work()
mISDN: don't use flush_scheduled_work()
macintosh/ams: don't use flush_scheduled_work()
vmwgfx: don't use flush_scheduled_work()
tpm: don't use flush_scheduled_work()
sonypi: don't use flush_scheduled_work()
hvsi: don't use flush_scheduled_work()
xen: don't use flush_scheduled_work()
gdrom: don't use flush_scheduled_work()
...
Fixed up trivial conflict in drivers/media/video/bt8xx/bttv-input.c
as per Tejun.
To inject a packet in monitor mode, a dummy station has
to be associated with the monitor interface in the target.
Failing to do this would result in a firmware crash on the device.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath5k_eeprom_mode_from_channel() returns -1 on error but we're storing
the result in "ee_mode" which is an unsigned char. This breaks the
error handling. This patch makes "ee_mode" an int.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove some obvious looking dead code and rename few functions
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Restart the beacon timers only if the beacon
was already configured. Otherwise beacons timers
are restarted unnecessarily in unassociated state too.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 0ce3bcfc84.
Event though with the above commit we obtain the configured DTIM period
from the AP rather than always hardcoding it to '1', this seems to cause
problems under the following scenarios:
* Preventing association with broken AP's
* Adds latency in roaming
So its better to always use the safe value of '1' for dtim period
Cc: Jouni Malinen <Jouni.Malinen@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
An Rx DMA descriptor can have multiple error bits set, and some error
bits (e.g. MIC failure) are filtered by the driver based on other criteria.
Remove the 'else' in various error bit checks so that all error information
is properly passed to the driver.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When returning to the operating channel, a full HW
reset has to be done instead of a fast channel change.
Since sw_scan_complete() is called after the config() call for the
home channel, we end up doing a FCC. Fix this issue by checking
the OFFCHANNEL flag to determine FCC.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The device has to be reset when a FATAL event is received.
Not doing so would leave the card in a non-working state.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to lock the various work cancellation
calls. This will be helpful when handling FATAL events.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When doing a channel change, the pending URBs have to be killed
properly on calling htc_stop().
This fixes the probe response timeout seen when sending UDP traffic at
a high rate and running background scan at the same time.
Cc: stable <stable@kernel.org>
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some minor clean ups in assigning values to beacon config parameters
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The tx desciptor already gets initialized to 0. Hence, there's no need
to explicitly assign 0 to mpdu_density here.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Backtrace:
rt2800usb_write_tx_data
rt2x00queue_write_tx_frame
rt2x00mac_tx
invoke_tx_handlers
__ieee80211_tx
ieee80211_tx
virt_to_head_page
ieee80211_xmit
ieee80211_tx_skb
ieee80211_scan_work
schedule
ieee80211_scan_work
process_one_work
...
It tried to expand the skb past it's end using skb_put. So I replaced it
with a call to skb_padto, which takes the issue into account.
Signed-off-by: Ismael Luceno <ismael.luceno@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Linus Torvalds
John W. Linville
roel kluin
Sujith Manoharan
Dan Carpenter
Mohammed Shafi Shajakhan
Rajkumar Manoharan
Felix Fietkau
Helmut Schaa
Ismael Luceno