hdc100x supports Texas Instruments HDC1000 and HDC1008 relative
humidity and temperature sensors. Add these product names to
Kconfig.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Replace the i2c_smbus_read_byte commmands used to retrieve the sensor
data with an i2c_master_recv command.
The smbus read byte method fails because the device does not expect a
stop condition after sending the first byte. When we issue the second
read, we are getting the first byte again. Net effect is that of the 14
bits used for the measurement, the 8 most significant bits are correct,
the lower 6 are not.
None of the smbus read protocols follow the pattern this device requires
(S Addr Rd [A] Data [A] Data NA P), hence the switch to an i2c receive
transaction.
Applicable from original introduction of this driver, but will require
backporting due to churn in the code.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Select IIO_BUFFER and IIO_TRIGGERED_BUFFER to compile.
Remove IIO_TRIGGER if present since IIO_BUFFER selects it.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We want the fixes in here, and we can resolve a merge issue in
drivers/iio/industrialio-trigger.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
IIO_TEMP channel was being incorrectly reported back as Celsius when it
should have been milliCelsius. This is via an incorrect scale value being
returned to userspace.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The I2C drivers have an i2c_device_id array but that information isn't
exported to the modules using the MODULE_DEVICE_TABLE() macro. So the
modules autoloading won't work if the I2C device is registered using
OF or legacy board files due missing alias information in the modules.
The issue was found using Kieran Bingham's coccinelle semantic patch:
https://lkml.org/lkml/2016/5/10/520
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Apply the correct mask to enable all available humidity integration
times. Currently, the driver defaults to 6500 and all is okay with that.
However, if 3850 is selected we get a stuck bit and can't change back
to 6500 or select 2500. (Verified with HDC1008)
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Reviewed-by: Matt Ranostay <mranostay@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
* Unify log messages
* Add more DEBUG messages
Apparently this driver is working unreliably on some platforms that I can't
test. Therefore I want an easy way for bug reporters to provide useful
information without making the driver too chatty by default.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Previously most drivers that used a i2c_check_functionality() check
condition required various error codes on failure. This patchset
converts to a standard of -EOPNOTSUPP
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Wall time obtained from ktime_get_real_ns is susceptible to sudden jumps due to
user setting the time or due to NTP. Boot time is constantly increasing time
better suited for comparing two timestamps.
Signed-off-by: Abhilash Jindal <klock.android@gmail.com>
Reviewed-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The new algorithm uses a 'one size fits em all' threshold, which should
be easier to understand and debug. I believe there are no regressions
compared to the old adaptive threshold algorithm. I don't remember why
I chose the old algorithm when I initially wrote the driver.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Instead of guessing where the data starts, we now just try to decode from
every possible start position. This causes no additional overhead if we
properly received the full preamble and only costs a few extra CPU cycles
in the case where the preamble is corrupted. This is much more efficient
than to return an error to userspace and start over again.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Jonathan writes:
First set of IIO fixes for the 4.4 cycle.
This set does not include those for issues introduced during the merge
window. Fixes of those will follow in a future series.
* ad5064
- Make sure the local i2c_write returns 0 on success rather than the
number of bytes transfered. Otherwise we report an error on all writes.
- Fix a shift for ad5629 and ad5669 which gives incorrect DAC output on
these parts.
* ad7793
- The product ID on the datasheet is wrong. Fix it in the driver.
* IIO_DUMMY_EVGEN
- select IRQ_WORK as a dependency.
* lpc32xx
- make sure clock is prepared before enabling.
* si7020
- data byte order was reversed. Fix it.
* vf610
- Internal temperature calculation was wrong if a different
reference voltage was used. Now use a linear interpolation
function to make it work over the full range.
- Fix a division by zero in the case of a device tree property
not being present (same issue two fixes).
* xilinx XADC
- VREFN scale was wrong - fix it.
The Silicon Labs Si7013, Si7020, and Si7021 family of I2C humidity and
temperature sensors deliver 16 bit data high byte first.
See the datasheet available at:
https://www.silabs.com/Support%20Documents%2fTechnicalDocs%2fSi7020-A20.pdf
But as documented in Documentation/i2c/smbus-protocol,
i2c_smbus_read_word_data() expects the low byte first.
Change the driver to use i2c_smbus_read_word_swapped to get correct byte
order.
Signed-off-by: Chris Lesiak <chris.lesiak@licor.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Previous offset wasn't applied in the correct order and invalid.
This patchset fixes this issue, and also has the correct scale value
applied to the offset.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Support for MS8607 temperature, pressure & humidity sensor.
This part is using functions from MS5637 for temperature and pressure
and HTU21 for humidity
Signed-off-by: Ludovic Tancerel <ludovic.tancerel@maplehightech.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Greg Kroah-Hartman
Alison Schofield
Matt Ranostay
Javier Martinez Canillas
Dan Carpenter
Tiberiu Breana
Harald Geyer
Abhilash Jindal
Cristina Moraru
Chris Lesiak
Ludovic Tancerel