SuperH fixes for 3.3-rc5
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh:
sh: Fix sh2a build error for CONFIG_CACHE_WRITETHROUGH
sh: modify a resource of sh_eth_giga1_resources in board-sh7757lcr
arch/sh: remove references to cpu_*_map.
sh: Fix typo in pci-sh7780.c
sh: add platform_device for SPI1 in setup-sh7757
sh: modify resource for SPI0 in setup-sh7757
sh: se7724: fix compile breakage
sh: clkfwk: bugfix: use clk_reparent() for div6 clocks
sh: clock-sh7724: fixup sh_fsi clock settings
sh: sh7757lcr: update to the new MMCIF DMA configuration
sh: fix the sh_mmcif_plat_data in board-sh7757lcr
video: pvr2fb: Fix up spurious section mismatch warnings.
sh: Defer to asm-generic/device.h.
fbdev fixes for 3.3
It includes:
- compile fix for fsl-diu-fb
- fix for a suspend/resume issue in atmel_lcdfb
- fix for a suspend/resume issue in OMAP
- workaround for a hardware bug to avoid physical damage in OMAP
- really trivial dead code removal in intelfb
* tag 'fbdev-fixes-for-3.3-1' of git://github.com/schandinat/linux-2.6:
atmel_lcdfb: fix usage of CONTRAST_CTR in suspend/resume
intelfb: remove some dead code
drivers/video: compile fixes for fsl-diu-fb.c
OMAPDSS: HDMI: PHY burnout fix
OMAP: 4430SDP/Panda: add HDMI HPD gpio
OMAP: 4430SDP/Panda: setup HDMI GPIO muxes
OMAPDSS: remove wrong HDMI HPD muxing
OMAP: 4430SDP/Panda: rename HPD GPIO to CT_CP_HPD
OMAP: 4430SDP/Panda: use gpio_free_array to free HDMI gpios
OMAPDSS: use sync versions of pm_runtime_put
The goto on the line before means the return is unreachable. The goto
also returns -ENODEV so no changes are needed there.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Fix assembler constraint to prevent overeager gcc optimisation
mac_esp: rename irq
mac_scsi: dont enable mac_scsi irq before requesting it
macfb: fix black and white modes
m68k/irq: Remove obsolete IRQ_FLG_* definitions
Fix up trivial conflict in arch/m68k/kernel/process_mm.c as per Geert.
A hardware bug in the OMAP4 HDMI PHY causes physical damage to the board
if the HDMI PHY is kept powered on when the cable is not connected.
This patch solves the problem by adding hot-plug-detection into the HDMI
IP driver. This is not a real HPD support in the sense that nobody else
than the IP driver gets to know about the HPD events, but is only meant
to fix the HW bug.
The strategy is simple: If the display device is turned off by the user,
the PHY power is set to OFF. When the display device is turned on by the
user, the PHY power is set either to LDOON or TXON, depending on whether
the HDMI cable is connected.
The reason to avoid PHY OFF when the display device is on, but the cable
is disconnected, is that when the PHY is turned OFF, the HDMI IP is not
"ticking" and thus the DISPC does not receive pixel clock from the HDMI
IP. This would, for example, prevent any VSYNCs from happening, and
would thus affect the users of omapdss. By using LDOON when the cable is
disconnected we'll avoid the HW bug, but keep the HDMI working as usual
from the user's point of view.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapdss doesn't work properly on system suspend. The problem seems to be
the fact that omapdss uses pm_runtime_put() functions when turning off
the hardware, and when system suspend is in process only sync versions
are allowed.
Using non-sync versions normally and sync versions when suspending would
need rather ugly hacks to convey the information of
suspending/not-suspending to different functions. Optimally the driver
wouldn't even need to care about this, and the PM layer would handle
syncing when suspend is in process.
This patch changes all omapdss's pm_runtime_put calls to
pm_runtime_put_sync. This fixes the suspend problem, and probably the
performance penalty of always using sync versions is negligible.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
macfb won't init in black & white modes since fb_alloc_cmap() no longer
works for zero cmap length. Fix this and also clean up a few printk's and
some stylistic inconsistencies.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
* 'fbdev-next' of git://github.com/schandinat/linux-2.6: (175 commits)
module_param: make bool parameters really bool (drivers/video/i810)
Revert "atmel_lcdfb: Adjust HFP calculation so it matches the manual."
OMAPDSS: HDMI: Disable DDC internal pull up
OMAPDSS: HDMI: Move duplicate code from boardfile
OMAPDSS: add OrtusTech COM43H4M10XTC display support
OMAP: DSS2: Support for UMSH-8173MD TFT panel
ASoC: OMAP: HDMI: Move HDMI codec trigger function to generic HDMI driver
OMAPDSS: HDMI: Create function to enable HDMI audio
ASoC: OMAP: HDMI: Correct signature of ASoC functions
ASoC: OMAP: HDMI: Introduce driver data for audio codec
grvga: fix section mismatch warnings
video: s3c-fb: Don't keep device runtime active when open
video: s3c-fb: Hold runtime PM references when touching registers
video: s3c-fb: Take a runtime PM reference when unblanked
video: s3c-fb: Disable runtime PM in error paths from probe
video: s3c-fb: Use s3c_fb_enable() to enable the framebuffer
video: s3c-fb: Make runtime PM functional again
drivers/video: fsl-diu-fb: merge fsl_diu_alloc() into map_video_memory()
drivers/video: fsl-diu-fb: add default platform ops functions
drivers/video: fsl-diu-fb: remove broken reference count enabling the display
...
Autogenerated GPG tag for Rusty D1ADB8F1: 15EE 8D6C AB0E 7F0C F999 BFCB D920 0E6C D1AD B8F1
* tag 'for-linus' of git://github.com/rustyrussell/linux:
module_param: check that bool parameters really are bool.
intelfbdrv.c: bailearly is an int module_param
paride/pcd: fix bool verbose module parameter.
module_param: make bool parameters really bool (drivers & misc)
module_param: make bool parameters really bool (arch)
module_param: make bool parameters really bool (core code)
kernel/async: remove redundant declaration.
printk: fix unnecessary module_param_name.
lirc_parallel: fix module parameter description.
module_param: avoid bool abuse, add bint for special cases.
module_param: check type correctness for module_param_array
modpost: use linker section to generate table.
modpost: use a table rather than a giant if/else statement.
modules: sysfs - export: taint, coresize, initsize
kernel/params: replace DEBUGP with pr_debug
module: replace DEBUGP with pr_debug
module: struct module_ref should contains long fields
module: Fix performance regression on modules with large symbol tables
module: Add comments describing how the "strmap" logic works
Fix up conflicts in scripts/mod/file2alias.c due to the new linker-
generated table approach to adding __mod_*_device_table entries. The
ARM sa11x0 mcp bus needed to be converted to that too.
pvr2fb special cases its init/exit routines which causes spurious section
mismatches. Set the board_driver array __refdata to silence them.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Dan Carpenter points out that it's an int, not a bool:
intelfbdrv.c:818: if (bailearly == 1)
intelfbdrv.c:828: if (bailearly == 2)
intelfbdrv.c:836: if (bailearly == 3)
intelfbdrv.c:842: if (bailearly == 4)
intelfbdrv.c:851: if (bailearly == 5)
intelfbdrv.c:859: if (bailearly == 6)
intelfbdrv.c:866: bailearly > 6 ? bailearly - 6 : 0);
intelfbdrv.c:874: if (bailearly == 18)
intelfbdrv.c:886: if (bailearly == 19)
intelfbdrv.c:893: if (bailearly == 20)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This reverts commit 5d910426a6.
Nicolas Ferre <nicolas.ferre@atmel.com> wrote:
"Unfortunately this is not true for all the SoC that embed the
atmel_lcdfb... So I may need to rework this patch but it is certainly
not applicable in the current form."
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Linus Torvalds
Russell King
Hubert Feurstein
Dan Carpenter
Florian Tobias Schandinat
Michael Neuling
Paul Mundt
Tomi Valkeinen
Axel Lin
Finn Thain
Andrew Morton
Rusty Russell