Bosch M_CAN is CAN FD capable device. This patch implements the CAN
FD features include up to 64 bytes payload and bitrate switch function.
1) Change the Rx FIFO and Tx Buffer to 64 bytes for support CAN FD
up to 64 bytes payload. It's backward compatible with old 8 bytes
normal CAN frame.
2) Allocate can frame or canfd frame based on EDL bit
3) Bitrate Switch function is disabled by default and will be enabled
according to CANFD_BRS bit in cf->flags.
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The spec mentions there may be a delay until the value written to INIT can be
read back due to the synchronization mechanism between the two clock domains.
But it does not indicate the exact clock cycles needed. The 5us delay is a
test value and seems ok.
Without the delay, CCCR.CCE bit may fail to be set and then the initialization
fail sometimes when do repeatly up and down.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The original code missed to set the cf->can_dlc in the RTR case, so add it.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The M_CAN message RAM is usually equipped with a parity or ECC functionality.
But RAM cells suffer a hardware reset and can therefore hold arbitrary content
at startup - including parity and/or ECC bits.
To prevent the M_CAN controller detecting checksum errors when reading
potentially uninitialized TX message RAM content to transmit CAN frames the TX
message RAM has to be written with (any kind of) initial data.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
m_can uses io memory which makes it not compilable on architectures
without HAS_IOMEM such as UML:
drivers/built-in.o: In function `m_can_plat_probe':
m_can.c:(.text+0x218cc5): undefined reference to `devm_ioremap_resource'
m_can.c:(.text+0x218df9): undefined reference to `devm_ioremap'
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The variable err was of the type u32. It was being compared with < 0, and being
an unsigned variable the comparison would have been always false.
Moreover, err was getting the return value from set_reset_mode() and
xcan_set_bittiming(), and both are returning int.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
these variable were only assigned some values, but then never
reused again.
so they are safe to be removed.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
It seems struct esd_usb2 dev is not deallocated on disconnect. The patch adds
the missing deallocation.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes a typo in CAN's dev.c:
CIA -> CiA
which stands for CAN in Automation.
Signed-off-by: Roman Fietze <roman.fietze@telemotive.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
CAN_AT91 needs HAS_IOMEM, so depends on it. The related error (with
allmodconfig under um):
CC [M] drivers/net/can/at91_can.o
drivers/net/can/at91_can.c: In function ‘at91_can_probe’:
drivers/net/can/at91_can.c:1329:2: error: implicit declaration of function ‘ioremap_nocache’ [-Werror=implicit-function-declaration]
addr = ioremap_nocache(res->start, resource_size(res));
^
drivers/net/can/at91_can.c:1329:7: warning: assignment makes pointer from integer without a cast [enabled by default]
addr = ioremap_nocache(res->start, resource_size(res));
^
drivers/net/can/at91_can.c:1384:2: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
iounmap(addr);
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/mips/net/bpf_jit.c
drivers/net/can/flexcan.c
Both the flexcan and MIPS bpf_jit conflicts were cases of simple
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch increases the mask in the FLEXCAN_MCR_MAXMB() to 7 bits as in the
newer flexcan cores the MAXMB field is 7 bits wide.
Reported-by: David Jander <david@protonic.nl>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
After sending a RTR frame the TX mailbox becomes a RX_EMPTY mailbox. To avoid
side effects when the RX-FIFO is full, this patch puts the TX mailbox into
TX_INACTIVE mode in the transmission complete interrupt handler. This, of
course, leaves a race window between the actual completion of the transmission
and the handling of tx-complete interrupt. However this is the best we can do
without busy polling the tx complete interrupt.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch implements the workaround mentioned in ERR005829:
ERR005829: FlexCAN: FlexCAN does not transmit a message that is enabled to
be transmitted in a specific moment during the arbitration process.
Workaround: The workaround consists of two extra steps after setting up a
message for transmission:
Step 8: Reserve the first valid mailbox as an inactive mailbox (CODE=0b1000).
If RX FIFO is disabled, this mailbox must be message buffer 0. Otherwise, the
first valid mailbox can be found using the "RX FIFO filters" table in the
FlexCAN chapter of the chip reference manual.
Step 9: Write twice INACTIVE code (0b1000) into the first valid mailbox.
Signed-off-by: David Jander <david@protonic.nl>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Apparently mailboxes may contain random data at startup, causing some of them
being prepared for message reception. This causes overruns being missed or even
confusing the IRQ check for trasmitted messages, increasing the transmit
counter instead of the error counter.
This patch initializes all mailboxes after the FIFO as RX_INACTIVE.
Signed-off-by: David Jander <david@protonic.nl>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes the initialization of the TX mailbox. It is now correctly
initialized as TX_INACTIVE not RX_EMPTY.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add PCI ID definition for the single channel PCAN ExpressCard 34 adapter. Due
to the subsystem id evaluation the correct number of channels (here 1) is
created at initialization time. Tested including the LED functionality.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Dong Aisheng
David Cohen
Marc Kleine-Budde
Sudip Mukherjee
Alexey Khoroshilov
Roman Fietze
Thomas Körper
Chen Gang
David S. Miller
David Dueck
David Jander
Oliver Hartkopp