This patch resurrects an old never-finished driver for Toshiba PCI SD
controllers found in some older Toshiba laptops (such as Portege R100):
02:0d.0 System peripheral [0880]: Toshiba America Info Systems SD TypA Controller [1179:0805] (rev 05)
The code is fixed, cleaned up and successfully tested with SD, SDHC, SDXC and
MMC cards on Portege R100. (MMC cards don't even work in Windows!)
SDIO probably does not work (don't have any SDIO card).
The hardware is slow (around 2 MB/s - same in Windows) because it does not
support bus mastering (busmaster enable bit cannot be set in PCI control reg).
Also the card clock is limited to 16MHz (33MHz PCI clock divided by 2).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Exynos7 has a DWMMC controller (v2.70a) which is different from
prior versions. This patch adds new compatible strings for exynos7.
This patch also fixes the CLKSEL register offset on exynos7.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Tested-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_do_hw_reset(), mmc_power_up() and mmc_power_off() all set similar
initial values for bus_mode, bus_width, chip_select and timing. Let's
make this handling simpler and more consistent by sticking them
together in a common function. This will introduce small changes in
behavior in the following places:
mmc_power_off():
For SPI hosts, explicitly set bus_mode = MMC_BUSMODE_PUSHPULL and
chip_select = MMC_CS_HIGH, before we left them as they were.
For non-SPI hosts, set bus_mode = MMC_BUSMODE_PUSHPULL instead of
MMC_BUSMODE_OPENDRAIN as before.
These two changes should not be a problem since the device will be
powered off anyway.
mmc_do_hw_reset():
Always set bus_mode = MMC_BUSMODE_PUSHPULL, as required by SD/SDIO
cards. MMC cards require MMC_BUSMODE_OPENDRAIN, but this is taken
care of by mmc_init_card() and mmc_attach_mmc().
Signed-off-by: Johan Rudholm <johanru@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
omap_hsmmc only supports one slot. So slot id is always zero, and
slot id was never used in the callbacks anyway
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
These callbacks are set during driver probe and not from the platform
init, -- evtl. they had been for oamp 1/2 -- for omap3 they are local
functions of the driver. These indirection could be dropped
altogether in favor of regular function calls TODO
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
this is needed when installing callbacks in the host struct and not
in the platform data, e.g. cover detect irq should be stored in
omap_hsmmc_host and not platform data
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
omap_hsmmc supports only one slot per controller, see OMAP_MMC_MAX_SLOTS.
This unnecessary indirection leads to confusion in the omap_hsmmc driver.
For example the card_detect callback is not installed by platform code
but from the driver probe function. So it should be a field of
omap_hsmmc_host. But since it is declared under the platform slot while
the drivers struct omap_hsmmc_host has no slot abstraction, this looks
like a bug, especially when not familiar that this driver only supports
1 slot anyway.
Either we should add a slot abstraction to omap_hsmmc_host or remove
it from the platform data struct. Removed since slot multiplexing is
an un-implemented feature
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
these fields are never read, probably an unimplemented feature
or superseded by pm_runtime
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
platform data is built from omap2_hsmmc_info, remove all fields that
are never set in omap_hsmmc_info, hence never copied to platform data.
Note that the omap_hsmmc driver is not affected by this patch those
fields were completely unused.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- omap mmc driver supports multiplexing, omap_mmc_hs doesn't
this leads to one of the major confusions in the omap_hsmmc driver
- platform data should be read-only for the driver
most callbacks are not set by the omap3 platform init code while still
required. So they are set from the driver probe function, which is against
the paradigm that platform-data should not be modified by the driver
typical examples are card_detect, read_only callbacks
un-bundling by searching for driver name \"omap_hsmmc in the
arch/arm folder. omap_hsmmc_platform_data is not initialized directly,
but from omap2_hsmmc_info, which is defined in a separate header file
not touched by this patch
hwmod includes platform headers to declare features of the platform. All
the declared features are prefixed OMAP_HSMMC. There is no need to
include platform header from hwmod other except for feature defines
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Only a few files really need that platform header. When later splitting
omap_mmc_platform_data into omap_mmc and omap_mmc_hs, those files
declaring an hs mmc platform data will have to change the platform
include, which is a good sanity check.
Also removing omap242x_init_mmc, which is not used anywhere, checked
with grep.
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Amend the atmel mci pin controller to optionally take a pin control
handle and set the state of the pins to:
- "default" on boot, resume and before performing an transfer.
- "sleep" on suspend().
This should make it possible to optimize energy usage for the pins
both for the suspend/resume cycle.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MMC core already has support for HS400. Add HS400
support to SDHCI driver. The SDHC Standard specification
does not define HS400 so consequently HS400 support is
non-standard. However HS400 is not selected without
the host controller setting the corresponding capability
flags so host controllers not yet supporting HS400
will not be affected. To support that, a quirk
SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400 is introduced to
enable the use of capabilities register reserved bit-63
to indicate HS400 support.
Because HS400 is non-standard for SDHCI, it is possible
that different vendors will do things in different ways.
However HS200 support faced the same issue but currently
there is only one solution. As such, no attempt has
been made to provide for alternate HS400 solutions except
for SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
1.2V HS200 mode capability is cleared if there is not a voltage
regulator that supports 1.2V. Do the same for 1.2V HS400 mode.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
supply.vqmmc is used with the IS_ERR macro which means
the value must be valid or an error code. NULL is
neither, so replace with ERR_PTR(-EINVAL).
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Synopsys DW_MMC IP core supports Internal DMA Controller with 64-bit address mode from IP version 2.70a onwards.
Updated the driver to support IDMAC 64-bit addressing mode.
Signed-off-by: Prabu Thangamuthu <prabu.t@synopsys.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
AMD SD controller supports the SDR104 mode, but caps2 can not
be promoted to support hs200 for eMMC.
Signed-off-by: Vincent Wan <vincent.wan@amd.com>
Signed-off-by: Wan Zongshun <mcuos.com@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch is to enable the quirk for AMD sdhci requiring transfer
mode register need to be cleared for commands without data
Signed-off-by: Vincent Wan <vincent.wan@amd.com>
Signed-off-by: Wan Zongshun <mcuos.com@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is possible that we may fail to set the clock rate, if we do so then
log the failure and don't bother reprogramming the IP.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ondrej Zary
Abhilash Kesavan
Johan Rudholm
Andreas Fenkart
Wenyou Yang
Adrian Hunter
Prabu Thangamuthu
Vincent Wan
Mark Brown