DW ethernet controller on HSDK hangs sometimes after SW reset, so
add reset node to make possible to reset DW ethernet controller HW.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Commit 92e5aae457 "kernel/watchdog: split up config options"
introduced SOFTLOCKUP_DETECTOR which selects LOCKUP_DETECTOR
instead of the latter to be selected itself.
We need to adjust our defconfigs accordingly.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This initial port adds support of ARC HS Development Kit board with some
basic features such serial port, USB, SD/MMC and Ethernet.
Essentially we run Linux kernel on all 4 cores (i.e. utilize SMP) and
heavily use IO Coherency for speeding-up DMA-aware peripherals.
Note as opposed to other ARC boards we link Linux kernel to
0x9000_0000 intentionally because cores 1 and 3 configured with DCCM
situated at our more usual link base 0x8000_0000. We still can use
memory region starting at 0x8000_0000 as we reallocate DCCM in our
platform code.
Note that PAE remapping for DMA clients does not work due to an RTL bug,
so CREG_PAE register must be programmed to all zeroes, otherwise it will
cause problems with DMA to/from peripherals even if PAE40 is not used.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Essentially remove CONFIG_ARC_PLAT_SIM
There is no need for any platform specific code, just the board DTS
match strings which we can include unconditionally
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Remove old, dead Kconfig option INET_LRO. It is gone since
commit 7bbf3cae65 ("ipv4: Remove inet_lro library").
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARC VDK for EVSS uses UIO for communication with Embedded Vision
Subsystem.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
In recent VDKs ARC cores are configured as "run on reset"
which made existing kernel configuration outdated to effect that
slave cores never start execution of the code keeping only master
online.
With that fix we're again in sync with VDK platform.
And while at it we regenerate defconfig via savedefconfig so default
options are now excluded.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Up until now we had ARC PGU not enabled in axs10x defconfigs trying
to not bloat kernel image again with yet another drivers and subsystems.
This change configures ARC PGU (as well as DRM bits it depends on)
to be built as a module and so those who need LCD screen to work on
axs10x may bundle built .ko files in their target's file-system with
help of the following command on host:
------------->8-------------
make INSTALL_MOD_PATH=_path_to_target_fs_ modules_install
------------->8-------------
and later on target with commands as simple as:
------------->8-------------
modprobe adv7511.ko
modprobe arcpgu.ko
------------->8-------------
get LCD working.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
There are more ARC Linux HAPS users than Zebu ones.
Same kernel would work fine on both, even with embedded DT, assuming the FPGA
bitfile configuration is same
Suggested-by: Francois Bedard <fbedard@ynopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The original distinction was done as they were developed at different
times and primarily because they are specific to UP (RTC) and SMP (GFRC).
But given that driver handles that at runtime, (i.e. not allowing
RTC as clocksource in SMP), we can simplify things a bit.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Now when we have properly working performance counters in nSIM
even with interrupt support (fix should be a part of upcoming
nSIM engineering build 2016.12-005) we may enable perf support
by default for all platforms that use nSIM for ARC cores simulation.
Note 1: PCT node was missing for some reason in nsimosci.dts
while all other nSIM-related .dts files already had
PCT node for quite some time, so adding it now.
Note 2: All defconfigs were regenerated with "make savedefconfig"
which led to some clean-ups in nsimosci_hs_smp_defconfig:
CONFIG_FRAMEBUFFER_CONSOLE=y was removed because it is
automatically selected now by DRM.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The cool thing is that same kernel image can run on
- nsim OSCI simulation platform
- SDPlite FPGA setups
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
With required ARC PGU updates that allow it to be used on simulation
platforms we may finally utilize ARC PGU in nSIM OSCI virtual platforms
with modern Linux kernels.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
With required ARC PGU updates that allow it to be used on simulation
platforms we may finally utilize ARC PGU in HS38 VDK with modern
Linux kernels.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
As mentioned in LTP's README.ARC:
------------->8------------
Requirements for the environment
* Linux must be built with support of loop block devices. Thus it's
necessary to enable these Linux kernel options:
CONFIG_BLK_DEV
CONFIG_BLK_DEV_LOOP
------------->8------------
enabling loop block devices.
That among other things lead to additional 10 fatal signals
appearing during LTP run.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Since ezchip network driver was adapted to little endian architecture
this patch provides the corresponding arch/arc/{boot/dts,configs}/ updates so
we can switch over to this device-model/driver for OSCI platform.
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Lada Trimasova <ltrimas@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The problem is with CONFIG_CPU_BIG_ENDIAN=y we still needed .config
fixup to override the the defconfig prefix to arceb-linux-
So remove these from defconfig and let user pass this via CROSS_COMPILE
environment var or use the default for ENDIAN (per previous patch)
No other arch carries them in defconfigs anyways !
Cc: Noam Camus <noamc@ezchip.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Anton Kolesov <akolesov@synosys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Even though DEVTMPFS is required when our pre-built initramfs
is used it is not the case in general. It is perfectly possible
to use initramfs with device nodes already populated or there
could be other usages, see discussion below for more detials:
http://thread.gmane.org/gmane.comp.embedded.openwrt.devel/37819/focus=37821
This change removes mentioned dependency from arch/arc/Kconfig
updating instead those defconfigs that are usually used with this
kind of pre-build initramfs.
And while at it all touched defconfigs were regenerated via
savedefconfig and some options were removed:
* USB is selected by other options implicitly
* VGA_CONSOLE is disableb for ARC since
031e29b587
* EXT3_FS automatically selects EXT4_FS
* MTDxxx and JFFS2_FS make no sense for AXS because
AXS NAND controller is not upstreamed
* NET_OSCI_LAN is not in upstream as well
* ARCPGU_xxx options make no sense because ARC PGU is not yet
in upstream and when it gets there all config options would
be taken from devicetree
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
When building kernel with buildroot built toolchain, CROSS_COMPILE
currently needs adjustment even if minor. This is because the defconfigs
prefer "arc-linux-uclibc-" prefix from hand built (non buildroot) toolchain
while buildroot provides "arc-buildroot-linux-uclibc-"
To avoid this use the common "arc-linux-" prefix which is provided by
buildroot and has also been in hand built tools for quite some time.
Signed-off-by: sujayraaj <sujayraaj@gmail.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
[vgupta: updated changelog]
DesignWare MMC Controller's transfer mode should be decided
at runtime instead of compile-time. So we remove this config
option and read dw_mmc's register to select DMA master.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Eugeniy Paltsev
Alexey Brodkin
Vineet Gupta
Krzysztof Kozlowski
Alexey Brodkin
Noam Camus
Lada Trimasova
sujayraaj
Shawn Lin
Ruud Derwig