Added MAINTAINERS entry for the Atmel AT91RM9200.
Accept (some) responsibility...
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Updated some of the comments in the atmel_serial.h header detailing
which bits are only available on the AT91RM9200 or the AT91SAM9xx
processors.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The USB Device port registers are already defined in
drivers/usb/gadget/at91_udc.h. This file can therefore just be removed.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. The CPU identification has moved from <system.h> to <cpu.h>.
2. AT91RM9200_BASE_US0 is only defined if we are compiling in support
for the AT91RM9200. Therefore we need to replace the CONFIG_ARM ifdef
with CONFIG_ARCH_AT91RM9200
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Replace the 'is_b' variable with 'slot_b' in at91_mmc_data.
Also add the new 'chipselect' variable for CF/PCMCIA and 'bus_width_16'
variable for NAND.
This (and previous patches) will unfortunately break the current MMC,
USB Gadget and PCMCIA drivers. Updates and fixes for those drivers will
be submitted to the various subsystem maintainers.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
XScale cores either have a DSP coprocessor (which contains a single
40 bit accumulator register), or an iWMMXt coprocessor (which contains
eight 64 bit registers.)
Because of the small amount of state in the DSP coprocessor, access to
the DSP coprocessor (CP0) is always enabled, and DSP context switching
is done unconditionally on every task switch. Access to the iWMMXt
coprocessor (CP0/CP1) is enabled only when an iWMMXt instruction is
first issued, and iWMMXt context switching is done lazily.
CONFIG_IWMMXT is supposed to mean 'the cpu we will be running on will
have iWMMXt support', but boards are supposed to select this config
symbol by hand, and at least one pxa27x board doesn't get this right,
so on that board, proc-xscale.S will incorrectly assume that we have a
DSP coprocessor, enable CP0 on boot, and we will then only save the
first iWMMXt register (wR0) on context switches, which is Bad.
This patch redefines CONFIG_IWMMXT as 'the cpu we will be running on
might have iWMMXt support, and we will enable iWMMXt context switching
if it does.' This means that with this patch, running a CONFIG_IWMMXT=n
kernel on an iWMMXt-capable CPU will no longer potentially corrupt iWMMXt
state over context switches, and running a CONFIG_IWMMXT=y kernel on a
non-iWMMXt capable CPU will still do DSP context save/restore.
These changes should make iWMMXt work on PXA3xx, and as a side effect,
enable proper acc0 save/restore on non-iWMMXt capable xsc3 cores such
as IOP13xx and IXP23xx (which will not have CONFIG_CPU_XSCALE defined),
as well as setting and using HWCAP_IWMMXT properly.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Create include/asm-arm/arch-ixp4xx/udc.h and
add platfrom device ixp4xx_udc_device into
arch/arm/mach-ixp4xx/common.c.
This allows us to use pxa2xx-udc on
the ixp4xx platfrom. Both pxa2xx and
ixp4xx use the same device controller.
Signed-off-by:Milan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch contains various updates the at91rm9200_devices.c file:
* Consistent naming of resources and platform_devices.
* PCMCIA/Compact Flash: Configuration of the memory controller
moved out of the driver and into this file.
* MMC: Enable the VCC pin (if one is configured)
* MMC: Enable the internal pullups on the I/O pins.
* NAND: Configuration of the memory controller moved out of the
driver and into this file.
* Added TWI/I2C resources.
* The names of some of the CONFIG_ variables were changed.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A number of configuration file changes.
These are mainly to replace references to ARCH_AT91RM9200 and
ARCH_AT91SAM9261 with the common/generic ARCH_AT91. That way we don't
need to mention every specific AT91 processor explicitly.
Also adds the configuration option for AT91SAM9260-EK and AT91SAM9261-EK
boards.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The master abort check in ixp2000_pci_read_config() recently started
failing due to the compiler optimising out the read access following
the clearing of pci_master_aborts. Mark pci_master_aborts volatile to
force the compiler to reload it on every use.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch includes a number of small changes for integrating the
AT91SAM9261 and AT91SAM0260 support.
* Can only select support for one AT91 processor at a time.
* Remove most of the remaining static memory mapping for the
AT91RM9200.
* Reserve 1Mb of memory below the IO for mapping the internal SRAM
and any custom board-specific devices (ie, FPGA).
* The SAM9260 has more serial ports, so increase the maximum to 7.
* Define the standard chipselect addresses, and define other
addresses relative to those.
* CLOCK_TICK_RATE is different on the SAM926x's.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The bits used to select the USB clocks are different on the SAM9's.
Add support for the HCK clocks on the AT91SAM9261.
Patch from Patrice Vilchez & Nicolas Ferre
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch converts the old CONFIG_MTD_PHYSMAP_ options to the new
physmap API by creating a physmap platform device for the NOR flash
found on the Atmel AT91RM9200-DK and AT91RM9200-EK boards.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch updates the Carmeva board support:
* Specify the MMC Write-protect and Detection pins.
* Add configuration of SPI devices.
Patch from Peer Georgi.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Attached is a patch for at91rm9200_time.c which removes
the 'BUG: soft lockup detected on CPU#0!' message when
exiting suspended states.
Patch from Savin Zlobec
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch includes the pin initialization, resource definition and
registration of the platform_devices for the SAM9260 and SAM9261
processors.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the timer on the Atmel AT91SAM9261 and AT91SAM9260
processors.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Most architectures have fairly simple discontiguous memory - a
simple set of successive regions each containing some memory.
These can be described simply as a log2 of their maximum size,
along with the base address of the first region and the number
of regions.
The base address is already described by PHYS_PFN_OFFSET, and
the number of regions via the MAX_NUMNODES and the number of
online nodes.
If we then supply the log2 of their maximum size, all the other
discontigmem macros can move into generic code.
There is one exception: lh7a40x seems to have a more complicated
setup; this is left alone.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds definitions for the new peripherals integrated in the
AT91SAM9260 and AT91SAM9261 processors: ECC, LCD, RSTC, RTT, SHDWC,
WDT, MATRIX, SDRAMC, SMC.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch updates the drivers (and other files) which include the
hardware headers. This fixes the breakage introduced in patches 3950/1
and 3951/1 (those patches were getting big).
The AVR32 architecture uses the same serial driver and had its own copy
of at91rm9200_pdc.h. Renamed it to at91_pdc.h
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Andrew Victor
Lennert Buytenhek
Dan Williams
Milan Svoboda
Russell King