This patch converts the drivers in drivers/input/* to use the
module_spi_driver() macro which makes the code smaller and a bit
simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In ancient times it was necessary to manually initialize the bus field of an
spi_driver to spi_bus_type. These days this is done in spi_driver_register(),
so we can drop the manual assignment.
The patch was generated using the following coccinelle semantic patch:
// <smpl>
@@
identifier _driver;
@@
struct spi_driver _driver = {
.driver = {
- .bus = &spi_bus_type,
},
};
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
With commit 67d0a07544 we mark strict_strtox
as obsolete. Convert all remaining such uses in drivers/input/.
Also change long to appropriate types, and return error conditions
from kstrtox separately, as Dmitry sugguests.
Signed-off-by: JJ Ding <dgdunix@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
A pending cleanup will mean that module.h won't be implicitly
everywhere anymore. Make sure the modular drivers in input dir
are actually calling out for <module.h> explicitly in advance.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Use gpio_request_one() instead of multiple gpiolib calls.
This also simplifies error handling a bit.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The pendown gpio was requested but not configured for input.
Configure it for input.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Just set vref_mv in your platform config to use external vref. Otherwise
the internal one is used.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
req.sample needs its own cacheline otherwise accessing req.msg fetches
it in again.
Note: This effect doesn't occur if the underlying SPI driver doesn't use
DMA at all.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When driver uses custom pendown detection method gpio_pendown is not
set up and so we should not try to free it, otherwise we are presented
with:
------------[ cut here ]------------
WARNING: at drivers/gpio/gpiolib.c:1258 gpio_free+0x100/0x12c()
Modules linked in:
[<c0061208>] (unwind_backtrace+0x0/0xe4) from [<c0091f58>](warn_slowpath_common+0x4c/0x64)
[<c0091f58>] (warn_slowpath_common+0x4c/0x64) from [<c0091f88>](warn_slowpath_null+0x18/0x1c)
[<c0091f88>] (warn_slowpath_null+0x18/0x1c) from [<c024e610>](gpio_free+0x100/0x12c)
[<c024e610>] (gpio_free+0x100/0x12c) from [<c03e9fbc>](ads7846_probe+0xa38/0xc5c)
[<c03e9fbc>] (ads7846_probe+0xa38/0xc5c) from [<c02cff14>](spi_drv_probe+0x18/0x1c)
[<c02cff14>] (spi_drv_probe+0x18/0x1c) from [<c028bca4>](driver_probe_device+0xc8/0x184)
[<c028bca4>] (driver_probe_device+0xc8/0x184) from [<c028bdc8>](__driver_attach+0x68/0x8c)
[<c028bdc8>] (__driver_attach+0x68/0x8c) from [<c028b4c8>](bus_for_each_dev+0x48/0x74)
[<c028b4c8>] (bus_for_each_dev+0x48/0x74) from [<c028ae08>](bus_add_driver+0xa0/0x220)
[<c028ae08>] (bus_add_driver+0xa0/0x220) from [<c028c0c0>](driver_register+0xa8/0x134)
[<c028c0c0>] (driver_register+0xa8/0x134) from [<c0050550>](do_one_initcall+0xcc/0x1a4)
[<c0050550>] (do_one_initcall+0xcc/0x1a4) from [<c00084e4>](kernel_init+0x14c/0x214)
[<c00084e4>] (kernel_init+0x14c/0x214) from [<c005b494>](kernel_thread_exit+0x0/0x8)
---[ end trace 4053287f8a5ec18f ]---
Also rearrange ads7846_setup_pendown() to have only one exit point
returning success.
Reported-by: Sourav Poddar <sourav.poddar@ti.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Reviewed-by: Charulatha V <charu@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is a move to deprecate bus-specific PM operations and move to
using dev_pm_ops instead in order to reduce the amount of boilerplate
code in buses and facilitate updates to the PM core. Do this move for
the ads7846 driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Michael Hennerich <Michael.Hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit 9114337 introduces regulator operations in ads7846 touchscreen
driver. Among these operations, some are called while holding a
spinlock. On many platforms regulators reside on slow buses, such as
I2C/SPI and require sleep while accessing them.
The touchscreen itself is also a SPI device and currently relies on
asynchronous SPI access to avoid sleeping in interrupt context. Let's
switch to using threaded IRQ to be able to access SPI bus
synchronously (which simplifies driver a bit); it also allows safe
access to the regulators as well.
This has been tested on the ti_omap3530evm board:
1) using ts_lib after normal boot
2) using ts_lib after "#echo 1/0 > /sys/bus/spi/devices/spi0.1/disable"
3) using ts_lib after "#echo mem > /sys/power/state" and "wake up"
Also tested on pandora.
Based on original patch by Dmitry Torokhov.
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
ADS7845 is a controller for 5-wire touch screens and somewhat
different from 7846. It requires three serial communications to
accomplish one complete conversion. Unlike 7846 it doesn't allow
Z1-/Z2- position measurement.
The patch extends the ads7846 driver to also support ads7845.
The packet struct is extended to contain needed command and
conversion buffers. ads7846_rx() and ads7846_rx_val() now
differentiate between 7845 and 7846 case. ads7846_probe() is
modified to setup ads7845 specific command and conversion
messages and to switch ads7845 into power-down mode, since
this is needed to be prepared to respond to pendown interrupts.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
On some platforms, for example with GPIO interrupts on mpc5121,
it is not possible to configure falling edge interrupts.
Specifying irq trigger type in platform data structure
allows using ads7846 driver on such platforms.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch fixes the follwing warning introduced by commit
067fb2f648 ("Input: ads7846 - return error on
regulator_get() failure"):
drivers/input/touchscreen/ads7846.c: In function 'ads7846_probe':
drivers/input/touchscreen/ads7846.c:1167: warning: format '%ld' expects
type 'long int', but argument 4 has type 'int'
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In probe(), if regulator_get() failed, an error code was not being
returned causing the driver to be successfully bound, even though
probe failed. This in turn caused the suspend, resume and remove
methods to be registered and accessed via the SPI core. Since these
functions all access private driver data using pointers that had been
freed during the failed probe, this would lead to unpredictable
behavior.
This patch ensures that probe() returns an error code in this failure
case so the driver is not bound.
Found using lockdep and noticing the lock used in the suspend/resum
path pointed to a bogus lock due to the freed memory.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add wakeup support to the ads7846 driver. Platforms can enable wakeup
capability by setting the wakeup flag in ads7846_platform_data. With this
patch the ads7846 driver can be used to wake the system from suspend.
Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The AD7873 is almost identical to the ADS7846; the only difference is
related to the Power Management bits PD0 and PD1. This results in a
slightly different PENIRQ enable behavior. For the AD7873, VREF should
be turned off during differential measurements.
So, add the AD7873/43 to the list of driver supported devices, and prevent
VREF usage during differential/ratiometric conversion modes.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The ADS7846/TSC2046 touchscreen controllers can (and usually are)
connected to various regulators for power, so add regulator support.
Valid regulator will now be required, so boards without complete
regulator setup should either disable regulator framework or enable
CONFIG_REGULATOR_DUMMY.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
On Zaurus, hx4700 and others pressure is reported inverted -- the lighter
the pressure, the bigger numerical value.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Axel Lin
Lars-Peter Clausen
Dmitry Torokhov
JJ Ding
Paul Gortmaker
Igor Grinberg
Alexander Stein
Mark Brown
Jason Wang
Anatolij Gustschin
Kevin Hilman
Ranjith Lohithakshan
Michael Hennerich
Grazvydas Ignotas
Pavel Machek