Latest VBT mentions which set of registers will be used for BLC,
as controller number field. Making use of this field in BXT
BLC implementation. Also, the registers are used in case control
pin indicates display DDI. Adding a check for this.
According to Bspec, BLC_PWM_*_2 uses the display utility pin for output.
To use backlight 2, enable the utility pin with mode = PWM
v2: Jani's review comments
addressed
- Add a prefix _ to BXT BLC registers definitions.
- Add "bxt only" comment for u8 controller
- Remove control_pin check for DDI controller
- Check for valid controller values
- Set pipe bits in UTIL_PIN_CTL
- Enable/Disable UTIL_PIN_CTL in enable/disable_backlight()
- If BLC 2 is used, read active_low_pwm from UTIL_PIN polarity
Satheesh's review comment addressed
- If UTIL PIN is already enabled, BIOS would have programmed it. No
need to disable and enable again.
v3: Jani's review comments
- add UTIL_PIN_PIPE_MASK and UTIL_PIN_MODE_MASK
- Disable UTIL_PIN if controller 1 is used
- Mask out UTIL_PIN_PIPE_MASK and UTIL_PIN_MODE_MASK before enabling
UTIL_PIN
- check valid controller value in intel_bios.c
- add backlight.util_pin_active_low
- disable util pin before enabling
v4: Change for BXT-PO branch:
Stubbed unwanted definition which was existing before
because of DC6 patch.
UTIL_PIN_MODE_PWM (0x1b << 24)
v2: Fixed Jani's review comment.
v3: Split the backight PWM frequency programming into separate patch,
in cases BIOS doesn't initializes it.
v4: Starting afresh and not modifying existing state for backlight, as
per Jani's recommendation.
v5: Fixed Jani's review comment wrt util pin enable
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Previously we've relied on having basically one backlight and one
backlight type per platform. This is already a bit quirky with PMIC PWM
support on VLV/CHV platforms with MIPI DSI. In the foreseeable future
we'll have at least DPCD based backlight control on eDP and DCS command
based backlight control on MIPI DSI. Backlight is becoming more and more
connector specific, so reflect this fact by making the backlight control
hooks connector specific.
This enables further work to reuse generic backlight code in
intel_panel.c while adding more specific backlight code accessed via the
hooks.
Cc: Deepak M <m.deepak@intel.com>
Cc: Yetunde Adebisi <yetundex.adebisi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Deepak M <m.deepak@intel.com>
Reviewed-by: Yetunde Adebisi <yetundex.adebisi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make adjusted_mode const whereever we don't have to modify it. This only
covers cases when we have a local adjusted_mode variable, and doesn't
make any difference for cases where we just dereference
pipe_config->adjusted_mode.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The adjustead_mode crtc_ timings are what we will program into the hardware,
so it's those timings we should be looking practically everywhere.
The normal and crtc_ timings should differ only when stere doubling is
used. In that case the normal timings are the orignal non-doubled
timigns, and crtc_ timings are the doubled timings used by the hardware.
The only case where we continue to look at the normal timings is when we
pass the adjusted_mode to drm_match_{cea,hdmi}_mode() to find the VIC.
drm_edid keeps the modes aronund in the non-double form only, so it
needs the non-double timings to match against.
Done with sed
's/adjusted_mode->\([vhVH]\)/adjusted_mode->crtc_\1/g'
's/adjusted_mode->clock/adjusted_mode->crtc_clock/g'
with a manual s/VDisplay/vdisplay/ within the comment in intel_dvo.c
v2: Update due to intel_dsi.c changes
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rename the function argument to 'adjusted_mode' whenever the function
only ever gets passed the adjusted_mode.
v2: Update due to intel_dsi.c changes
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently everyone and their dog has their own favourite spelling
for vga_switcheroo. This makes it hard to grep dmesg for log entries
relating to vga_switcheroo. It also makes it hard to find related
source files in the tree.
vga_switcheroo.c uses pr_fmt "vga_switcheroo". Use that everywhere.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Normally we determine the backlight PWM modulation frequency (which we
also use as backlight max value) from the backlight registers at module
load time, expecting the registers have been initialized by the BIOS. If
this is not the case, we fail.
The VBT contains the backlight modulation frequency in Hz. Add platform
specific functions to convert the frequency in Hz to backlight PWM
modulation frequency, and use them to initialize the backlight when the
registers are not initialized by the BIOS.
v2: Fix SPT and VLV. Thanks to Clint for the VLV code.
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently the difference between backlight control on HSW vs. BDW/SKL is
that on HSW we modify the duty cycle on the CPU register, and have the
hardware pass the changes on to the PCH registers. We still drive the
PCH PWM on both. While HSW and BDW use the same LPT PCH, BDW does not
pass these messages on to the PCH. Therefore on BDW we need to enable
the PCH override bit, and program the PCH directly. (On SPT PCH, this
mode is the default.) We could as well do this on HSW too, and in fact
I've been told this is what a certain other operating system does. So
use PCH backlight override on HSW too.
This simplifies some follow-up code, but it does have the danger of
breaking backlight on HSW machines. It should work, but mysterious are
the ways of backlight.
While at it, name the related backlight hooks according to the PCH
rather than the CPU for clarity.
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the CRC PWM device in intel_panel.c and add new MIPI backlight
specififc callbacks
v2: Modify to use pwm_config callback
v3: Addressed Jani's comments
- Renamed all function as pwm_* instead of vlv_*
- Call intel_panel_actually_set_backlight in enable function
- Return -ENODEV in case pwm_get fails
- in case pwm_config error return error cdoe from pwm_config
- Cleanup pwm in intel_panel_destroy_backlight
v4: Removed unused #defines and initialized backlight with INVALID_PIPE (Ville)
CC: Samuel Ortiz <sameo@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some 855gm models (at least ThinkPad X40) regressed because of
commit b0cd324fae
Author: Jani Nikula <jani.nikula@intel.com>
Date: Wed Nov 12 16:25:43 2014 +0200
drm/i915: don't save/restore backlight hist ctl registers
which tried to make our driver more robust by not blindly saving and
restoring registers, but it failed to take into account
commit 0eb96d6ed3
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Wed Oct 14 12:33:41 2009 -0700
drm/i915: save/restore BLC histogram control reg across suspend/resume
Fix the regression by enabling hist ctl on gen2.
v2: Improved the comment.
v3: Improved the comment, again.
Reported-and-tested-by: Philipp Gesang <phg@phi-gamma.net>
References: http://mid.gmane.org/20150623222648.GD12335@acheron
Fixes: b0cd324fae ("drm/i915: don't save/restore backlight hist ctl registers")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Enabling BLC on BXT.
Includes register definition, and new functions for BXT.
In BXT, there are 2 sets of registers for BLC. Until there is clarity
about which set would be effective, set 1 is being used.
This would have to be re-visited if there is any change or when 2 LFPs are
enabled on BXT.
This patch enables brightness change which would be effected by use of
hot-keys or sysfs entry.
TODO:- BLC implementation will have to re-visited when
1. there is clarity about which set of registers has to be used and when.
2. CDCLK frequency is changed
v2: Jani's review comments
- Modified comment in i915_reg.h
- Renamed register defintions
- Removed definition of duty cycle max. Not required now and its not 64-bit.
v3:
- Rebase on top of VLV/CHV backlight changes, in particuliar
bxt_set_backlight() now has a different prototype (Damien)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Shankar, Uma <uma.shankar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull drm updates from Dave Airlie:
"This is the main drm pull, it has a shared branch with some alsa
crossover but everything should be acked by relevant people.
New drivers:
- ATMEL HLCDC driver
- designware HDMI core support (used in multiple SoCs).
core:
- lots more atomic modesetting work, properties and atomic ioctl
(hidden under option)
- bridge rework allows support for Samsung exynos chromebooks to
work finally.
- some more panels supported
i915:
- atomic plane update support
- DSI uses shared DSI infrastructure
- Skylake basic support is all merged now
- component framework used for i915/snd-hda interactions
- write-combine cpu memory mappings
- engine init code refactored
- full ppgtt enabled where execlists are enabled.
- cherryview rps/gpu turbo and pipe CRC support.
radeon:
- indirect draw support for evergreen/cayman
- SMC and manual fan control for SI/CI
- Displayport audio support
amdkfd:
- SDMA usermode queue support
- replace suballocator usage with more suitable one
- rework for allowing interfacing to more than radeon
nouveau:
- major renaming in prep for later splitting work
- merge arm platform driver into nouveau
- GK20A reclocking support
msm:
- conversion to atomic modesetting
- YUV support for mdp4/5
- eDP support
- hw cursor for mdp5
tegra:
- conversion to atomic modesetting
- better suspend/resume support for child devices
rcar-du:
- interlaced support
imx:
- move to using dw_hdmi shared support
- mode_fixup support
sti:
- DVO support
- HDMI infoframe support
exynos:
- refactoring and cleanup, removed lots of internal unnecessary
abstraction
- exynos7 DECON display controller support
Along with the usual bunch of fixes, cleanups etc"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (724 commits)
drm/radeon: fix voltage setup on hawaii
drm/radeon/dp: Set EDP_CONFIGURATION_SET for bridge chips if necessary
drm/radeon: only enable kv/kb dpm interrupts once v3
drm/radeon: workaround for CP HW bug on CIK
drm/radeon: Don't try to enable write-combining without PAT
drm/radeon: use 0-255 rather than 0-100 for pwm fan range
drm/i915: Clamp efficient frequency to valid range
drm/i915: Really ignore long HPD pulses on eDP
drm/exynos: Add DECON driver
drm/i915: Correct the base value while updating LP_OUTPUT_HOLD in MIPI_PORT_CTRL
drm/i915: Insert a command barrier on BLT/BSD cache flushes
drm/i915: Drop vblank wait from intel_dp_link_down
drm/exynos: fix NULL pointer reference
drm/exynos: remove exynos_plane_dpms
drm/exynos: remove mode property of exynos crtc
drm/exynos: Remove exynos_plane_dpms() call with no effect
drm/i915: Squelch overzealous uncore reset WARN_ON
drm/i915: Take runtime pm reference on hangcheck_info
drm/i915: Correct the IOSF Dev_FN field for IOSF transfers
drm/exynos: fix DMA_ATTR_NO_KERNEL_MAPPING usage
...
The objective is to make this structure usable with the atomic helpers,
so let's start with the rename. Patch generated with coccinelle:
@@ @@
-struct intel_crtc_config {
+struct intel_crtc_state {
...
}
@@ @@
-struct intel_crtc_config
+struct intel_crtc_state
v2: Completely generate the patch with cocci. (Ander)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
commit 6dda730e55
Author: Jani Nikula <jani.nikula@intel.com>
Date: Tue Jun 24 18:27:40 2014 +0300
drm/i915: respect the VBT minimum backlight brightness
introduced a bug which resulted in inconsistent brightness levels on
different machines. If a suspended was entered with the screen off some
machines would resume with the screen at minimum brightness and others
at maximum brightness.
The following commands can be used to produce this behavior.
xset dpms force off
sleep 1
sudo systemctl suspend
(resume ...)
The root cause of this problem is a comparison which checks to see if
the backlight level is zero when the panel is enabled. If it is zero,
it is set to the maximum level. Unfortunately, not all machines have a
minimum level of zero. On those machines the level is left at the
minimum instead of begin set to the maximum.
Fix the bug by updating the comparison to check for the minimum
backlight level instead of zero. Also, expand the comparison for
the possible case when the level is less than the minimum.
Fixes: 6dda730e55 ("respect the VBT minimum backlight brightness")
Signed-off-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
So with all the code movement and extraction in intel_pm.c in -next
git is hopelessly confused with
commit 2208d655a9
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Nov 14 09:25:29 2014 +0100
drm/i915: drop WaSetupGtModeTdRowDispatch:snb
from -fixes. Worse even small changes in -next move around the
conflict context so rerere is equally useless. Let's just backmerge
and be done with it.
Conflicts:
drivers/gpu/drm/i915/i915_drv.c
drivers/gpu/drm/i915/intel_pm.c
Except for git getting lost no tricky conflicts really.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Now that the backlight device no longer gets registered too early we
should be able to drop most of the INVALID_PIPE checks from the backlight
code.
The only exceptio is the opregion stuff where we may (in theory at
least) get a request from the BIOS already during driver init as soon as
the backlight setup has been done. In which case we can still get the
INVALID_PIPE from intel_get_pipe_from_connector(). So leave that check
in place, and add a comment explaining why.
For the rest, if we still manage to get here with INVALID_PIPE on
VLV/CHV we will now get a WARN from the lower level functions and
can then actually investigate further.
v2: Leave the check in the BIOS related code (Jani)
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we register the backlight device as soon as we register the
connector. That means we can get backlight requests from userspace
already before reading out the current modeset hardware state.
That means we don't yet know the current crtc->encoder->connector mapping,
which causes problems for VLV/CHV which need to know the current pipe in
order to figure out which BLC registers to poke. Currently we just
ignore such requests fairly deep in the backlight code which means the
backlight device brightness property will get out of sync with our
backlight.level and the actual hardware state.
Fix the problem by delaying the backlight device registration until the
entire modeset init has been performed. And we also move the
backlight unregisteration to happen as the first thing during the
modeset cleanup so that we also won't be bothered with userspace
backlight requested during teardown.
This is a real world problem on machines using systemd, because systemd,
for some reason, wants to restore the backlight to the level it used last
time. And that happens as soon as it sees the backlight device appearing
in the system. Sometimes the userspace access makes it through before
the modeset init, sometimes not.
v2: Do not lie to the user in the debug prints (Jani)
Include connector name in the prints (Jani)
Fix a typo in the commit message (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV/CHV both pipes A and B have their own backlight control
registers. In order to correctly read out the current hardware state at
init we need to know which pipe is driving the eDP port. Pass that
information down from the eDP init code into the backlight code.
To determine the correct pipe we first look at which pipe is currently
configured in the port control register, if that look invalid we look
at which pipe's PPS is currently controlling the port, and if that
too looks invalid we just assume pipe A.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV/CHV when the display is off, we can't read out the current
backlight level from the hardware since we have no pipe to do so.
Currently we end up reading a bigus register due to passing
INVALID_PIPE to VLV_BLC_PWM_CTL().
Skip the entire .get_backlight() call if the backlight isn't enabled
according to backlight.enabled.
This problem can be reproduced simply by reading the backlight device
actual_brightness file while the display is off.
Cc: Jani Nikula <jani.nikula@intel.com>
Suggested-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VLV/CHV have backlight controls only on pipes A and B. Bail out
without touching registers that don't exist, and print a warning.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula
Williams, Dan J
Sunil Kamath
Ville Syrjälä
Lukas Wunner
Shobhit Kumar
Vandana Kannan
Javi Merino
Linus Torvalds
Ander Conselvan de Oliveira
Jeremiah Mahler
Daniel Vetter