I was going over the scsi I/O submit path, when sd_init_command
construct the scsi command, this_count is already checked in the
previous else if clause. Why does it need to check it again in
the last else block?
Patch to delete the spurious check.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
scsi_init_io calls scsi_alloc_sgtable and then calls blk_rq_map_sg
to initialize the scatterlist structure. blk_rq_map_sg() already
memset the structure for every new segment. That makes the memset
in scsi_alloc_sgtable unnecessary.
Patch to delete the extra memset in scsi_alloc_sgtable. Tested on
a x86_64 machine. Looks stable to me.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
One of the issues we had was reverting the midlayers lun value
into the 8byte lun value that we wanted to send to the device.
Historically, there's been some combination of byte swapping,
setting high/low, etc. There's also been no common thread between
how our driver did it and others. I also got very confused as
to why byteswap routines were being used.
Anyway, this patch is a LLDD-callable function that reverts the
midlayer's lun value, stored in an int, to the 8-byte quantity
(note: this is not the real 8byte quantity, just the same amount
that scsilun_to_int() was able to convert and store originally).
This also solves the dilemma of the thread:
http://marc.theaimsgroup.com/?l=linux-kernel&m=112116767118981&w=2
A patch for the lpfc driver to use this function will be along
in a few days (batched with other patches).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Cleanup FC remote port registration.
Due to the inherent behaviour (an immediate scan) of adding
a 'target'-role-capable rport via fc_remote_port_add(),
split the registration into two steps -- addition as
unknown-type role, then use fc_remote_port_rolchg() with
appropriate role (based on PLOGI/PRLI bits). This allows
for a more cleaner rport->dd_data management as can be seen
with the simplified qla2xxx_slave_alloc() function.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Consolidate ISP24xx chip reset logic.
Consolidate near-duplicate RISC reset logic from
qla24xx_reset_chip() and qla24xx_chip_diag(). Also, after
initiating a soft-reset, insure the firmware has completed
all NVRAM accesses before continuing.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add firmware version number to qla24xx_fw_version_str().
Original code was accidently trimmed during port.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The wrong sgmap structure is being assigned in aac_send_raw_srb.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Correct maximum supported lun and target-id definitions.
The driver uses command-IOCBs which support a maximum lun
value of 0xffff -- correct #define to reflect the change.
Also, remove superfluous MAX_TARGET definition.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add ISP24xx ISR routines.
Add appropriate glue-code for ISP24xx support -- this
included generalizing some of the core handling
routines (qla2x00_async_event() [pull-up retrieval of
mailbox values] and qla2x00_status_entry()]. Fixup
2100/2300 ISRs to handle the new conventions.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add ISP24xx IOCB manipulation routines.
Add appropriate glue-code for ISP24xx support while
manipulting IOCB packets. Add an ISP24xx specific
'start_scsi' routine due to command-type-7 layout
changes.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add ISP24xx flash-manipulation routines.
Add read/write flash manipulation routines for the ISP24xx.
Update sysfs NVRAM objects to use generalized accessor
functions.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Generalize SNS generic-services routines.
Consolidate completion-status checking while adding support
for the ISP24xx.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add ISP24xx diagnostic routines.
Add function and structure definitions for the ISP24xx
diagnostic firmware dump routines.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add ISP24xx definitions.
Add requisite structure definitions and #define's for ISP24xx
support. Also drop volatile modifiers from device_reg_* register
layouts as the members are never really accessed, only their
offsets within the layout are used during reads and writes.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add pci ids for new ISP types.
Move old definitions in local qla_def.h file to pci_ids.h as
well.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Factor-out ISP specific functions to method-based call tables.
In anticipation of ISP24xx/ISP25xx support, factor-out ISP
specific functions into a method-based call table.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Linus Torvalds
Chen, Kenneth W
James.Smart@Emulex.Com
Andrew Vasquez
Mark Haverkamp