Fix the runtime suspend issues result from the linking change.
Case 1:
a) link down occurs.
b) driver disable tx/rx.
c) autosuspend occurs.
d) hw linking up.
e) device suspends without enabling tx/rx.
f) couldn't wake up when receiving packets.
Case 2:
a) Nway results in linking down.
b) autosuspend occurs.
c) device suspends.
d) device may not wake up when linking up.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split DRIVER_VERSION into NETNEXT_VERSION and NET_VERSION. Then,
according to the value of DRIVER_VERSION, we could know which
patches are used generally without comparing the source code.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The race may happen when a device (e.g. YOTA 4G LTE Modem) is
unplugged while the system is downloading a large file from the Net.
Hardware breakpoints and Kprobes with delays were used to confirm that
the race does actually happen.
The race is on skb_queue ('next' pointer) between usbnet_stop()
and rx_complete(), which, in turn, calls usbnet_bh().
Here is a part of the call stack with the code where the changes to the
queue happen. The line numbers are for the kernel 4.1.0:
*0 __skb_unlink (skbuff.h:1517)
prev->next = next;
*1 defer_bh (usbnet.c:430)
spin_lock_irqsave(&list->lock, flags);
old_state = entry->state;
entry->state = state;
__skb_unlink(skb, list);
spin_unlock(&list->lock);
spin_lock(&dev->done.lock);
__skb_queue_tail(&dev->done, skb);
if (dev->done.qlen == 1)
tasklet_schedule(&dev->bh);
spin_unlock_irqrestore(&dev->done.lock, flags);
*2 rx_complete (usbnet.c:640)
state = defer_bh(dev, skb, &dev->rxq, state);
At the same time, the following code repeatedly checks if the queue is
empty and reads these values concurrently with the above changes:
*0 usbnet_terminate_urbs (usbnet.c:765)
/* maybe wait for deletions to finish. */
while (!skb_queue_empty(&dev->rxq)
&& !skb_queue_empty(&dev->txq)
&& !skb_queue_empty(&dev->done)) {
schedule_timeout(msecs_to_jiffies(UNLINK_TIMEOUT_MS));
set_current_state(TASK_UNINTERRUPTIBLE);
netif_dbg(dev, ifdown, dev->net,
"waited for %d urb completions\n", temp);
}
*1 usbnet_stop (usbnet.c:806)
if (!(info->flags & FLAG_AVOID_UNLINK_URBS))
usbnet_terminate_urbs(dev);
As a result, it is possible, for example, that the skb is removed from
dev->rxq by __skb_unlink() before the check
"!skb_queue_empty(&dev->rxq)" in usbnet_terminate_urbs() is made. It is
also possible in this case that the skb is added to dev->done queue
after "!skb_queue_empty(&dev->done)" is checked. So
usbnet_terminate_urbs() may stop waiting and return while dev->done
queue still has an item.
Locking in defer_bh() and usbnet_terminate_urbs() was revisited to avoid
this race.
Signed-off-by: Eugene Shatokhin <eugene.shatokhin@rosalab.ru>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/usb/lan78xx.c: In function ‘lan78xx_link_reset’:
net/usb/lan78xx.c:1107: warning: comparison is always false due to limited range of data type
net/usb/lan78xx.c:1111: warning: comparison is always false due to limited range of data type
Assigning return values that can be negative error codes to "u16"
variables makes them positive, ignoring the errors. Hence use "int"
instead.
Drop the "unlikely"s (unlikely considered harmful) and propagate the
actual error values instead of overriding them to -EIO while we're at
it.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is needed to check EVENT_NO_RUNTIME_PM bit of dev->flags in
usbnet_stop(), but its value should be read before it is cleared
when dev->flags is set to 0.
The problem was spotted and the fix was provided by
Oliver Neukum <oneukum@suse.de>.
Signed-off-by: Eugene Shatokhin <eugene.shatokhin@rosalab.ru>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/s390/net/bpf_jit_comp.c
drivers/net/ethernet/ti/netcp_ethss.c
net/bridge/br_multicast.c
net/ipv4/ip_fragment.c
All four conflicts were cases of simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The UEFI driver would enable zero length, and the Linux driver doesn't
need it. Zero length let the hw complete the transfer with length 0,
when there is no received packet. It would add the load of USB host
controller and reduce the performance.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Repost patch of driver for LAN7800 family of USB 2.0 & USB 3.0 to Gigabit Ethernet.
- remove module param which can be configurable by standard mechanism.
- remove other module parms except msg_level per review comment.
- update to handle byte swap for statistics structure correctly.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device reset is necessary if the hw becomes abnormal and stops
transmitting packets.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add rtl8152_pre_reset() and rtl8152_post_reset() which are used when
calling usb_reset_device(). The two functions could reduce the time
of reset when calling usb_reset_device() after probe().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust napi_disable() and napi_enable() to avoid r8152_poll() start
working before rx ready. Otherwise, it may have race condition for
rx_agg.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid the driver to enable WOL if the device doesn't support it.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Disable U1/U2 during initialization.
- Disable lpm when linking is on, and enable it when linking is off.
- Disable U1/U2 when enabling runtime suspend.
It is possible to let hw stop working, if the U1/U2 request occurs
during some situations. The patch is used to avoid it.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/bridge/br_mdb.c
br_mdb.c conflict was a function call being removed to fix a bug in
'net' but whose signature was changed in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Added the USB IDs 0x413c:0x81b1 for the "Dell Wireless 5809e Gobi(TM) 4G
LTE Mobile Broadband Card", a Dell-branded Sierra Wireless EM7305 LTE
card in M.2 form factor, used eg. in Dell's Latitude E7540 Notebook
series.
Signed-off-by: Pieter Hollants <pieter@hollants.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sierra Wireless MC7305/MC7355 with USB ID 1199:9041 also provide a
second QMI/network interface like the MC73xx with USB ID 1199:68c0 on
USB interface #10 when used in the appropriate USB configuration.
Add the corresponding QMI_FIXED_INTF entry to the qmi_wwan driver.
Please note that the second QMI/network interface is not working for
early MC73xx firmware versions like 01.08.x as the device does not
respond to QMI messages on the second /dev/cdc-wdm port.
Signed-off-by: Reinhard Speyerer <rspmn@arcor.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update referenced specs link to reflect actual file version and location.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NCM specs are not actually mandating a specific position in the frame for
the NDP (Network Datagram Pointer). However, some Huawei devices will
ignore our aggregates if it is not placed after the datagrams it points
to. Add support for doing just this, in a per-device configurable way.
While at it, update NCM subdrivers, disabling this functionality in all of
them, except in huawei_cdc_ncm where it is enabled instead.
We aren't making any distinction between different Huawei NCM devices,
based on what the vendor driver does. Standard NCM devices are left
unaffected: if they are compliant, they should be always usable, still
stay on the safe side.
This change has been tested and working with a Huawei E3131 device (which
works regardless of NDP position), a Huawei E3531 (also working both
ways) and an E3372 (which mandates NDP to be after indexed datagrams).
V1->V2:
- corrected wrong NDP acronym definition
- fixed possible NULL pointer dereference
- patch cleanup
V2->V3:
- Properly account for the NDP size when writing new packets to SKB
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hayeswang
Eugene Shatokhin
Geert Uytterhoeven
David Ward
David S. Miller
Woojung.Huh@microchip.com
Pieter Hollants
Reinhard Speyerer
Enrico Mioso