The struct mlx4_interface.event() method was supposed to get an enum
mlx4_dev_event, but the driver code was actually passing in the
hardware enum mlx4_event values. Fix up the callers of
mlx4_dispatch_event() so that they pass in the right type of value,
and fix up the event method in mlx4_ib so that it can handle the enum
mlx4_dev_event values.
This eliminates the need for the subtype parameter to the event
method, so remove it.
This also fixes the sparse warning
drivers/net/mlx4/intf.c:127:48: warning: mixing different enum types
drivers/net/mlx4/intf.c:127:48: int enum mlx4_event versus
drivers/net/mlx4/intf.c:127:48: int enum mlx4_dev_event
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Currently mlx4_ib_fmr_alloc() calls mlx4_mr_enable() instead of
mlx4_fmr_enable(). The two functions are equivalent at the moment, but
this is not really correct (and the change is needed to fix a bug).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ConnectX HCA supports shrinking WQEs, so that a single work request
can be made of multiple units of wqe_shift. This way, WRs can differ
in size, and do not have to be a power of 2 in size, saving memory and
speeding up send WR posting. Unfortunately, if we do this then the
wqe_index field in CQEs can't be used to look up the WR ID anymore, so
our implementation does this only if selective signaling is off.
Further, on 32-bit platforms, we can't use vmap() to make the QP
buffer virtually contigious. Thus we have to use constant-sized WRs to
make sure a WR is always fully within a single page-sized chunk.
Finally, we use WRs with the NOP opcode to avoid wrapping around the
queue buffer in the middle of posting a WR, and we set the
NoErrorCompletion bit to avoid getting completions with error for NOP
WRs. However, NEC is only supported starting with firmware 2.2.232,
so we use constant-sized WRs for older firmware. And, since MLX QPs
only support SEND, we use constant-sized WRs in this case.
When stamping during NOP posting, do stamping following setting of the
NOP WQE valid bit.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We use struct mlx4_buf for kernel QP, CQ and SRQ buffers, and the code
to look up an entry is duplicated in get_cqe_from_buf() and the QP and
SRQ versions of get_wqe(). Factor this out into mlx4_buf_offset().
This will also make it easier to switch over to using vmap() for buffers.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The string mlx4_ib_version was defined, but never used. Print out the
version once when the first device is initialized.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The firmware QUERY_ADAPTER command does not return vendor_id,
device_id, and revision_id; eliminate these fields from the query.
Initialize the rev_id field of the mlx4 device via init_node_data (MAD
IFC query), as is done in the query_device verb implementation.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Rather than byte-swapping cqe->g_mlpath_rqpn each time we extract a
field from it, byte-swap it once into a temporary variable. This
results in smaller, better code -- eg, on 32-bit x86:
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-5 (-5)
function old new delta
mlx4_ib_poll_cq 1188 1183 -5
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix the value of pkey_index in completions to get a valid value for
GSI QPs. Without this fix, incoming GSI packets on port 2 get an
invalid P_Key index in the completion, which prevents the MAD layer
from sending back a response, which can make the second port of
ConnectX HCAs completely useless.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Because of a typo, mlx4_ib_post_send() takes the same lock rq.lock as
mlx4_ib_post_recv(). Correct the code so the intended sq.lock is
taken when posting a send.
Noticed by Yossi Leybovitch and pointed out by Jack Morgenstein from
Mellanox.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add sanity checks to send queue sizes passed in from userspace. The
minimum sq stride value below is taken from the MT25408 PRM (section
11.10, Table 306, log_sq_stride definition).
Without this check, userspace can submit arbitrarily large/small
values for the number of WQEs and the stride, which can crash the
kernel.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Write MTT entries directly to ICM from the driver (eliminating use of
WRITE_MTT command). This reduces the number of FW commands needed to
register an MR by at least a factor of 2 and speeds up memory
registration significantly. This code will also be used to implement
FMRs.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
display the following device information under /sys/class/infiniband/mlx4_X:
board_id, fw_ver, hw_rev, hca_type.
This patch makes this information available to userspace utilities
such as ibstat and ibv_devinfo.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mlx4_srq_query() returns a big-endian 16-bit value through an int *,
which screws up sparse checking. Fix this so that a CPU-endian value
is returned.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use a __set_data_seg() helper in mlx4_ib_post_recv() too; in addition
to making the code easier to read, this also allows gcc to generate
better code -- on x86_64:
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-8 (-8)
function old new delta
mlx4_ib_post_recv 359 351 -8
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This is an addendum to commit 0e6e7416 ("IB/mlx4: Handle new FW
requirement for send request prefetching"). We also need to handle
prefetch marking properly for S/G segments, or else the HCA may end up
processing S/G segments that are not fully written and end up sending
the wrong data. This can actually cause data corruption in practice,
especially on systems with relatively slow CPUs (where the HCA is more
likely to prefetch while the CPU is in the middle of writing a work
request into memory).
We write S/G segments in reverse order into the WQE, in order to
guarantee that the first dword of all cachelines containing S/G
segments is written last (overwriting the headroom invalidation
pattern). The entire cacheline will thus contain valid data when the
invalidation pattern is overwritten.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
A stray semicolon makes us inadvertently ignore the value of err.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Current code has a cut-and-paste error and returns IB_WC_SEND when it
should return IB_WC_RDMA_READ.
Signed-off-by: Vu Pham <vu@mellanox.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The error handling code at err_wrid in create_qp_common() does not
handle a userspace QP attached to an SRQ correctly, since it ends up
in the else clause of the if statement. This means it tries to
kfree() the uninitialized qp->sq.wrid and qp->rq.wrid pointers. Fix
this so we only free the wrid arrays for kernel QPs.
Pointed out by Michael S. Tsirkin <mst@dev.mellanox.co.il>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Temporarily allocated struct mlx4_qp_context *context is leaked by
several error paths. The patch takes advantage of the return value
'err' being preinitialized to -EINVAL.
Spotted by Coverity (CID 1768).
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Factor code to set remote address, atomic and datagram segments out of
mlx4_ib_post_send() into small helper functions. This doesn't change
the generated code in any significant way, and makes the source easier
on the eyes.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Factor code to set data segment entries out of mlx4_ib_post_send()
into set_data_seg(). This cleans up the code and lets the compiler do
a better job -- on x86_64:
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-16 (-16)
function old new delta
mlx4_ib_post_send 1598 1582 -16
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Roland Dreier
Jack Morgenstein
Dotan Barak
Ilpo Järvinen
Vu Pham
Florin Malita