* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: footbridge: fix clock event support
ARM: footbridge: fix debug macros
ARM: initrd: disable initrds outside of memory
ARM: extend Code: line by one 16-bit quantity for Thumb instructions
ARM: 6955/1: cmpxchg syscall should data abort if page not write
ARM: 6954/1: zImage: fix Thumb2 breakage
ARM: 6953/1: DT: don't try to access physical address zero
ARM: 6949/2: mach-u300: fix compilaton warning in IO accessors
Revert "ARM: 6944/1: mm: allow ASID 0 to be allocated to tasks"
Revert "ARM: 6943/1: mm: use TTBR1 instead of reserved context ID"
davinci: make PCM platform devices static
arm: davinci: Fix fallout from generic irq chip conversion
ARM: 6894/1: mmci: trigger card detect IRQs on falling and rising edges
ARM: 6952/1: fix lockdep warning of "unannotated irqs-off"
ARM: 6951/1: include .bss in memory layout information
ARM: 6948/1: Fix .size directives for __arm{7,9}tdmi_proc_info
ARM: 6947/2: mach-u300: fix compilation error in timer
ARM: 6946/1: vexpress: move v2m clock init to init_early
ARM: mx51/sdma: Check the chip revision in run-time
arm: mxs: include asm/processor.h for cpu_relax()
Right now the card detect IRQ for MMCI is requested without any
flags which will give some default machine-specified IRQ
behaviour. However on the U300 rising+falling edges (such as can
be expected from a simple GPIO to generate when inserting/removing
a card) need to be requested explicitly.
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: Ulf Hansson <ulf.hansson@stericsson.com>
Cc: Sebastian Rasmussen <sebastian.rasmussen@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
eMMC does not handle power off when not in sleep state,
Skip regulator disable during probe when eMMC is
not in known state - state left by bootloader.
Resolves eMMC failure on OMAP4
mmc0: error -110 whilst initialising MMC card
Signed-off-by: Balaji T K <balajitk@ti.com>
Tested-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Acked-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (45 commits)
ARM: 6945/1: Add unwinding support for division functions
ARM: kill pmd_off()
ARM: 6944/1: mm: allow ASID 0 to be allocated to tasks
ARM: 6943/1: mm: use TTBR1 instead of reserved context ID
ARM: 6942/1: mm: make TTBR1 always point to swapper_pg_dir on ARMv6/7
ARM: 6941/1: cache: ensure MVA is cacheline aligned in flush_kern_dcache_area
ARM: add sendmmsg syscall
ARM: 6863/1: allow hotplug on msm
ARM: 6832/1: mmci: support for ST-Ericsson db8500v2
ARM: 6830/1: mach-ux500: force PrimeCell revisions
ARM: 6829/1: amba: make hardcoded periphid override hardware
ARM: 6828/1: mach-ux500: delete SSP PrimeCell ID
ARM: 6827/1: mach-netx: delete hardcoded periphid
ARM: 6940/1: fiq: Briefly document driver responsibilities for suspend/resume
ARM: 6938/1: fiq: Refactor {get,set}_fiq_regs() for Thumb-2
ARM: 6914/1: sparsemem: fix highmem detection when using SPARSEMEM
ARM: 6913/1: sparsemem: allow pfn_valid to be overridden when using SPARSEMEM
at91: drop at572d940hf support
at91rm9200: introduce at91rm9200_set_type to specficy cpu package
at91: drop boot_params and PLAT_PHYS_OFFSET
...
With the addition of the platform device mfd_cell pointer, we can now
cleanly pass the sub device drivers platform data pointers through the
regular device platform_data one, and get rid of mfd_get_data()
Cc: Ian Molton <spyro@f2s.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
ST-Ericsson modified ARM PrimeCell PL180 block has not got
an updated corresponding amba-id, althought the IP block has
changed in db8500v2. The change was done to the datactrl register.
Using the overrided subversion ID, account for this.
Signed-off-by: Philippe Langlais <philippe.langlais@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (75 commits)
mmc: core: eMMC bus width may not work on all platforms
mmc: sdhci: Auto-CMD23 fixes.
mmc: sdhci: Auto-CMD23 support.
mmc: core: Block CMD23 support for UHS104/SDXC cards.
mmc: sdhci: Implement MMC_CAP_CMD23 for SDHCI.
mmc: core: Use CMD23 for multiblock transfers when we can.
mmc: quirks: Add/remove quirks conditional support.
mmc: Add new VUB300 USB-to-SD/SDIO/MMC driver
mmc: sdhci-pxa: Add quirks for DMA/ADMA to match h/w
mmc: core: duplicated trial with same freq in mmc_rescan_try_freq()
mmc: core: add support for eMMC Dual Data Rate
mmc: core: eMMC signal voltage does not use CMD11
mmc: sdhci-pxa: add platform code for UHS signaling
mmc: sdhci: add hooks for setting UHS in platform specific code
mmc: core: clear MMC_PM_KEEP_POWER flag on resume
mmc: dw_mmc: fixed wrong regulator_enable in suspend/resume
mmc: sdhi: allow powering down controller with no card inserted
mmc: tmio: runtime suspend the controller, where possible
mmc: sdhi: support up to 3 interrupt sources
mmc: sdhi: print physical base address and clock rate
...
CMD19 -- The offical way to validate bus widths from the JEDEC spec
does not work on all platforms. Some platforms that use PCI/PCIe
to connect their SD controllers are known to fail.
If the quirk MMC_BUS_WIDTH_TEST is not defined we try to figure out
the bus width by reading the ext_csd at different bus widths and
compare this against the ext_csd read in 1 bit mode. If no ext_csd
is available we default to 1 bit operations.
Code has been tested on mmp2 against 8 bit eMMC and Transcend 2GB
card that is known to not work in 4 bit mode. The physical pins
on the card are not present to support 4 bit operation.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Implements support for multiblock transfers bounded
by SET_BLOCK_COUNT (CMD23).
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
CMD23-prefixed instead of open-ended multiblock transfers
have a performance advantage on some MMC cards.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add a driver for Elan Digital System's VUB300 chip which is a USB
connected SDIO/SDmem/MMC host controller. A VUB300 chip enables a USB 2.0
or USB 1.1 connected host computer to use SDIO/SD/MMC cards without the
need for a directly connected, for example via PCI, SDIO host controller.
Signed-off-by: Anthony F Olech <tony.olech@elandigitalsystems.com>
[cjb: various punctuation and style fixes]
Tested-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
32 Bit DMA/ADMA Access
32 Bit Size
Support ADMA End Descriptor in current chain
(no need for dummy entry)
Signed-off-by: Philip Rakity <prakity@marvell.com>
Tested-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
mmc_rescan_try_freq() tries to init two times with the last frequency.
For example, if host->f_min is 400KHz, we see the message below:
mmc1: mmc_rescan_try_freq: trying to init card at 400000 Hz
mmc1: mmc_rescan_try_freq: trying to init card at 400000 Hz
Andy Ross says that he didn't try this code on a board with an f_min
that exactly matches one of the table entries, which explains why the
bug wasn't detected.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Andy Ross <andy.ross@windriver.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
eMMC voltage change not required for 1.8V. 3.3V and 1.8V vcc
are capable of doing DDR. vccq of 1.8v is not required.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Reviewed-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
eMMC chips do not use CMD11 when changing voltage. Add extra
argument to call to indicate if CMD11 needs to be sent.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Reviewed-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Marvell controller requires 1.8V bit in UHS control register 2
be set when doing UHS. eMMC does not require 1.8V for DDR.
add platform code to handle this.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Reviewed-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Allow platform specific code to set UHS registers if
implementation requires speciial platform specific handling
Signed-off-by: Philip Rakity <prakity@marvell.com>
Reviewed-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Since the MMC_PM_KEEP_POWER flag should be set on each suspend,
it should also cleared on each resume.
Upon resuming, we have to know if power was kept
(for re-initialization, etc.), so clear it just after resuming.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Supply a link to TMIO private data for platforms to implement their
own card detection.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The TMIO MMC controller cannot be powered off to save power, when no
card is plugged in, because then it will not be able to detect a new
card-insertion event. On some implementations, however, it is
possible to switch to using another source to detect card insertion.
This patch adds support for such implementations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Convert the SDHI code to support more than a single interrupt source.
Needed to support hardware that uses GIC instead of INTC as interrupt
controller.
Will also allow us to remove the irq forwarding workaround from the
INTC code in the future.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Linus Torvalds
Linus Walleij
Balaji T K
Samuel Ortiz
Philippe Langlais
Philip Rakity
Andrei Warkentin
Tony Olech
Jaehoon Chung
Eliad Peller
Guennadi Liakhovetski
Magnus Damm