The f75375s driver crashes the kernel if it detects an an internal
implementation error. While the detected conditions suggest that
there is a bug in the code, the condition is not fatal.
Replace BUG() with WARN().
Cc: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
SENSORS_LIMIT and the generic clamp_val have the same functionality,
and clamp_val is more efficient.
This patch reduces text size by 9052 bytes and bss size by 11624 bytes
for x86_64 builds.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: George Joseph <george.joseph@fairview5.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Convert to use devm_ functions to reduce code size and simplify the code.
Cc: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In some configurations, BUG() does not result in an endless loop but returns to
the caller. This results in the following compiler warning:
drivers/hwmon/f75375s.c: In function 'duty_mode_enabled':
drivers/hwmon/f75375s.c:280: warning: control reaches end of non-void function
drivers/hwmon/f75375s.c: In function 'auto_mode_enabled':
drivers/hwmon/f75375s.c:295: warning: control reaches end of non-void function
Fix the warning by returning something sensible after BUG().
Cc: Nikolaus Schulz <schulz@macnetix.de>
Cc: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
It makes no sense to attempt to manually configure the fan in auto mode,
or set the duty cycle directly in closed loop mode. The corresponding
registers are then read-only. If the user tries it nonetheless, error out
with EINVAL instead of silently doing nothing.
Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
[guenter.roeck@ericsson.com: Minor formatting cleanup]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The F75387 supports automatic fan control using either PWM duty cycle or
RPM speed values. Make the driver detect the latter mode, and expose the
different modes in sysfs as per pwm_enable, so that the user can switch
between them.
The interpretation of the pwm_enable attribute for the F75387 is adjusted
to be a superset of those values used for similar Fintek chips which do
not support automatic duty mode, with 2 mapping to automatic speed mode,
and moving automatic duty mode to the new value 4.
Toggling the duty mode via pwm_enable is currently denied for the F75387,
as the chip then simply reinterprets the fan configuration register values
according to the new mode, switching between RPM and PWM units, which
makes this a dangerous operation.
This patch introduces a new pwm mode into the driver. This is necessary
because the new mode (automatic pwm mode, 4) may already be enabled by the
BIOS, and the driver should not break existing functionality. This was seen
on at least one board.
Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
For the F75387, the register holding the current PWM duty cycle value is
r/o; changing it requires writing to the fan expect register instead.
Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
[guenter.roeck@ericsson.com: Simplified function parameters]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
By hwmon sysfs interface convention, setting pwm_enable to zero sets a fan
to full speed. In the f75375s driver, this need be done by enabling
manual fan control, plus duty mode for the F875387 chip, and then setting
the maximum duty cycle. Fix a bug where the two necessary register writes
were swapped, effectively discarding the setting to full-speed.
Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
Cc: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Treat pwmX as a measured value, not as a (mostly static) limit value, so
that it is updated more frequently from the device register.
Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Unlike the other chips supported by this driver, the F75387 stores the
pwm_mode in register F75375_REG_FAN_TIMER, not F75375_REG_CONFIG1.
Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
In order to enable temperature mode aka automatic mode for the F75373 and
F75375 chips, the two FANx_MODE bits in the fan configuration register
need be set to 01, not 10.
Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
Cc: stable@kernel.org # 2.6.32+
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Fintek F75387SG/RG is mostly compatible to F75373/F75375. Add support for it
to the F75375S driver.
Fan support for F75387SG/RG has been implemented but not tested.
Cc: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Bjoern Gerhart <oss@extracloud.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
pwmX_mode and pwmX_enable are not initialized if no platform data is provided to
the driver. Read chip configuration at driver initialization time and initialize
attributes to reflect chip configuration.
Cc: Riku Voipio <riku.voipio@iki.fi>
Reviewed-by: Bjoern Gerhart <oss@extracloud.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Accepted value range for PWM modes was 0..4, even though only 0..3 is
subsequently used. Limit permitted value range to 0..3 to avoid unpredictable
behavior.
Cc: Riku Voipio <riku.voipio@iki.fi>
Reviewed-by: Bjoern Gerhart <oss@extracloud.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The driver uses non-standard sysfs attribute names for maximum and target fan
speeds, even though standard attibute names for the same values do exist.
Replace non-standard attribute names with standard attribute names.
Cc: Riku Voipio <riku.voipio@iki.fi>
Reviewed-by: Bjoern Gerhart <oss@extracloud.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
All bits in the values read from registers to be used for the next
write were getting overwritten, avoid doing so to not mess with the
current configuration.
Signed-off-by: Guillem Jover <guillem@hadrons.org>
Cc: Riku Voipio <riku.voipio@iki.fi>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The spec notes that fan0 and fan1 control mode bits are located in bits
7-6 and 5-4 respectively, but the FAN_CTRL_MODE macro was making the
bits shift by 5 instead of by 4.
Signed-off-by: Guillem Jover <guillem@hadrons.org>
Cc: Riku Voipio <riku.voipio@iki.fi>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Guenter Roeck
Jingoo Han
Axel Lin
Nikolaus Schulz
Nikolaus Schulz
Björn Gerhart
Guenter Roeck
Linus Torvalds
Justin P. Mattock
Guillem Jover