With spidev the mesg->complete callback points to spidev_complete.
Calling this unblocks spidev_sync and so spidev_sync_write finishes. As
the struct spi_message just read is a local variable in
spidev_sync_write and recording the trace event accesses this message
the recording is better done first. The same can happen for
spidev_sync_read.
This fixes an oops observed on a 3.14-rt system with spidev activity
after
echo 1 > /sys/kernel/debug/tracing/events/spi/enable
.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The logic of DMA completion is broken now since test_and_clear_bit() never
returns the other bit is set. It means condition are always false and we have
spi_finalize_current_transfer() called per each DMA completion which is wrong.
The patch fixes logic by clearing BUSY bit first and then check for the other
one.
Fixes: 30c8eb52cc (spi: dw-mid: split rx and tx callbacks when DMA)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Commit fd316941c ("spi/pl022: disable port when unused") introduced a race,
which leads to possible driver lock up (easily reproducible on SMP).
The problem happens in giveback() function where the completion of the transfer
is signalled to SPI subsystem and then the HW SPI controller is disabled. Another
transfer might be setup in between, which brings driver in locked-up state.
Exact event sequence on SMP:
core0 core1
=> pump_transfers()
/* message->state == STATE_DONE */
=> giveback()
=> spi_finalize_current_message()
=> pl022_unprepare_transfer_hardware()
=> pl022_transfer_one_message
=> flush()
=> do_interrupt_dma_transfer()
=> set_up_next_transfer()
/* Enable SSP, turn on interrupts */
writew((readw(SSP_CR1(pl022->virtbase)) |
SSP_CR1_MASK_SSE), SSP_CR1(pl022->virtbase));
...
=> pl022_interrupt_handler()
=> readwriter()
/* disable the SPI/SSP operation */
=> writew((readw(SSP_CR1(pl022->virtbase)) &
(~SSP_CR1_MASK_SSE)), SSP_CR1(pl022->virtbase));
Lockup! SPI controller is disabled and the data will never be received. Whole
SPI subsystem is waiting for transfer ACK and blocked.
So, only signal transfer completion after disabling the controller.
Fixes: fd316941c (spi/pl022: disable port when unused)
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
When DMA descriptor allocation fails we should not try to assign any fields in
the bad descriptor. The patch adds the necessary checks for that.
Fixes: 7063c0d942 (spi/dw_spi: add DMA support)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Maximum transfer length supported by SPFI is 65535, this is limited
by the number of bits available in SPFI TSize register to represent
the transfer size.
For transfer requests larger than the maximum supported the driver
will return an invalid argument error.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Additionally to the current DMA transfer the PDC allows to set up a next DMA
transfer. This is useful for larger SPI transfers.
The driver currently waits for ENDRX as end of the transfer. But ENDRX is set
when the current DMA transfer is done (RCR = 0), i.e. it doesn't include the
next DMA transfer.
Thus a subsequent SPI transfer could be started although there is currently a
transfer in progress. This can cause invalid accesses to the SPI slave devices
and to SPI transfer errors.
This issue has been observed on a hardware with a M25P128 SPI NOR flash.
So instead of ENDRX we should wait for RXBUFF. This flag is set if there is
no more DMA transfer in progress (RCR = RNCR = 0).
Signed-off-by: Torsten Fleischer <torfl6749@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The commit d297933cc7 (spi: dw: Fix detecting FIFO depth) tries to fix the
logic of the FIFO detection based on the description on the comments. However,
there is a slight difference between numbers in TX Level and TX FIFO size.
So, by specification the FIFO size would be in a range 2-256 bytes. From TX
Level prospective it means we can set threshold in the range 0-(FIFO size - 1)
bytes. Hence there are currently two issues:
a) FIFO size 2 bytes is actually skipped since TX Level is 1 bit and could be
either 0 or 1 byte;
b) FIFO size is incorrectly decreased by 1 which already done by meaning of
TX Level register.
This patch fixes it eventually right.
Fixes: d297933cc7 (spi: dw: Fix detecting FIFO depth)
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The commit d58cf5ff65 brought a second controller to the list of supported
devices and changed a number of the chip selects. Besides the previous number
was wrong anyway the mentioned patch makes it wrong again meanwhile has a
proper numbers in the commit message. Indeed, SPI1 has 5 bits and SPI2 has 2
bits, but it does not mean to have power of two of this bits as a possible
number of the chip selects. So, this patch fixes it eventually.
Fixes: d58cf5ff65 (spi: dw-pci: describe Intel MID controllers better)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Data corruption is seen while reading/writing large data from/to qspi
device because the data register is over written or read before data
is ready which is denoted by busy bit in status register. SO adding
a busy bit check before writing/reading data to/from qspi device.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull kconfig updates from Michal Marek:
"Yann E Morin was supposed to take over kconfig maintainership, but
this hasn't happened. So I'm sending a few kconfig patches that I
collected:
- Fix for missing va_end in kconfig
- merge_config.sh displays used if given too few arguments
- s/boolean/bool/ in Kconfig files for consistency, with the plan to
only support bool in the future"
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kconfig: use va_end to match corresponding va_start
merge_config.sh: Display usage if given too few arguments
kconfig: use bool instead of boolean for type definition attributes
Use the normal {} instead of a macro to terminate an array.
Remove the macro too.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
return type of wait_for_completion_timeout is unsigned long not int, this
patch uses the return value of wait_for_completion_timeout in the condition
directly rather than adding a additional appropriately typed variable.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
return type of wait_for_completion_timeout is unsigned long not int, this
patch uses the return value of wait_for_completion_timeout in the condition
directly rather than assigning it to an incorrect type variable.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown
Uwe Kleine-König
Andy Shevchenko
Ivan T. Ivanov
Alexander Sverdlin
Sifan Naeem
Torsten Fleischer
Mugunthan V N
Linus Torvalds
Joe Perches
Nicholas Mc Guire