libata/for-3.10-fixes never got submitted during v3.10 cycle. Merge
it into for-3.11 so that it can be routed together with other changes
scheduled for v3.11.
Three trivial conflicts in drivers/ata/sata_rcar.c. All are caused by
1b20f6a9ad ("sata_rcar: add 'base' local variable to some functions")
conflicting with logic updates in for-3.10-fixes. The offending
commit simply adds local variable @base on functions which
dereferences sata_rcar_priv->base multiple times. The resolutions are
trivial - applying s/priv->base/base/ in the conflicting logic
updates.
Signed-off-by: Tejun Heo <tj@kernel.org>
ahci_hardreset() and ahci_p5wdh_hardreset() use bare numbers for the
BSY bit of the ATA status register, despite it's #define'd in
<linux/ata.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
There are some SATA controllers which have both devices 0 and 1 but this module
just zeroes out taskfile and sets then ATA_TFLAG_DEVICE (not sure that's needed)
which could lead to a wrong device being selected just before issuing command.
Thus we should call ata_tf_init() which sets up the device register value
properly, like all other users of ata_exec_internal() do...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
- Remove duplicate Medium Error Entry.
- Fix translations to match SAT2 translation table.
- Remove warning messages when translation is not found when decoding
error or status register.
- Goes through status register decoding when only ABRT bit is set in
error register.
Tested: When a disk fails, it sets
Status = 0x71 [DRDY DF ERR] , Error = 0x4 [ABRT]
This patch will make the sense key HARDWARE_ERROR instead.
When there is a simple command syntax error:
Status = 0x51 [DRDY ERR] , Error = 0x4 [ABRT]
The sense key remains ABORTED_COMMAND.
tj: Some updates to the description and comments.
Signed-off-by: Gwendal Grignou <gwendal@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch adds the compatible string of the exynos5440 sata controller
compliant with the ahci 1.3 and sata 3.0 specification.
changes in v2:
changed the compatible string by adding the actual IP
owners name instead of the SoC vendor name.
Signed-off-by: Girish K S <ks.giri@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
For some reason, a lot of port-multipliers have issues with softreset.
SIMG [34]7x series port-multipliers have been quite erratic in this
regard. I recall that it was better with some firmware revisions and
the current list of quirks worked fine for a while. I think it got
worse with later firmwares or maybe my test coverage wasn't good
enough. Anyways, HPA is reporting that his 3726 setup suffers SRST
failures and then the PMP gets confused and fails to probe the last
port.
The hope was that we try to stick to the standard as much as possible
and soonish the PMPs and their firmwares will improve in quality, so
the quirk list was kept to minimum. Well, it seems like that's never
gonna happen.
Let's set NO_SRST for all [34]7x PMPs so that whatever remaining
userbase of the device suffer the least. Maybe we should do the same
for 57xx's but unfortunately I don't have any device left to test and
I'm not even sure 57xx's have ever been made widely available, so
let's leave those alone for now.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: "H. Peter Anvin" <hpa@zytor.com>
Cc: stable@vger.kernel.org
Highbank supports SGPIO by bit-banging out the SGPIO signals over
three GPIO pins defined in the DTB. Add support for this SGPIO
functionality.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Create a new ata_port_operations function pointer called
transmit_led_message and give it the default value of
ahci_transmit_led_message. This allows AHCI controllers with
non-standard LED interfaces to use the existing em_ interface.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
When compiling the driver with gcc 4.8, it gives the following warning:
drivers/ata/sata_rcar.c: In function `sata_rcar_thaw':
drivers/ata/sata_rcar.c:183:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
Fix the warning by explicit cast of the 'unsigned long' value to 'u32'.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Increase the retry count for the hard reset function to 100 but
shorten the time out period to 500 ms. See the comment for
ahci_highbank_hardreset for the reasons why those vaulues were
chosen.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Use the wrapper function for getting the driver data using pci_dev
instead of using dev_get_drvdata() with &pdev->dev, so we can directly
pass a struct pci_dev. This is a purely cosmetic change.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The driver's interrupt handling code is too picky in deciding whether it should
handle an interrupt or not which causes completely unneeded spurious interrupts.
Thus make sata_rcar_{ata|serr}_interrupt() *void*; add ATA status register read
to sata_rcar_ata_interrupt() to clear an unexpected ATA interrupt -- it doesn't
get cleared by writing to the SATAINTSTAT register in the interrupt mode we use.
Also, in sata_rcar_ata_interrupt() we should check SATAINTSTAT register only for
enabled interrupts and we should clear only those interrupts that we have read
as active first time around, because else we have a race and risk clearing an
interrupt that can occur between read and write of the SATAINTSTAT register
and never registering it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
A third possible PCI ID, as personally observed, and found in the
pci.ids list.
Signed-off-by: George Spelvin <linux@horizon.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The 'base' field of 'struct sata_rcar_priv' is used very often
throughout the driver, so it seems worth loading it into a local
variable if it's used more than once in a function.
While at it, put some unitialized variables after intialized ones for
aesthetic reasons. :-)
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Using ATA_BMDMA_SHT() to intialize 'sata_rcar_sht' was suboptimal as
the R-Car descriptor table transfer counter is 28 bits wide (bit 1 to
bit 28), so that the 'dma_boundary' field of 0xFFFF is just too small,
as well as the 'sg_tablesize' field of 128. Use ATA_BASE_SHT() to
initialize 'sata_rcar_sht' instead and give proper values to the
'dma_boundary' and 'sg_tablesize' fields explicitly.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
I've modified sata_rcar_bmdma_fill_sg() to take care of splitting long
scatter/ gather segments due to the descriptor table transfer counter
being only 28 bits wide (bit 1 to bit 28) but that was in vain as even
if 'sata_rcar_sht' specified a correct 'dma_boundary' field, the DMA
and block layers would have split the S/G segments on the necassary
boundaries. Since the driver uses ATA_BMDMA_SHT() to initilaize
'sata_rcar_sht', the boundary is much smaller, only 0xFFFF, so the
code I've added is even more useless, and it's better to just remove
it.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The motivation for this is to allow the driver to be
used with the r8a7790 SoC.
I believe that rather than adding another SoC to the list of allowed SoCs
it is better to simply remove the dependency of the driver on shmobile all
together.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Tejun Heo <tj@kernel.org>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Also, unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Currently all interrupts assigned to AHCI ports show up in
'/proc/interrupts' as 'ahci'. This fix adds port numbers as
suffixes and hence makes the descriptions distinct.
Reported-by: Jan Beulich <JBeulich@suse.com>
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Iff bmdma_setup() has to stop a DMA transfer before starting a new
one, then the STOP bit in the ATAPI_CONTROL1 register will remain set
(it's only cleared when setting the START bit to 1) and then
bmdma_start() method will set both START and STOP bits simultaneously
which should abort the transfer being just started. Avoid that by
explicitly clearing the STOP bit in bmdma_start() method (in this case
it will be ignored on write).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Some device require DMADIR to be enabled, but are not detected as such
by atapi_id_dmadir. One such example is "Asus Serillel 2"
SATA-host-to-PATA-device bridge: the bridge itself requires DMADIR,
even if the bridged device does not.
As atapi_dmadir module parameter can cause problems with some devices
(as per Tejun Heo's memory), enabling it globally may not be possible
depending on the hardware.
This patch adds atapi_dmadir in the form of a "force" horkage value,
allowing global, per-bus and per-device control.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Tejun Heo
Sergei Shtylyov
Seth Heasley
Gwendal Grignou
Girish K S
Shane Huang
Mark Langsdorf
Jingoo Han
George Spelvin
Simon Horman
Alexander Gordeev
Vincent Pelletier