Use 'unsigned int' instead of 'unsigned long' in the NAND chip description data
structure, because 32-bits is more than enough for our purposes. We do not need
64-bits, which is what we end up on 64-bit architectures. We declare many
instances of this data structure, so this should help saving some amount of
memory.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Up until now we identified NAND chips by the 'device ID' part of the full chip
ID array, which is the second full ID array byte. However, the newest flashes
use the same device ID for chips with identical page and eraseblock sizes, but
different OOB sizes. And unfortunately, it is not clear if there is a
"standard" way to fetch the OOB size from chip's full ID array. Here is an
example:
Toshiba TC58NVG2S0F: 0x98, 0xdc, 0x90, 0x26, 0x76, 0x15, 0x01, 0x08
Toshiba TC58NVG3S0F: 0x98, 0xd3, 0x90, 0x26, 0x76, 0x15, 0x02, 0x08
The first one is a 512MiB NAND chip with 4KiB NAND pages, 256KiB eraseblock
size and 224 bytes OOB. The second one is a 1GiB NAND chip with the same page
and eraseblock sizes, but with 232 bytes OOB.
This means that we have to store full ID in our NAND flashes table in order to
distinguish between these 2.
This patch adds the 'id[8]' field to the 'struct nand_flash_dev' structure, and
it makes it to be a part of anonymous union, where the second member is a
structure containing the 'mfr_id' and 'dev_id' bytes. The union makes sure that
'mfr_id' refers the same RAM address as 'id[0]' and 'dev_id' refers the same
RAM address as 'id[1]'. The only motivation for the union is an assumption that
'type->dev_id' is more readable than 'type->id[1]'.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Introduce helper macros for defining NAND chips. These macros do not really add
much value in the current code-base. However, we are going to add full ID
support which adds some more complexity to the table, and helper macros become
useful for readability.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The 'id' is a bit confusing name because NAND IDs are multi-byte. Re-name
it to 'dev_id' to make it clear that this is the "device ID" part (the second
byte).
While on it, clean-up the commentary for 'struct nand_flash_dev'.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We have only one AG-AND driver and it was not touched since 2005. It looks
like AG-AND was not really make it to mass-production and can be considered
a dead technology.
Along with the AG-AND support, this patch removes the BBT_AUTO_REFRESH feature,
because the only user of this feature is AG-AND. And even though it is
implemented as a generic feature, I prefer to remove it because NAND flashes do
not really need it in this form.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This partially reverts commit 1696e6bc2a
("mtd: nand: kill NAND_NO_READRDY").
In that patch I overlooked a few things.
The original documentation for NAND_NO_READRDY included "True for all
large page devices, as they do not support autoincrement." I was
conflating "not support autoincrement" with the NAND_NO_AUTOINCR option,
which was in fact doing nothing. So, when I dropped NAND_NO_AUTOINCR, I
concluded that I then could harmlessly drop NAND_NO_READRDY. But of
course the fact the NAND_NO_AUTOINCR was doing nothing didn't mean
NAND_NO_READRDY was doing nothing...
So, NAND_NO_READRDY is re-introduced as NAND_NEED_READRDY and applied
only to those few remaining small-page NAND which needed it in the first
place.
Cc: stable@kernel.org [3.5+]
Reported-by: Alexander Shiyan <shc_work@mail.ru>
Tested-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The driver call nand_scan_ident in 8 bit mode, then
readid or onfi detection are done (and detect bus width).
The driver should update its bus width before calling nand_scan_tail.
This work because readid and onfi are read work 8 byte mode.
Note that nand_scan_ident send command (NAND_CMD_RESET, NAND_CMD_READID, NAND_CMD_PARAM), address and read data
The ONFI specificication is not very clear for x16 device if high byte of address should be driven to 0,
but according to [1] it should be ok to not drive it during autodetection.
[1]
3.3.2. Target Initialization
[...]
The Read ID and Read Parameter Page commands only use the lower 8-bits of the data bus.
The host shall not issue commands that use a word data width on x16 devices until the host
determines the device supports a 16-bit data bus width in the parameter page.
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
add onfi_get_async_timing_mode() to get the supportted asynchronous
timing mode.
add onfi_get_sync_timing_mode() to get the supportted synchronous
timing mode.
Also add the neccessary macros : the timing modes.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Added a NAND device flag for subpage read support. Previously this was
hard coded based on large page and soft ECC.
Updated base NAND driver to use the new subpage read flag if the NAND is
large page and soft ECC.
Signed-off-by: Jeff Westfahl <jeff.westfahl@ni.com>
Reviewed-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Just as Artem suggested:
"Both UBI and JFFS2 are able to read verify what they wrote already.
There are also MTD tests which do this verification. So I think there
is no reason to keep this in the NAND layer, let alone wasting RAM in
the driver to support this feature. Besides, it does not work for sub-pages
and many drivers have it broken. It hurts more than it provides benefits."
So kill MTD_NAND_VERIFY_WRITE entirely.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The NAND_CHIPOPTIONS_MSK has limited utility and is causing real bugs. It
silently masks off at least one flag that might be set by the driver
(NAND_NO_SUBPAGE_WRITE). This breaks the GPMI NAND driver and possibly
others.
Really, as long as driver writers exercise a small amount of care with
NAND_* options, this mask is not necessary at all; it was only here to
prevent certain options from accidentally being set by the driver. But the
original thought turns out to be a bad idea occasionally. Thus, kill it.
Note, this patch fixes some major gpmi-nand breakage.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Huang Shijie <shijie8@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There is an implemention of hardware ECC write page function which may return an
error indication.
For instance, using Atmel HW PMECC to write one page into a nand flash, the hardware
engine will compute the BCH ecc code for this page. so we need read a the
status register to theck whether the ecc code is generated.
But we cannot assume the status register always can be ready, for example,
incorrect hardware configuration or hardware issue, in such case we need
write_page() to return a error code.
Since the definition of 'write_page' function in struct nand_ecc_ctrl is 'void'.
So this patch will:
1. add return 'int' value for 'write_page' function.
2. to be consitent, add return 'int' value for 'write_page_raw' fuctions too.
3. add code to test the return value, and if negative, indicate an
error happend when write page with ECC.
4. fix the compile warning in all impacted nand flash driver.
Note: I couldn't compile-test all of these easily, as some had ARCH dependencies.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
According to its documentation, the NAND_NO_READRDY option is always used
when autoincrement is not supported. Autoincrement support was recently
dropped, so we can drop this options as well (defaulting to "no read ready
check").
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
As of [mtd: nand: remove autoincrement 'sndcmd' code], the
NAND_CMD_READ0 command is issued unconditionally.
Thus, read_oob/read_oob_raw's 'sndcmd' argument is no longer needed, as
well as their return code.
Remove the 'sndcmd' parameter, and set the return code to 0.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Artem Bityutskiy
Brian Norris
Matthieu CASTET
Robert P. J. Day
Huang Shijie
Mike Dunn
Jeff Westfahl
Randy Dunlap
Huang Shijie
Josh Wu
Shmulik Ladkani