This patch introduces 'struct blk_flush_queue' and puts all
flush machinery related fields into this structure, so that
- flush implementation details aren't exposed to driver
- it is easy to convert to per dispatch-queue flush machinery
This patch is basically a mechanical replacement.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
These two temporary functions are introduced for holding flush
initialization and de-initialization, so that we can
introduce 'flush queue' easier in the following patch. And
once 'flush queue' and its allocation/free functions are ready,
they will be removed for sake of code readability.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
It is reasonable to allocate flush req in blk_mq_init_flush().
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Failure of initializing one hctx isn't handled, so this patch
introduces blk_mq_init_hctx() and its pair to handle it explicitly.
Also this patch makes code cleaner.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
blk-mq uses percpu_ref for its usage counter which tracks the number
of in-flight commands and used to synchronously drain the queue on
freeze. percpu_ref shutdown takes measureable wallclock time as it
involves a sched RCU grace period. This means that draining a blk-mq
takes measureable wallclock time. One would think that this shouldn't
matter as queue shutdown should be a rare event which takes place
asynchronously w.r.t. userland.
Unfortunately, SCSI probing involves synchronously setting up and then
tearing down a lot of request_queues back-to-back for non-existent
LUNs. This means that SCSI probing may take above ten seconds when
scsi-mq is used.
[ 0.949892] scsi host0: Virtio SCSI HBA
[ 1.007864] scsi 0:0:0:0: Direct-Access QEMU QEMU HARDDISK 1.1. PQ: 0 ANSI: 5
[ 1.021299] scsi 0:0:1:0: Direct-Access QEMU QEMU HARDDISK 1.1. PQ: 0 ANSI: 5
[ 1.520356] tsc: Refined TSC clocksource calibration: 2491.910 MHz
<stall>
[ 16.186549] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 16.190478] sd 0:0:1:0: Attached scsi generic sg1 type 0
[ 16.194099] osd: LOADED open-osd 0.2.1
[ 16.203202] sd 0:0:0:0: [sda] 31457280 512-byte logical blocks: (16.1 GB/15.0 GiB)
[ 16.208478] sd 0:0:0:0: [sda] Write Protect is off
[ 16.211439] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 16.218771] sd 0:0:1:0: [sdb] 31457280 512-byte logical blocks: (16.1 GB/15.0 GiB)
[ 16.223264] sd 0:0:1:0: [sdb] Write Protect is off
[ 16.225682] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
This is also the reason why request_queues start in bypass mode which
is ended on blk_register_queue() as shutting down a fully functional
queue also involves a RCU grace period and the queues for non-existent
SCSI devices never reach registration.
blk-mq basically needs to do the same thing - start the mq in a
degraded mode which is faster to shut down and then make it fully
functional only after the queue reaches registration. percpu_ref
recently grew facilities to force atomic operation until explicitly
switched to percpu mode, which can be used for this purpose. This
patch makes blk-mq initialize q->mq_usage_counter in atomic mode and
switch it to percpu mode only once blk_register_queue() is reached.
Note that this issue was previously worked around by 0a30288da1
("blk-mq, percpu_ref: implement a kludge for SCSI blk-mq stall during
probe") for v3.17. The temp fix was reverted in preparation of adding
persistent atomic mode to percpu_ref by 9eca80461a ("Revert "blk-mq,
percpu_ref: implement a kludge for SCSI blk-mq stall during probe"").
This patch and the prerequisite percpu_ref changes will be merged
during v3.18 devel cycle.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Christoph Hellwig <hch@infradead.org>
Link: http://lkml.kernel.org/g/20140919113815.GA10791@lst.de
Fixes: add703fda9 ("blk-mq: use percpu_ref for mq usage count")
Reviewed-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Johannes Weiner <hannes@cmpxchg.org>
With the recent addition of percpu_ref_reinit(), percpu_ref now can be
used as a persistent switch which can be turned on and off repeatedly
where turning off maps to killing the ref and waiting for it to drain;
however, there currently isn't a way to initialize a percpu_ref in its
off (killed and drained) state, which can be inconvenient for certain
persistent switch use cases.
Similarly, percpu_ref_switch_to_atomic/percpu() allow dynamic
selection of operation mode; however, currently a newly initialized
percpu_ref is always in percpu mode making it impossible to avoid the
latency overhead of switching to atomic mode.
This patch adds @flags to percpu_ref_init() and implements the
following flags.
* PERCPU_REF_INIT_ATOMIC : start ref in atomic mode
* PERCPU_REF_INIT_DEAD : start ref killed and drained
These flags should be able to serve the above two use cases.
v2: target_core_tpg.c conversion was missing. Fixed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
This reverts commit 0a30288da1, which
was a temporary fix for SCSI blk-mq stall issue. The following
patches will fix the issue properly by introducing atomic mode to
percpu_ref.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Christoph Hellwig <hch@lst.de>
This is to receive 0a30288da1 ("blk-mq, percpu_ref: implement a
kludge for SCSI blk-mq stall during probe") which implements
__percpu_ref_kill_expedited() to work around SCSI blk-mq stall. The
commit reverted and patches to implement proper fix will be added.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Christoph Hellwig <hch@lst.de>
blk-mq uses percpu_ref for its usage counter which tracks the number
of in-flight commands and used to synchronously drain the queue on
freeze. percpu_ref shutdown takes measureable wallclock time as it
involves a sched RCU grace period. This means that draining a blk-mq
takes measureable wallclock time. One would think that this shouldn't
matter as queue shutdown should be a rare event which takes place
asynchronously w.r.t. userland.
Unfortunately, SCSI probing involves synchronously setting up and then
tearing down a lot of request_queues back-to-back for non-existent
LUNs. This means that SCSI probing may take more than ten seconds
when scsi-mq is used.
This will be properly fixed by implementing a mechanism to keep
q->mq_usage_counter in atomic mode till genhd registration; however,
that involves rather big updates to percpu_ref which is difficult to
apply late in the devel cycle (v3.17-rc6 at the moment). As a
stop-gap measure till the proper fix can be implemented in the next
cycle, this patch introduces __percpu_ref_kill_expedited() and makes
blk_mq_freeze_queue() use it. This is heavy-handed but should work
for testing the experimental SCSI blk-mq implementation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Christoph Hellwig <hch@infradead.org>
Link: http://lkml.kernel.org/g/20140919113815.GA10791@lst.de
Fixes: add703fda9 ("blk-mq: use percpu_ref for mq usage count")
Cc: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Tested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Moved blk_mq_rq_timed_out() definition to the private blk-mq.h header.
Signed-off-by: Jens Axboe <axboe@fb.com>
It's not uncommon for crash dump kernels to be limited to 128MB or
something low in that area. This is normally not a problem for
devices as we don't use that much memory, but for some shared SCSI
setups with huge queue depths, it can potentially fill most of
memory with tons of request allocations. blk-mq does scale back
when it fails to allocate memory, but it scales back just enough
so that blk-mq succeeds. This could still leave the system with
not enough memory to make any real progress.
Check if we are in a kdump environment and limit the hardware
queues and tag depth.
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch removes two unnecessary blk_clear_rq_complete(),
the REQ_ATOM_COMPLETE flag is cleared inside blk_mq_start_request(),
so:
- The blk_clear_rq_complete() in blk_flush_restore_request()
needn't because the request will be freed later, and clearing
it here may open a small race window with timeout.
- The blk_clear_rq_complete() in blk_mq_requeue_request() isn't
necessary too, even though REQ_ATOM_STARTED is cleared in
__blk_mq_requeue_request(), in theory it still may cause a small
race window with timeout since the two clear_bit() may be
reordered.
Signed-off-by: Ming Lei <ming.lei@canoical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Allow blk-mq to pass an argument to the timeout handler to indicate
if we're timing out a reserved or regular command. For many drivers
those need to be handled different.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Duplicate the (small) timeout handler in blk-mq so that we can pass
arguments more easily to the driver timeout handler. This enables
the next patch.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Don't do a kmalloc from timer to handle timeouts, chances are we could be
under heavy load or similar and thus just miss out on the timeouts.
Fortunately it is very easy to just iterate over all in use tags, and doing
this properly actually cleans up the blk_mq_busy_iter API as well, and
prepares us for the next patch by passing a reserved argument to the
iterator.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Now that we've changed the driver API on the submission side use the
opportunity to fix up the name on the completion side to fit into the
general scheme.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
When we call blk_mq_start_request from the core blk-mq code before calling into
->queue_rq there is a racy window where the timeout handler can hit before we've
fully set up the driver specific part of the command.
Move the call to blk_mq_start_request into the driver so the driver can start
the request only once it is fully set up.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pass an explicit parameter for the last request in a batch to ->queue_rq
instead of using a request flag. Besides being a cleaner and non-stateful
interface this is also required for the next patch, which fixes the blk-mq
I/O submission code to not start a time too early.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
When requests are retried due to hw or sw resource shortages,
we often stop the associated hardware queue. So ensure that we
restart the queues when running the requeue work, otherwise the
queue run will be a no-op.
Signed-off-by: Jens Axboe <axboe@fb.com>
__blk_mq_alloc_rq_maps() can be invoked multiple times, if we scale
back the queue depth if we are low on memory. So don't clear
set->tags when we fail, this is handled directly in
the parent function, blk_mq_alloc_tag_set().
Reported-by: Robert Elliott <Elliott@hp.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We should not insert requests into the flush state machine from
blk_mq_insert_request. All incoming flush requests come through
blk_{m,s}q_make_request and are handled there, while blk_execute_rq_nowait
should only be called for BLOCK_PC requests. All other callers
deal with requests that already went through the flush statemchine
and shouldn't be reinserted into it.
Reported-by: Robert Elliott <Elliott@hp.com>
Debugged-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch should fix the bug reported in
https://lkml.org/lkml/2014/9/11/249.
We have to initialize at least the atomic_flags and the cmd_flags when
allocating storage for the requests.
Otherwise blk_mq_timeout_check() might dereference uninitialized
pointers when racing with the creation of a request.
Also move the reset of cmd_flags for the initializing code to the point
where a request is freed. So we will never end up with pending flush
request indicators that might trigger dereferences of invalid pointers
in blk_mq_timeout_check().
Cc: stable@vger.kernel.org
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Reported-by: Paulo De Rezende Pinatti <ppinatti@linux.vnet.ibm.com>
Tested-by: Paulo De Rezende Pinatti <ppinatti@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
When we start the request, we set the deadline and flip the bits
marking the request as started and non-complete. However, it's
important that the deadline store is ordered before flipping the
bits, otherwise we could have a small window where the request is
marked started but with an invalid deadline. This can confuse the
timeout handling.
Suggested-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
A bit of churn on the for-linus side that would be nice to have
in the core bits for 3.18, so pull it in to catch us up and make
forward progress easier.
Signed-off-by: Jens Axboe <axboe@fb.com>
Conflicts:
block/scsi_ioctl.c
Ming Lei
Tejun Heo
Christoph Hellwig
Jens Axboe
Ming Lei
David Hildenbrand