* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
b43: fix comment typo reqest -> request
Haavard Skinnemoen has left Atmel
cris: typo in mach-fs Makefile
Kconfig: fix copy/paste-ism for dell-wmi-aio driver
doc: timers-howto: fix a typo ("unsgined")
perf: Only include annotate.h once in tools/perf/util/ui/browsers/annotate.c
md, raid5: Fix spelling error in comment ('Ofcourse' --> 'Of course').
treewide: fix a few typos in comments
regulator: change debug statement be consistent with the style of the rest
Revert "arm: mach-u300/gpio: Fix mem_region resource size miscalculations"
audit: acquire creds selectively to reduce atomic op overhead
rtlwifi: don't touch with treewide double semicolon removal
treewide: cleanup continuations and remove logging message whitespace
ath9k_hw: don't touch with treewide double semicolon removal
include/linux/leds-regulator.h: fix syntax in example code
tty: fix typo in descripton of tty_termios_encode_baud_rate
xtensa: remove obsolete BKL kernel option from defconfig
m68k: fix comment typo 'occcured'
arch:Kconfig.locks Remove unused config option.
treewide: remove extra semicolons
...
The sysfs attribute 'resync_start' (known internally as recovery_cp),
records where a resync is up to. A value of 0 means the array is
not known to be in-sync at all. A value of MaxSector means the array
is believed to be fully in-sync.
When the size of member devices of an array (RAID1,RAID4/5/6) is
increased, the array can be increased to match. This process sets
resync_start to the old end-of-device offset so that the new part of
the array gets resynced.
However with RAID1 (and RAID6) a resync is not technically necessary
and may be undesirable. So it would be good if the implied resync
after the array is resized could be avoided.
So: change 'resync_start' so the value can be changed while the array
is active, and as a precaution only allow it to be changed while
resync/recovery is 'frozen'. Changing it once resync has started is
not going to be useful anyway.
This allows the array to be resized without a resync by:
write 'frozen' to 'sync_action'
write new size to 'component_size' (this will set resync_start)
write 'none' to 'resync_start'
write 'idle' to 'sync_action'.
Also slightly improve some tests on recovery_cp when resizing
raid1/raid5. Now that an arbitrary value could be set we should be
more careful in our tests.
Signed-off-by: NeilBrown <neilb@suse.de>
When a loop ends with an 'if' with a large body, it is neater
to make the if 'continue' on the inverse condition, and then
the body is indented less.
Apply this pattern 3 times, and wrap some other long lines.
Signed-off-by: NeilBrown <neilb@suse.de>
Currently the rdev on which a read error happened could be removed
before we perform the fix_error handling. This requires extra tests
for NULL.
So delay the rdev_dec_pending call until after the call to
fix_read_error so that we can be sure that the rdev still exists.
This allows an 'if' clause to be removed so the body gets re-indented
back one level.
Signed-off-by: NeilBrown <neilb@suse.de>
The current handling and freeing of these pages is a bit fragile.
We only keep the list of allocated pages in each bio, so we need to
still have a valid bio when freeing the pages, which is a bit clumsy.
So simply store the allocated page list in the r1_bio so it can easily
be found and freed when we are finished with the r1_bio.
Signed-off-by: NeilBrown <neilb@suse.de>
If we get a read error during resync/recovery we current repeat with
single-page reads to find out just where the error is, and possibly
read each page from a different device.
With check/repair we don't currently do that, we just fail.
However it is possible that while all devices fail on the large 64K
read, we might be able to satisfy each 4K from one device or another.
So call fix_sync_read_error before process_checks to maximise the
chance of finding good data and writing it out to the devices with
read errors.
For this to work, we need to set the 'uptodate' flags properly after
fix_sync_read_error has succeeded.
Signed-off-by: NeilBrown <neilb@suse.de>
These changes are mostly cosmetic:
1/ change mddev->raid_disks to conf->raid_disks because the later is
technically safer, though in current practice it doesn't matter in
this particular context.
2/ Rearrange two for / if loops to have an early 'continue' so the
body of the 'if' doesn't need to be indented so much.
Signed-off-by: NeilBrown <neilb@suse.de>
sync_request_write is too big and too deep.
So split out two self-contains bits of functionality into separate
function.
Signed-off-by: NeilBrown <neilb@suse.de>
- there is no need to test_bit Faulty, as that was already done in
md_error which is the only caller of these functions.
- MD_CHANGE_DEVS should be set *after* faulty is set to ensure
metadata is updated correctly.
- spinlock should be held while updating ->degraded.
Signed-off-by: NeilBrown <neilb@suse.de>
read_balance has two loops which both look for a 'best'
device based on slightly different criteria.
This is clumsy and makes is hard to add extra criteria.
So replace it all with a single loop that combines everything.
Signed-off-by: NeilBrown <neilb@suse.de>
raid10 read balance has two different loop for looking through
possible devices to chose the best.
Collapse those into one loop and generally make the code more
readable.
Signed-off-by: NeilBrown <neilb@suse.de>
If a bitmap is found to be 'stale' the events_cleared value
is set to match 'events'.
However if the array is degraded this does not get stored on disk.
This can subsequently lead to incorrect behaviour.
So change bitmap_update_sb to always update events_cleared in the
superblock from the known events_cleared.
For neatness also set ->state from ->flags.
This requires updating ->state whenever we update ->flags, which makes
sense anyway.
This is suitable for any active -stable release.
cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
The 'add_new_disk' ioctl can be used to add a device either as a
spare, or as an active disk that just needs to be resynced based on
write-intent-bitmap information (re-add)
Currently if a re-add is requested but fails we add as a spare
instead. This makes it impossible for user-space to check for
failure.
So change to require that a re-add attempt will either succeed or
completely fail. User-space can then decide what to do next.
Signed-off-by: NeilBrown <neilb@suse.de>
There is a race when creating an md device by opening /dev/mdXX.
If two processes do this at much the same time they will follow the
call path
__blkdev_get -> get_gendisk -> kobj_lookup
The first will call
-> md_probe -> md_alloc -> add_disk -> blk_register_region
and the race happens when the second gets to kobj_lookup after
add_disk has called blk_register_region but before it returns to
md_alloc.
In the case the second will not call md_probe (as the probe is already
done) but will get a handle on the gendisk, return to __blkdev_get
which will then call md_open (via the ->open) pointer.
As mddev->gendisk hasn't been set yet, md_open will think something is
wrong an return with ERESTARTSYS.
This can loop endlessly while the first thread makes no progress
through add_disk. Nothing is blocking it, but due to scheduler
behaviour it doesn't get a turn.
So this is essentially a live-lock.
We fix this by simply moving the assignment to mddev->gendisk before
the call the add_disk() so md_open doesn't get confused.
Also move blk_queue_flush earlier because add_disk should be as late
as possible.
To make sure that md_open doesn't complete until md_alloc has done all
that is needed, we take mddev->open_mutex during the last part of
md_alloc. md_open will wait for this.
This can cause a lock-up on boot so Cc:ing for stable.
For 2.6.36 and earlier a different patch will be needed as the
'blk_queue_flush' call isn't there.
Signed-off-by: NeilBrown <neilb@suse.de>
Reported-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Tested-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Cc: stable@kernel.org
There's a small typo in a comment in drivers/md/raid5.c - 'Of course' is
misspelled as 'Ofcourse'. This patch fixes the spelling error.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Change <sectors> from unsigned long long to sector_t.
This matches its source field.
ERROR: "__udivdi3" [drivers/md/raid456.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Problem:
After raid4->raid0 takeover operation, another takeover operation
(e.g raid0->raid10) results "kernel oops".
Root cause:
Variables 'degraded' in mddev structure is not cleared
on raid45->raid0 takeover.
This patch reset this variable.
Signed-off-by: Krzysztof Wojcik <krzysztof.wojcik@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
A raid0 array doesn't set 'dev_sectors' as each device might
contribute a different number of sectors.
So when converting to a RAID4 or RAID5 we need to set dev_sectors
as they need the number.
We have already verified that in fact all devices do contribute
the same number of sectors, so use that number.
Signed-off-by: NeilBrown <neilb@suse.de>
We previously needed to set ->queue_lock to match the raid5
device_lock so we could safely use queue_flag_* operations (e.g. for
plugging). which test the ->queue_lock is in fact locked.
However that need has completely gone away and is unlikely to come
back to remove this now-pointless setting.
Signed-off-by: NeilBrown <neilb@suse.de>
We just need to make sure that an unplug event wakes up the md
thread, which is exactly what mddev_check_plugged does.
Also remove some plug-related code that is no longer needed.
Signed-off-by: NeilBrown <neilb@suse.de>
In raid5 plugging is used for 2 things:
1/ collecting writes that require a bitmap update
2/ collecting writes in the hope that we can create full
stripes - or at least more-full.
We now release these different sets of stripes when plug_cnt
is zero.
Also in make_request, we call mddev_check_plug to hopefully increase
plug_cnt, and wake up the thread at the end if plugging wasn't
achieved for some reason.
Signed-off-by: NeilBrown <neilb@suse.de>
When an md device adds a request to a queue, it can call
mddev_check_plugged.
If this succeeds then we know that the md thread will be woken up
shortly, and ->plug_cnt will be non-zero until then, so some
processing can be delayed.
If it fails, then no unplug callback is expected and the make_request
function needs to do whatever is required to make the request happen.
Signed-off-by: NeilBrown <neilb@suse.de>
Linus Torvalds
NeilBrown
Jesper Juhl
Randy Dunlap
Krzysztof Wojcik