napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dependencies on the architectures that support these devices and
add compile test to ensure ongoing code build coverage.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch disable capturing multicast packets when multicast mode
disabled for ethernet ('ifconfig eth0 -multicast'). In that case
no multicast packet will be passed to kernel.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multicast support was implemented by commit 775dd682e2
('arc_emac: implement promiscuous mode and multicast filtering').
It can be enabled explicity using 'ifconfig eth0 multicast'.
The patch is needed in order to remove explicit configuration
as most devices has multicast mode enabled by default.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace dev_kfree_skb with dev_kfree_skb_any in arc_emac_tx()
which can be called from hard irq context (netpoll) and from
other contexts. arc_emac_tx() only frees skbs that it has
dropped.
This is detected by Coccinelle semantic patch.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We get 1 warning when building kernel with W=1:
drivers/net/ethernet/arc/emac_mdio.c:107:5: warning: no previous prototype for 'arc_mdio_reset' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is
declared and don't need a declaration, but can be made static.
so this patch marks this function with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit a94efbd7cc ("ethernet: arc: emac_main: add missing of_node_put
after calling of_parse_phandle") added missing of_node_put after calling
of_parse_phandle, but missing the devm_ioremap_resource() error handling
case.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a typo in the driver, replace comma with a semicolon at the end
of statement. While using comma is a legal C here and probably does
not even generate compiler warning, it was unlikely the intention.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Caesar Wang <wxt@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
EMAC could be disabled, while there is some sb_buff
in use. That buffers got lost for linux.
In order to reproduce run on device during active ethernet work:
ifconfig eth0 down
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EMAC reset internal tx ring pointer to zero at statup.
txbd_curr and txbd_dirty can be different from zero.
That cause ethernet transfer hang (no packets transmitted).
In order to reproduce, run on device:
ifconfig eth0 down
ifconfig eth0 up
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RK3036's GRFs offset are different with RK3066/RK3188, and need to set
mac TX/RX clock before probe emac.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the RK3066/RK3188, there was fixed GRF offset configuration to set emac
and fixed DIV2 mac TX/RX clock. So, we need to easily set and fit to other
SoCs (RK3036) which maybe have different GRF offset, and need adjust mac
TX/RX clock.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After enter arc_emac_probe, emac will get_phy_id, phy_poll_reset and
other connecting PHY via mdiobus_read, so we need to set correct
ref clock rate for emac before probe emac.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This howto made sense in the 1990s when users had to manually configure
ISA cards with jumpers or vendor utilities, but with the implementation
of PCI it became increasingly less and less relevant, to the point where
it has been well over a decade since I last updated it. And there is
no value in anyone else taking over updating it either.
However the references to it continue to spread as boiler plate text
from one Kconfig file into the next. We are not doing end users any
favours by pointing them at this old document, so lets kill it with
fire, once and for all, to hopefully stop any further spread.
No code is changed in this commit, just Kconfig help text.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If NO_DMA=y:
drivers/built-in.o: In function `arc_emac_tx_clean':
emac_main.c:(.text+0x2decde): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `arc_emac_rx':
emac_main.c:(.text+0x2dee1c): undefined reference to `dma_unmap_single'
emac_main.c:(.text+0x2dee72): undefined reference to `dma_map_single'
emac_main.c:(.text+0x2dee7e): undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `arc_emac_probe':
(.text+0x2df2ee): undefined reference to `dmam_alloc_coherent'
drivers/built-in.o: In function `arc_emac_open':
emac_main.c:(.text+0x2df6d8): undefined reference to `dma_map_single'
emac_main.c:(.text+0x2df6e4): undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `arc_emac_tx':
emac_main.c:(.text+0x2df9e4): undefined reference to `dma_map_single'
emac_main.c:(.text+0x2df9f0): undefined reference to `dma_mapping_error'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/mips/net/bpf_jit.c
drivers/net/can/flexcan.c
Both the flexcan and MIPS bpf_jit conflicts were cases of simple
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the logic in tx path to ensure that tx descriptors
are reused for transmission only after they have been reclaimed by
arc_emac_tx_clean().
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet
Peter Robinson
David S. Miller
Alexander Kochetkov
Wei Yongjun
Baoyou Xie
Wei Yongjun
Peter Chen
Philippe Reynes
Marek Vasut
Caesar Wang
Xing Zheng
Luis de Bethencourt
Paul Gortmaker
Geert Uytterhoeven
Beniamino Galvani