Pull MFD updates from Lee Jones:
"Changes to existing drivers:
- Use of managed resources - omap, twl4030, ti_am335x_tscadc
- Advanced error handling - omap
- Rework clk management - omap
- Device Tree (re-)work - tc3589x, pm8921, da9055, sec
- IRC management overhaul and !BROKEN - pm8921
- Convert to regmap - ssbi, pm8921
- Use simple power-management ops - ucb1x00
- Include file clean-up - adp5520, cs5535, janz, lpc_ich,
- lpc_sch, max14577, mcp-sa11x0, pcf50633-adc, rc5t583,
rdc321x-southbridge, retu, smsc-ece1099, ti-ssp, ti_am335x_tscadc,
tps65912, vexpress-config, wm8350, ywm8350
- Various bug fixes across the subsystem
- NULL/invalid pointer dereference prevention
- Resource leak mitigation,
- Variable used initialised
- Staticise various containers
- Enforce return value checks
New drivers/supported devices:
- Add support for s2mps14 and s2mpa01 to sec
- Add support for da9063 (v5) to da9063
- Add support for atom-c2000 to gpio-ich
- Add support for come-{mbt10,cbt6,chl6} to kempld
- Add support for da9053 to da9052
- Add support for itco-wdt (v3) and baytrail to lpc_ich
- Add new drivers for tps65218, rtsx_usb, bcm590xx
(Re-)moved drivers:
- twl4030 ==> drivers/iio
- ti-ssp ==> /dev/null"
* tag 'mfd-for-linus-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (103 commits)
mfd: wm5110: Correct default for HEADPHONE_DETECT_1
mfd: arizona: Correct small errors in the DT binding documentation
mfd: arizona: Mark DSP clocking register as volatile
mfd: devicetree: bindings: Add pm8xxx RTC description
mfd: kempld-core: Fix potential hang-up during boot
mfd: sec-core: Fix uninitialized 'regmap_rtc' on S2MPA01
mfd: tps65910: Fix regmap_irq_chip_data leak on mfd_add_devices fail
mfd: tps65910: Fix possible invalid pointer dereference on regmap_add_irq_chip fail
mfd: sec-core: Fix I2C dummy device resource leak on probe failure
mfd: sec-core: Add of_compatible strings for clock MFD cells
mfd: Remove obsolete ti-ssp driver
Documentation: mfd: s2mps11: Describe S5M8767 and S2MPS14 clocks
mfd: bcm590xx: Fix type argument for module device table
mfd: lpc_ich: Add support for Intel Bay Trail SoC
mfd: lpc_ich: Add support for NM10 GPIO
mfd: lpc_ich: Change Avoton to iTCO v3
watchdog: iTCO_wdt: Add support for v3 silicon
mfd: lpc_ich: Add support for iTCO v3
mfd: lpc_ich: Remove lpc_ich_cfg struct use
mfd: lpc_ich: Only configure watchdog or GPIO when present
...
Pull HID updates from Jiri Kosina:
- substantial cleanup of the generic and transport layers, in the
direction of an ultimate goal of making struct hid_device completely
transport independent, by Benjamin Tissoires
- cp2112 driver from David Barksdale
- a lot of fixes and new hardware support (Dualshock 4) to hid-sony
driver, by Frank Praznik
- support for Win 8.1 multitouch protocol by Andrew Duggan
- other smaller fixes / device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (75 commits)
HID: sony: fix force feedback mismerge
HID: sony: Set the quriks flag for Bluetooth controllers
HID: sony: Fix Sixaxis cable state detection
HID: uhid: Add UHID_CREATE2 + UHID_INPUT2
HID: hyperv: fix _raw_request() prototype
HID: hyperv: Implement a stub raw_request() entry point
HID: hid-sensor-hub: fix sleeping function called from invalid context
HID: multitouch: add support for Win 8.1 multitouch touchpads
HID: remove hid_output_raw_report transport implementations
HID: sony: do not rely on hid_output_raw_report
HID: cp2112: remove the last hid_output_raw_report() call
HID: cp2112: remove various hid_out_raw_report calls
HID: multitouch: add support of other generic collections in hid-mt
HID: multitouch: remove pen special handling
HID: multitouch: remove registered devices with default behavior
HID: hidp: Add a comment that some devices depend on the current behavior of uniq
HID: sony: Prevent duplicate controller connections.
HID: sony: Perform a boundry check on the sixaxis battery level index.
HID: sony: Fix work queue issues
HID: sony: Fix multi-line comment styling
...
Pull staging driver updates from Greg KH:
"Here's the huge drivers/staging/ update for 3.15-rc1.
Loads of cleanup fixes, a few drivers removed, and some new ones
added.
All have been in linux-next for a while"
* tag 'staging-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1375 commits)
staging: xillybus: XILLYBUS_PCIE depends on PCI_MSI
staging: xillybus: Added "select CRC32" for XILLYBUS in Kconfig
staging: comedi: poc: remove obsolete driver
staging: unisys: replace kzalloc/kfree with UISMALLOC/UISFREE
staging: octeon-usb: prevent memory corruption
staging: usbip: fix line over 80 characters
staging: usbip: fix quoted string split across lines
Staging: unisys: Remove RETINT macro
Staging: unisys: Remove FAIL macro
Staging: unisys: Remove RETVOID macro
Staging: unisys: Remove RETPTR macro
Staging: unisys: Remove RETBOOL macro
Staging: unisys: Remove FAIL_WPOSTCODE_1 macro
Staging: unisys: Cleanup macros to get rid of goto statements
Staging: unisys: include: Remove unused macros from timskmod.h
staging: dgap: fix the rest of the checkpatch warnings in dgap.c
Staging: bcm: Remove unnecessary parentheses
staging: wlags49_h2: Delete unnecessary braces
staging: wlags49_h2: Do not use assignment in if condition
staging: wlags49_h2: Enclose macro in a do-while loop
...
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is a driver for an A/D converter, which belongs into
drivers/iio/adc.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Jonathan writes:
Third IIO new drivers and cleanups series for 3.15.
New driver
* Xilinx XADC driver - This has been ready for a while but was awaiting
a device tree ack (or as it turns out 3+ weeks).
Cleanup
* Drop some unreachable code from mag3110 highlighted by smatch.
Fix
* vf610 - introduced this cycle - put a possible negative error code
into an unsigned long. Another smatch find - this one promoted by
guilt that Dan was busy fixing all our messups.
Issue highlighted by smatch warning:
CHECK drivers/iio/adc/vf610_adc.c
drivers/iio/adc/vf610_adc.c:466 vf610_read_raw() warn: unsigned 'ret' is never less than zero.
As wait_for_completion_interruptible_timeout can return -ERESTARTSTSYS, if
interrupted, ret must be signed.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Fugang Duan <B38611@freescale.com>
The Xilinx XADC is a ADC that can be found in the series 7 FPGAs from Xilinx.
The XADC has a DRP interface for communication. Currently two different
frontends for the DRP interface exist. One that is only available on the ZYNQ
family as a hardmacro in the SoC portion of the ZYNQ. The other one is available
on all series 7 platforms and is a softmacro with a AXI interface. This driver
supports both interfaces and internally has a small abstraction layer that hides
the specifics of these interfaces from the main driver logic.
The ADC has a couple of internal channels which are used for voltage and
temperature monitoring of the FPGA as well as one primary and up to 16 channels
auxiliary channels for measuring external voltages. The external auxiliary
channels can either be directly connected each to one physical pin on the FPGA
or they can make use of an external multiplexer which is responsible for
multiplexing the external signals onto one pair of physical pins.
The voltage and temperature monitoring channels also have an event capability
which allows to generate a interrupt when their value falls below or raises
above a set threshold.
Buffered sampling mode is supported by the driver, but only for AXI-XADC since
the ZYNQ XADC interface does not have capabilities for supporting buffer mode
(no end-of-conversion interrupt). If buffered mode is supported the driver will
register two triggers. One "xadc-samplerate" trigger which will generate samples
with the configured samplerate. And one "xadc-convst" trigger which will
generate one sample each time the CONVST (conversion start) signal is asserted.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The event code currently holds a spinlock with IRQs disabled while calling
kfifo_to_user(). kfifo_to_user() can generate a page fault though, which means
we have to be able to sleep, which is not possible if the interrupts are
disabled. The good thing is that kfifo handles concurrent read and write access
just fine as long as there is only one reader and one writer, so we do not any
locking to protect against concurrent access from the read and writer thread. It
is possible though that userspace is trying to read from the event FIFO from
multiple concurrent threads, so we need to add locking to protect against this.
This is done using a mutex. The mutex will only protect the kfifo_to_user()
call, it will not protect the waitqueue. This means that multiple threads can be
waiting for new data and once a new event is added to the FIFO all waiting
threads will be woken up. If one of those threads is unable to read any data
(because another thread already read all the data) it will go back to sleep. The
only remaining issue is that now that the clearing of the BUSY flag and the
emptying of the FIFO does no longer happen in one atomic step it is possible
that a event is added to the FIFO after it has been emptied and this sample will
be visible the next time a new event file descriptor is created. To avoid this
rather move the emptying of the FIFO from iio_event_chrdev_release to
iio_event_getfd().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds support for the new barometer sensor: LPS25H.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added usage id processing for Pressure Sensor. This uses IIO
interfaces for triggered buffer to present data to user
mode. This uses HID sensor framework for registering callback
events from the sensor hub.
Signed-off-by: Archana Patni <archana.patni@intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added usage id processing for Proximity (Human Presence).
This uses IIO interfaces for triggered buffer to present data
to user mode. This uses HID sensor framework for registering
callback events from the sensor hub.
Signed-off-by: Archana Patni <archana.patni@intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
name_format already contains the final name and no format characters. So the
code basically reads:
dev_attr->attr.name = kstrdup(GFP_KERNEL, name_format);
if (dev_attr->attr.name == NULL)
...
kfree(name_format);
Which means we can save one alloc and free pair per attribute name if we
directly assign name_format to dev_attr->attr.name.
The patch also renames name_format to name to denote that this is indeed the
final name and has no format characters in it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The extended name is channel specific and should not be included in shared
attributes.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver was not able to manage the sensor: during probe function
and wai check, the driver stops and writes: "device name and WhoAmI mismatch."
The correct value of L3GD20H wai is 0xd7 instead of 0xd4.
Dropped support for the sensor.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Integration time of cm32181 is guessed about milliseconds.
But cm32181_read_als_it function return IIO_VAL_INT.
So fixed to return IIO_VAL_INT_PLUS_MICRO.
Next, add .write_raw_get_fmt callback function for call iio_str_to_fixpoint.
v2: cm32181_write_als_id function fixed as it was.
Cc: Kevin Tsai <ktsai@capellamicro.com>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch is fixed [read/write] integration time function.
cm36651 have integration time from 1 to 640 milliseconds.
But, print more then the thousand second. when call *_integration_time attribute.
Because read_integration_time function return IIO_VAL_INT.
read integration time function is changed return IIO_VAL_INT_PLUS_MICRO;
And then .write_raw_get_fmt callback function for parse a fixed-point number from a string.
Some description is revised milliseconds unit.
v2: cm36651_write_int_time function fixed as it was.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Get rid of obsolete uses of goto error_ret and some empty lines.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch fixes some typos in max1363_chip_info_tbl[].
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Remove the hard coded indexes, instead search for usage id and
use the index to set the power and report state.
This will fix issue, where the report descriptor doesn't contain
the full list of possible selector for power and report state.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Linus Torvalds
Paul Gortmaker
Sebastian Reichel
Johannes Thumshirn
Greg Kroah-Hartman
Jonathan Cameron
Lars-Peter Clausen
Johannes Thumshirn
Peter Meerwald
Denis CIOCCA
Archana Patni
Beomho Seo
Hartmut Knaack
Srinivas Pandruvada