If CONFIG_PM_SLEEP is disabled, then iwlwifi doesn't
support suspend/resume handlers and thus mac80211
(correctly) refuses advertising WoWLAN. Disable
WoWLAN in the driver in this case.
Cc: stable@kernel.org
Reported-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enforcing interface combinations broke uses of hwsim
with multiple virtual interfaces. Advertise that all
combinations are possible to fix this.
Reported-by: Nirav Shah <nirav.j2.shah@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since my commit
iwlwifi: use valid TX/RX antenna from hw_params
the config values are pure overrides, not the
real values for all hardware. Therefore, the
EEPROM TX power reading code checks the wrong
values, it should check the hw_params values.
Cc: stable@kernel.org [3.4]
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwifiex uAP supports NL80211_HIDDEN_SSID_ZERO_LEN type of hidden
SSID only. NL80211_HIDDEN_SSID_ZERO_CONTENTS is not supported.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mark bss_config parameters as invalid before setting AP channel.
This prevents from setting invalid parameters while setting AP
channel to FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The definition of I217_PROXY_CTRL must use the BM_PHY_REG() macro instead
of the PHY_REG() macro for PHY page 800 register 70 since it is for a PHY
register greater than the maximum allowed by the latter macro, and fix a
typo setting the I217_MEMPWR register in e1000_suspend_workarounds_ich8lan.
Also for clarity, rename a few defines as bit definitions instead of masks.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
when register_netdev fails, the init'ed NAPIs by netif_napi_add must be
deleted with netif_napi_del, and also when driver unloads, it should
delete the NAPI before unregistering netdevice using unregister_netdev.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we terminate the eeprom access through clearing the CS by:
RTL_W8 (Cfg9346, ~EE_CS); or writeb (~EE_CS, ee_addr);
This would left the eeprom into "Config. Register Write Enable:"
state which is not expcted as the highest two bits were set to
0x11 ( expected is the "Normal" mode (0x00)). Solving this by write
0x0 instead of ~EE_CS when terminating the eeprom access.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we enable the receiver before setting the ring address which could
lead the card DMA into unexpected areas. Solving this by set the ring address
before enabling the receiver.
btw. I find and test this in qemu as I didn't have a 8139cp card in hand. please
review it carefully.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "!mlx4_is_slave" is totally confusing. Fix with
constant MLX4_CMD_NATIVE, which is the intended behavior.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The range check was performed after using the port number.
Reverse this to prevent a potential array overflow.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- pass the following parameters:
- firmware version (added QUERY_FW paravirtualization for that)
- disable Blueflame on slaves. KVM disables write combining on guests,
and we get better performance without BF in this case. (This requires
QUERY_DEV_CAP paravirtualization, also in this commit)
- max qp rdma as destination
- get rid of a chunk of "if (0)" dead code
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port is used as an array index before we know if that is proper.
For example, in the catas event case, port is zero; however,
the port index should lie in the range (1..2).
Fix this by using 'port' only in the events where it is of interest.
Test for port out of range in the default (unhandled event) case,
and do not output a message if it is not an ethernet port.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In SRIOV mode, the number of EQs used when computing the total ICM size
was incorrect.
To fix this, we do the following:
1. We add a new structure to mlx4_dev, mlx4_phys_caps, to contain physical HCA
capabilities. The PPF uses the phys capabilities when it computes things
like ICM size.
The dev_caps structure will then contain the paravirtualized values, making
bookkeeping much easier in SRIOV mode. We add a structure rather than a
single parameter because there will be other fields in the phys_caps.
The first field we add to the mlx4_phys_caps structure is num_phys_eqs.
2. In INIT_HCA, when running in SRIOV mode, the "log_num_eqs" parameter
passed to the FW is the number of EQs per VF/PF; each function (PF or VF)
has this number of EQs available.
However, the total number of EQs which must be allowed for in the ICM is
(1 << log_num_eqs) * (#VFs + #PFs). Rather than compute this quantity,
we allocate ICM space for 1024 EQs (which is the device maximum
number of EQs, and which is the value we place in the mlx4_phys_caps structure).
For INIT_HCA, however, we use the per-function number of EQs as described
above.
Signed-off-by: Marcel Apfelbaum <marcela@dev.mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking changes from David S. Miller:
1) Fix IPSEC header length calculation for transport mode in ESP. The
issue is whether to do the calculation before or after alignment.
Fix from Benjamin Poirier.
2) Fix regression in IPV6 IPSEC fragment length calculations, from Gao
Feng. This is another transport vs tunnel mode issue.
3) Handle AF_UNSPEC connect()s properly in L2TP to avoid OOPSes. Fix
from James Chapman.
4) Fix USB ASIX driver's reception of full sized VLAN packets, from
Eric Dumazet.
5) Allow drop monitor (and, more generically, all generic netlink
protocols) to be automatically loaded as a module. From Neil
Horman.
Fix up trivial conflict in Documentation/feature-removal-schedule.txt
due to new entries added next to each other at the end. As usual.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits)
net/smsc911x: Repair broken failure paths
virtio-net: remove useless disable on freeze
netdevice: Update netif_dbg for CONFIG_DYNAMIC_DEBUG
drop_monitor: Add module alias to enable automatic module loading
genetlink: Build a generic netlink family module alias
net: add MODULE_ALIAS_NET_PF_PROTO_NAME
r6040: Do a Proper deinit at errorpath and also when driver unloads (calling r6040_remove_one)
r6040: disable pci device if the subsequent calls (after pci_enable_device) fails
skb: avoid unnecessary reallocations in __skb_cow
net: sh_eth: fix the rxdesc pointer when rx descriptor empty happens
asix: allow full size 8021Q frames to be received
rds_rdma: don't assume infiniband device is PCI
l2tp: fix oops in L2TP IP sockets for connect() AF_UNSPEC case
mac80211: fix ADDBA declined after suspend with wowlan
wlcore: fix undefined symbols when CONFIG_PM is not defined
mac80211: fix flag check for QoS NOACK frames
ath9k_hw: apply internal regulator settings on AR933x
ath9k_hw: update AR933x initvals to fix issues with high power devices
ath9k: fix a use-after-free-bug when ath_tx_setup_buffer() fails
ath9k: stop rx dma before stopping tx
...
Current failure paths attempt to free resources which we failed to request
and disable resources which we failed to enable ones. This leads to kernel
oops/panic. This patch does some simple re-ordering to prevent this from
happening.
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
disable_cb is just an optimization: it
can not guarantee that there are no callbacks.
In particular it doesn't have any effect when
event index is on.
Instead, detach, napi disable and reset on freeze ensure we don't run
concurrently with a callback.
Remove the useless calls so we get same behaviour
with and without event index.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
so if mdiobus_alloc fails, the errorpath doesnt do a netif_napi_del and also
doesn't set the priv data of the driver to NULL.
at the driver unload stage the driver doesn't remove the NAPI context, and
doesnt' set the priv data to NULL, and also doesn't call the pci_iounmap.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg
Stanislaw Gruszka
Joe Perches
Avinash Patil
Stephan Gatzka
Ondrej Zary
Bruce Allan
Sebastian Andrzej Siewior
Devendra Naga
Jason Wang
Jack Morgenstein
Marcel Apfelbaum
Linus Torvalds
Lee Jones
Michael S. Tsirkin
John W. Linville