The omap watchdog hardware is able to read the watchdog timer counter
register. This implements this functionality in the omap_wdt driver, so
one is can read the time until the watchdog will trigger the reset in
seconds using WDIOC_GETTIMELEFT.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The omap watchdog has the annoying behaviour that writes to most
registers don't have any effect when the watchdog is already running.
Quoting the AM335x reference manual:
To modify the timer counter value (the WDT_WCRR register),
prescaler ratio (the WDT_WCLR[4:2] PTV bit field), delay
configuration value (the WDT_WDLY[31:0] DLY_VALUE bit field), or
the load value (the WDT_WLDR[31:0] TIMER_LOAD bit field), the
watchdog timer must be disabled by using the start/stop sequence
(the WDT_WSPR register).
Currently the timer is stopped in the .probe callback but still there
are possibilities that yield to a situation where omap_wdt_start is
entered with the timer running (e.g. when /dev/watchdog is closed
without stopping and then reopened). In such a case programming the
timeout silently fails!
To circumvent this stop the timer before reprogramming.
Assuming one of the first things the watchdog user does is setting the
timeout explicitly nothing too bad should happen because this explicit
setting works fine.
Fixes: 7768a13c25 ("[PATCH] OMAP: Add Watchdog driver support")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Instead of using an over-long expression involving the ?: operator use
an if and instead of an else branch rely on the fact that the data
structure was allocated using devm_kzalloc. This also allows to put the
used helper variable into a more local scope.
There is no functional change.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This way only a single allocation is needed (per device). Also this
simplifies the data structure used by the driver because there is no
need anymore to link from one struct to the other (by means of
watchdog_{set,get}_drvdata).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Instead of (partly) open coding watchdog_init_timeout to determine the
inital timeout use the core function that exists for exactly this
purpose.
As a side effect the "timeout-sec" device-tree property is recognized now
(though currently unused in the omap device trees).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use devm_ioremap_resource() in order to make the code simpler,
and remove 'struct resource *mem' from 'struct omap_wdt_dev'
and omap_wdt_probe(), resplectively. because the 'mem' variables
are not used anymore. Also the redundant return value check of
platform_get_resource() is removed, because the value is checked
by devm_ioremap_resource().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-watchdog@vger.kernel.org
All OMAP IP blocks expect LE data, but CPU may operate in BE mode.
Need to use endian neutral functions to read/write h/w registers.
I.e instead of __raw_read[lw] and __raw_write[lw] functions code
need to use read[lw]_relaxed and write[lw]_relaxed functions.
If the first simply reads/writes register, the second will byteswap
it if host operates in BE mode.
Changes are trivial sed like replacement of __raw_xxx functions
with xxx_relaxed variant.
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org>
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Like other watchdog drivers, this patch adds new option nowayout
which overwrite WATCHDOG_NOWAYOUT.
Signed-off-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
We forgot to delete this in the commit 4f4753d9 (watchdog: omap_wdt:
convert to devm_ functions), and as a result the following compilation
warning was introduced:
drivers/watchdog/omap_wdt.c: In function 'omap_wdt_remove':
drivers/watchdog/omap_wdt.c:299:19: warning: unused variable 'res' [-Wunused-variable]
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use devm_kzalloc(), devm_request_mem_region() ande devm_ioremap()
to simplify the code.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Convert omap_wdt to new watchdog core. On OMAP boards, there are usually
multiple watchdogs. Since the new watchdog core supports multiple
watchdogs, all watchdog drivers used on OMAP should be converted.
The legacy watchdog device node is still created, so this should not
break existing users.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Tested-by: Jarkko Nikula <jarkko.nikula@jollamobile.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Pull ARM SoC power management and clock changes from Olof Johansson:
"This branch contains a largeish set of updates of power management and
clock setup. The bulk of it is for OMAP/AM33xx platforms, but also a
few around hotplug/suspend/resume on Exynos.
It includes a split-up of some of the OMAP clock data into separate
files which adds to the diffstat, but gross delta is fairly reasonable."
* tag 'pm-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (60 commits)
ARM: OMAP: Move plat-omap/dma-omap.h to include/linux/omap-dma.h
ASoC: OMAP: mcbsp fixes for enabling ARM multiplatform support
watchdog: OMAP: fixup for ARM multiplatform support
ARM: EXYNOS: Add flush_cache_all in suspend finisher
ARM: EXYNOS: Remove scu_enable from cpuidle
ARM: EXYNOS: Fix soft reboot hang after suspend/resume
ARM: EXYNOS: Add support for rtc wakeup
ARM: EXYNOS: fix the hotplug for Cortex-A15
ARM: OMAP2+: omap_device: Correct resource handling for DT boot
ARM: OMAP2+: hwmod: Add possibility to count hwmod resources based on type
ARM: OMAP2+: hwmod: Add support for per hwmod/module context lost count
ARM: OMAP2+: PRM: initialize some PRM functions early
ARM: OMAP2+: voltage: fixup oscillator handling when CONFIG_PM=n
ARM: OMAP4: USB: power down MUSB PHY during boot
ARM: OMAP2+: clock: Cleanup !CONFIG_COMMON_CLK parts
ARM: OMAP2xxx: clock: drop obsolete clock data
ARM: OMAP2: clock: Cleanup !CONFIG_COMMON_CLK parts
ARM: OMAP3+: DPLL: drop !CONFIG_COMMON_CLK sections
ARM: AM33xx: clock: drop obsolete clock data
ARM: OMAP3xxx: clk: drop obsolete clock data
...
Pull ARM SoC cleanups on various subarchitectures from Olof Johansson:
"Cleanup patches for various ARM platforms and some of their associated
drivers. There's also a branch in here that enables Freescale i.MX to
be part of the multiplatform support -- the first "big" SoC that is
moved over (more multiplatform work comes in a separate branch later
during the merge window)."
Conflicts fixed as per Olof, including a silent semantic one in
arch/arm/mach-omap2/board-generic.c (omap_prcm_restart() was renamed to
omap3xxx_restart(), and a new user of the old name was added).
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (189 commits)
ARM: omap: fix typo on timer cleanup
ARM: EXYNOS: Remove unused regs-mem.h file
ARM: EXYNOS: Remove unused non-dt support for dwmci controller
ARM: Kirkwood: Use hw_pci.ops instead of hw_pci.scan
ARM: OMAP3: cm-t3517: use GPTIMER for system clock
ARM: OMAP2+: timer: remove CONFIG_OMAP_32K_TIMER
ARM: SAMSUNG: use devm_ functions for ADC driver
ARM: EXYNOS: no duplicate mask/unmask in eint0_15
ARM: S3C24XX: SPI clock channel setup is fixed for S3C2443
ARM: EXYNOS: Remove i2c0 resource information and setting of device names
ARM: Kirkwood: checkpatch cleanups
ARM: Kirkwood: Fix sparse warnings.
ARM: Kirkwood: Remove unused includes
ARM: kirkwood: cleanup lsxl board includes
ARM: integrator: use BUG_ON where possible
ARM: integrator: push down SC dependencies
ARM: integrator: delete static UART1 mapping
ARM: integrator: delete SC mapping on the CP
ARM: integrator: remove static CP syscon mapping
ARM: integrator: remove static AP syscon mapping
...
Recent changes to the omap_wdt.c removed the dependencies to
the core omap code, but forgot to remove mach/hardware.h.
We cannot include any plat headers with multiplatform
support enabled.
cc: Wim Van Sebroeck <wim@iguana.be>
cc: linux-watchdog@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Previously the OMAP watchdog driver used a non-standard way to report
the chip reset source via the GETBOOTSTATUS ioctl. This patch
converts the driver to use the standard WDIOF_* flags for this
purpose.
This patch may break existing userspace code that uses the existing
non-standard data format returned by the OMAP watchdog driver's
GETBOOTSTATUS ioctl. To fetch detailed reset source information,
userspace code will need to retrieve it directly from the CGRM or PRM
drivers when those are completed.
Previously, to fetch the reset source, the driver either read a
register outside the watchdog IP block (OMAP1), or called a function
exported directly from arch/arm/mach-omap2. Both approaches are
broken. This patch also converts the driver to use a platform_data
function pointer. This approach is temporary, and is due to the lack
of drivers for the OMAP16xx+ Clock Generation and Reset Management IP
block and the OMAP2+ Power and Reset Management IP block. Once
drivers are available for those IP blocks, the watchdog driver can be
converted to call exported functions from those drivers directly.
At that point, the platform_data function pointer can be removed.
In the short term, this patch is needed to allow the PRM code to be
removed from arch/arm/mach-omap2 (it is being moved to a driver).
This version integrates a fix from Jon Hunter <jon-hunter@ti.com>
that avoids a NULL pointer dereference in a DT-only boot, and integrates
a patch commit message fix from Felipe Balbi <balbi@ti.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
[paul@pwsan.com: integrated pdata fix from Jon Hunter]
Cc: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: integrated changelog fix from Felipe Balbi]
Cc: Felipe Balbi <balbi@ti.com>
As the plat and mach includes need to disappear for single zImage work,
we need to remove plat/hardware.h.
Do this by splitting plat/hardware.h into omap1 and omap2+ specific files.
The old plat/hardware.h already has omap1 only defines, so it gets moved
to mach/hardware.h for omap1. For omap2+, we use the local soc.h
that for now just includes the related SoC headers to keep this patch more
readable.
Note that the local soc.h still includes plat/cpu.h that can be dealt
with in later patches. Let's also include plat/serial.h from common.h for
all the board-*.c files. This allows making the include files local later
on without patching these files again.
Note that only minimal changes are done in this patch for the
drivers/watchdog/omap_wdt.c driver to keep things compiling. Further
patches are needed to eventually remove cpu_is_omap usage in the drivers.
Also only minimal changes are done to sound/soc/omap/* to remove the
unneeded includes and to define OMAP44XX_MCPDM_L3_BASE locally so there's
no need to include omap44xx.h.
While at it, also sort some of the includes in the standard way.
Cc: linux-watchdog@vger.kernel.org
Cc: alsa-devel@alsa-project.org
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Cc: Liam Girdwood <lrg@ti.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Lars Poeschel
Uwe Kleine-König
Tony Lindgren
Wolfram Sang
Jingoo Han
Paul Gortmaker
Victor Kamensky
Pali Rohár
Aaro Koskinen
Linus Torvalds
Bill Pemberton
Paul Walmsley