Add MIPS dependency for dm9000 ethernet controller. Indeed this controller
is used by some embedded platforms based on MIPS CPUs.
Signed-off-by: Franck Bui-Huu <franck.bui@gmail.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
A BIOS bug affecting some multiport tulip NICs requires an irq fixup
in tulip_core.c. This has only been enabled for i686, but it is
needed for x86_64 as well.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Disable TX status deferral (EMACx_MR[MWSW=001]) in half-duplex mode.
I have two reports when EMAC stops transmitting when connected to a
hub. TX ring debug printouts show complete mess when this happens,
probably hardware collision handling doesn't work quite well in this
mode.
This is relevant only for SoCs with EMAC4 core (440GX, 440SP, 440SPe).
Tested on 440GX.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Don't enable the pci device twice (already done in the probe
routine). Propogate the error codes from pci_request_region
back to initial probing.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The sk98lin driver doesn't do proper error number handling
during initialization. Note: -EAGAIN is a bogus return value for
hardware errors.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Sk98lin driver error recovery on two port boards is bad.
If it fails the second allocation, it will not release resources
properly. Also it registers the second port in the pci driver data
If second port fails, might as well go with one port.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Sk98lin 64bit memory handling is wrong. It doesn't set the
highdma flag; i.e. the kernel always does bounce buffers.
It doesn't fallback to 32 bit mask if it can't get 64 bit mask.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Sk98lin driver has a routine marked __init that is called from
the probe code. If using pci hotplug, this could be called after
the initialization so it needs to be marked __devinit.
So if you hot added a sk98lin board, the kernel would crash.
I don't have hot plug hardware to actually try this feat.
Also, there are two routines, only called from SkGeBoardInit that can
be marked __devinit.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Since version 4.1 the gcc is warning about ignored attributes. This patch is
using the equivalent attribute on the struct instead of on each of the
structure or union members.
GCC Manual:
"Specifying Attributes of Types
packed
This attribute, attached to struct or union type definition, specifies
that
each member of the structure or union is placed to minimize the memory
required. When attached to an enum definition, it indicates that the
smallest integral type should be used.
Specifying this attribute for struct and union types is equivalent to
specifying the packed attribute on each of the structure or union
members."
Signed-off-by: Jan Blunck <jblunck@suse.de>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some ARM platforms have the ability to program the interrupt controller to
detect various interrupt edges and/or levels. For some platforms, this is
critical to setup correctly, particularly those which the setting is dependent
on the device.
Currently, ARM drivers do (eg) the following:
err = request_irq(irq, ...);
set_irq_type(irq, IRQT_RISING);
However, if the interrupt has previously been programmed to be level sensitive
(for whatever reason) then this will cause an interrupt storm.
Hence, if we combine set_irq_type() with request_irq(), we can then safely set
the type prior to unmasking the interrupt. The unfortunate problem is that in
order to support this, these flags need to be visible outside of the ARM
architecture - drivers such as smc91x need these flags and they're
cross-architecture.
Finally, the SA_TRIGGER_* flag passed to request_irq() should reflect the
property that the device would like. The IRQ controller code should do its
best to select the most appropriate supported mode.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
PNX010X support for CS89x0 should be conditional on NET_PCI, as it is an 'on
board controller' and NET_PCI includes that category of NICs. Since
ARCH_PNX0105 was recently changed to ARCH_PNX010X, incorporate that change as
well while we're at it.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: dmitry pervushin <dpervushin@ru.mvista.com>
Cc: <dsaxena@plexity.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
readword() and writeword() take a 'struct net_device *' and deref its
->base_addr member. Make them take the base_addr directly instead, so
that we can switch the other occurences of inw/outw in the file over
to readword/writeword as well.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: dmitry pervushin <dpervushin@ru.mvista.com>
Cc: <dsaxena@plexity.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Olaf Hering
Kenji Kaneshige
Adrian Bunk
Franck
Christoph Dworzak
Eugene Surovegin
Stephen Hemminger
Jan Blunck
Russell King
Lennert Buytenhek
Francois Romieu