regmap_bulk_read() should decay to performing individual reads if
we're using a "no-bus" regmap. Unfortunately, it returns an
error because there is no map->bus pointer. Fix it.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
clk_get() returns an error pointer, or a valid token to pass back to the
clock API. Hence, the result must be checked with IS_ERR(), not by
comparison against NULL.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch give a warning when calling regmap_register_patch with
parameter num_regs <= 0.
When the num_regs parameter is zero and krealloc doesn't fail,
then the code would return an uninitialized value. However,
calling this function with num_regs == 0, would be a waste as it
essentially does nothing.
Signed-off-by: Cai Zhiyong <caizhiyong@huawei.com>
Reviewed-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
fix a trivial copy'n'paste error in the regmap kerneldoc, s/write/read/
for the regmap_read(), regmap_raw_read() and regmap_bulk_read() routines
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add basic support for the System Power Management Interface (SPMI) bus.
This is a simple implementation which only implements register accesses
via the Extended Register Read/Write Long commands.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
If called early enough, regmap_debugfs_init causes a crash, if the
fs subsystem does not have its mount cache created yet. Even if this
would work, the root node for the regmap debugfs is still missing,
thus postpone the regmap_debugfs_init in this case until the root
node is created. A special regmap_debugfs_early list is created for
this purpose which is parsed later in the boot.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
clear the status bit if the mask register doesn't prevent
the chip level irq from being asserted
OR in the following sequence, there will be irq storm happens:
1) interrupt is triggered;
2) another thread disables it(the mask bit is set);
3) _Then_ the interrupt thread is not ACKed(the status bit is not cleared),
and it's ignored;
4) if the irq is still asserted because of the uncleared status bit,
the irq storm happens;
Signed-off-by: Yi Zhang <yizhang@marvell.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Extend the interface for async I/O by allowing the value buffer to be
omitted and sending the value as part of the register buffer, minimising
the number of separate hardware operations required.
Signed-off-by: Mark Brown <broonie@linaro.org>
If the value is zero then assume it has been included in the register data
and don't send anything, minimising the number of interactions with the
hardware.
Signed-off-by: Mark Brown <broonie@linaro.org>
New API regmap_multi_reg_write() is defined that allows a set of reg,val
pairs to be written to a I2C client device as one block transfer from the
point of view of a single I2C master system.
A simple demonstration implementation is included that just splits the
block write request into a sequence of single register writes.
The implementation will be modified later to support those I2C clients
that implement the alternative non-standard MULTIWRITE block write mode
so to achieve a single I2C transfer that will be atomic even in multiple
I2C master systems.
Signed-off-by: Anthony Olech <anthony.olech.opensource@diasemi.com>
Signed-off-by: David Dajun Chen <david.chen@diasemi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Try to speed up I/O a little by not synchronising until we are finished
scheduling writes. A brief survey of existing users suggests we have none
that would currently benefit from an async cache sync.
Signed-off-by: Mark Brown <broonie@linaro.org>
When regmap_bulk_write() is called with the map->use_single_rw flag set
an immediate mutex deadlock happens because regmap_raw_write() is called
after obtaining the mutex and regmap_raw_write() itself then tries to
obtain the mutex as well.
It is obvious that no one other than myself tried it with a real device.
I did, but only for the purposes of an experiment and demonstration.
But even if this situation will never ever happen with a real device, it
is a bug and therefore should be fixed.
Signed-off-by: Anthony Olech <anthony.olech.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make it easier for drivers to include single register writes in
asynchronous sequences by providing async versions of the write
and update bits operations. The update bits operations are only
likely to be effective when used with devices that have caches
but this is common enough to be useful.
Signed-off-by: Mark Brown <broonie@linaro.org>
Rather than passing a flag around through the entire call stack store it
in the regmap struct and read it when required. This minimises the
visibility of the feature through the API, minimising the code updates
needed to use it more widely.
Signed-off-by: Mark Brown <broonie@linaro.org>
Since it is quite common for single register raw or async writes to be
generated by rbtree cache syncs or firmware downloads and essentially all
hardware will be faster with only a single transfer optimise this case by
copying single values into the internal scratch buffer before sending.
Signed-off-by: Mark Brown <broonie@linaro.org>
Mark Brown
Stephen Boyd
Stephen Warren
Cai Zhiyong
Courtney Cavin
Gerhard Sittig
Josh Cartwright
Tero Kristo
Yi Zhang
Anthony Olech