DS1302 is an half-duplex SPI device. The driver respects this fact now.
Pin configurations should be implemented using SPI subsystem.
Signed-off-by: Sergei Ianovich <ynvich@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This adds support to
- enable/disable the thermometer
- set the temperature scanning interval
- read the current temperature that is used for temp compensation.
via hwmon interface
Signed-off-by: Michael Buesch <m@bues.ch>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
There are several arch-specific RTC drivers that can be successfully
compiled on other platforms. Add a COMPILE_TEST dependency for those.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Maxim Semiconductor's PMIC MAX77686 has RTC IP which is
reused in the MAX77620/MAX20024 PMICs.
Add support for these devices in MAX77686 RTC driver. This
device does not have RTC alarm pending status outside of
RTC IP. The RTC IP is having separate I2C address for its
register access.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The Kconfig option for rv3029 is not mentioning any part number, explicitly
show rv3029.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The RTC entries are mostly grouped by vendor. Move the few outliers in
place.
Also, change the one occurrence of 'nxp' to 'NXP' to make all NXP
entries consistent.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This driver adds support for the PIC32 real time clock and calendar
peripheral:
- reading and setting time
- alarms provided by dedicated IRQ
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
At the moment the "sun6i" RTC drivers depends on having two specific
SoC families selected.
The Allwinner A64 SoC has the same RTC, so extend the Kconfig option
to allow inclusion of the driver for all Allwinner SoCs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The RX6110 comes in two different variants: SPI and I2C.
This driver only supports the SPI variant.
If the need ever arises to also support the I2C variant, this driver
could easily be refactored to support both cases.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
DS3231 has the temperature registers with a resolution of 0.25
degree celsius. This enables to get the value through hwmon.
# cat /sys/class/i2c-adapter/i2c-2/2-0068/hwmon/hwmon0/temp1_input
21000
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The mt6397 RTC driver can be built either when the MFD_MT6397 driver
is enabled (which selects IRQ_DOMAIN), or when compile testing.
The latter however fails without IRQ domains:
drivers/rtc/rtc-mt6397.c: In function 'mtk_rtc_probe':
drivers/rtc/rtc-mt6397.c:326:13: error: implicit declaration of function 'irq_create_mapping' [-Werror=implicit-function-declaration]
rtc->irq = irq_create_mapping(mt6397_chip->irq_domain, res->start);
This adds an explicit dependency for the COMPILE_TEST case.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This driver supports the following functions:
- reading and settings time
- alarms when connected to an IRQ
- reading and clearing the voltage low flags
- nvram
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add DA9062 RTC support into the existing DA9063 RTC driver component by
using generic access tables for common register and bit mask definitions.
The following change will add generic register and bit mask support to the
DA9063 RTC. The changes are slightly complicated by requiring support for
three register sets: DA9063-AD, DA9063-BB and DA9062-AA.
The following alterations have been made to the DA9063 RTC:
- Addition of a da9063_compatible_rtc_regmap structure to hold all generic
registers and bitmasks for this type of RTC component.
- A re-write of struct da9063 to use pointers for regmap and compatible
registers/masks definitions
- Addition of a of_device_id table for DA9063 and DA9062 defaults
- Refactoring functions to use struct da9063_compatible_rtc accesses to
generic registers/masks instead of using defines from registers.h
- Re-work of da9063_rtc_probe() to use of_match_node() and dev_get_regmap()
to provide initialisation of generic registers and masks and access to
regmap
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Mylène Josserand
Sergey Yanovich
Alexandre Belloni
Akinobu Mita
Michael Büsch
Laxman Dewangan
Soren Brinkmann
Joshua Henderson
Oleksij Rempel
Andre Przywara
Steffen Trumtrar
Arnd Bergmann
Javier Martinez Canillas
Akshay Bhat
Ivan Grimaldi
Suneel Garapati
Rob Herring
S Twiss