Add leds-gpio platform device for controlling LEDs connected to IOC on
RBTX49XX and JMR3927 board.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The IOC interrupt status register on RBTX49XX only have 8 bits. Use
8-bit version of __fls() to optimize interrupt handlers.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
TXx9 SoCs have pin multiplex. Stop some controller modules which can
not be used due to pin configurations.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Routerboard 532 bootloader passes the korina ethernet
MAC adapter address to the kernel on the command line.
Document this in the kernel-parameters file.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch converts the rb532 code to use gpio library
and register its gpio chip.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch removes these two unused functions :
rc32434_sync_delay and rc32434_sync_udelay
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch cleans up headers and regroups informations to
where they should reside. While moving, try to have a
consistant naming for defines.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We are no longer using setup_serial_port. So just remove it
from the prom code.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When there is only platform device of the same type, id = -1
should be used, fix this.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch replaces a raw read using volatiles
with a readl.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We are no longer using gpio bootup state, so do not export
it and do not parse the kernel command line tag for it.
Instead we provide gpio-keys for the button the gpio bootup
state was checking.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes the misuse of virtual addresses for the GPIO and third
device controller which would lead to problems while accessing ioremap'd
registers.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch moves GPIO related definitions to gpio.h and IRQ
related to irq.h
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Helper routines in txx9/rbtx4938/spi_eeprom.c is not TX4938 specific.
Move it to txx9/generic/ directory and make it works with SPI bus
number other than 0.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
create mode 100644 arch/mips/txx9/generic/spi_eeprom.c
delete mode 100644 arch/mips/txx9/rbtx4938/spi_eeprom.c
Add TOSHIBA_RBTX4938_MPLEX_KEEP to keep MPLEX settings by firmware.
Also replace some printk with pr_info.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
TX39/TX49 can enable/disable I/D cache at runtime. Add kernel options
to control them. This is useful to debug some cache-related issues,
such as aliasing or I/D coherency. Also enable CWF bit for TX49 SoCs.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Atsushi Nemoto
Florian Fainelli