PCI controllers and pci-pci bridges may have not been fully initialized
regarding cache line and defaul latency.
This partly reverts
commit 5f0e9b4 ("parisc: Remove unused pcibios_init_bus()")
Signed-off-by: Helge Deller <deller@gmx.de>
When using the Promise TX2+ SATA controller on PA-RISC, the system often
crashes with kernel panic, for example just writing data with the dd
utility will make it crash.
Kernel panic - not syncing: drivers/parisc/sba_iommu.c: I/O MMU @ 000000000000a000 is out of mapping resources
CPU: 0 PID: 18442 Comm: mkspadfs Not tainted 4.4.0-rc2 #2
Backtrace:
[<000000004021497c>] show_stack+0x14/0x20
[<0000000040410bf0>] dump_stack+0x88/0x100
[<000000004023978c>] panic+0x124/0x360
[<0000000040452c18>] sba_alloc_range+0x698/0x6a0
[<0000000040453150>] sba_map_sg+0x260/0x5b8
[<000000000c18dbb4>] ata_qc_issue+0x264/0x4a8 [libata]
[<000000000c19535c>] ata_scsi_translate+0xe4/0x220 [libata]
[<000000000c19a93c>] ata_scsi_queuecmd+0xbc/0x320 [libata]
[<0000000040499bbc>] scsi_dispatch_cmd+0xfc/0x130
[<000000004049da34>] scsi_request_fn+0x6e4/0x970
[<00000000403e95a8>] __blk_run_queue+0x40/0x60
[<00000000403e9d8c>] blk_run_queue+0x3c/0x68
[<000000004049a534>] scsi_run_queue+0x2a4/0x360
[<000000004049be68>] scsi_end_request+0x1a8/0x238
[<000000004049de84>] scsi_io_completion+0xfc/0x688
[<0000000040493c74>] scsi_finish_command+0x17c/0x1d0
The cause of the crash is not exhaustion of the IOMMU space, there is
plenty of free pages. The function sba_alloc_range is called with size
0x11000, thus the pages_needed variable is 0x11. The function
sba_search_bitmap is called with bits_wanted 0x11 and boundary size is
0x10 (because dma_get_seg_boundary(dev) returns 0xffff).
The function sba_search_bitmap attempts to allocate 17 pages that must not
cross 16-page boundary - it can't satisfy this requirement
(iommu_is_span_boundary always returns true) and fails even if there are
many free entries in the IOMMU space.
How did it happen that we try to allocate 17 pages that don't cross
16-page boundary? The cause is in the function iommu_coalesce_chunks. This
function tries to coalesce adjacent entries in the scatterlist. The
function does several checks if it may coalesce one entry with the next,
one of those checks is this:
if (startsg->length + dma_len > max_seg_size)
break;
When it finishes coalescing adjacent entries, it allocates the mapping:
sg_dma_len(contig_sg) = dma_len;
dma_len = ALIGN(dma_len + dma_offset, IOVP_SIZE);
sg_dma_address(contig_sg) =
PIDE_FLAG
| (iommu_alloc_range(ioc, dev, dma_len) << IOVP_SHIFT)
| dma_offset;
It is possible that (startsg->length + dma_len > max_seg_size) is false
(we are just near the 0x10000 max_seg_size boundary), so the funcion
decides to coalesce this entry with the next entry. When the coalescing
succeeds, the function performs
dma_len = ALIGN(dma_len + dma_offset, IOVP_SIZE);
And now, because of non-zero dma_offset, dma_len is greater than 0x10000.
iommu_alloc_range (a pointer to sba_alloc_range) is called and it attempts
to allocate 17 pages for a device that must not cross 16-page boundary.
To fix the bug, we must make sure that dma_len after addition of
dma_offset and alignment doesn't cross the segment boundary. I.e. change
if (startsg->length + dma_len > max_seg_size)
break;
to
if (ALIGN(dma_len + dma_offset + startsg->length, IOVP_SIZE) > max_seg_size)
break;
This patch makes this change (it precalculates max_seg_boundary at the
beginning of the function iommu_coalesce_chunks). I also added a check
that the mapping length doesn't exceed dma_get_seg_boundary(dev) (it is
not needed for Promise TX2+ SATA, but it may be needed for other devices
that have dma_get_seg_boundary lower than dma_get_max_seg_size).
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>
Revert dff22d2054 ("PCI: Call pci_read_bridge_bases() from core instead
of arch code").
Reading PCI bridge windows is not arch-specific in itself, but there is PCI
core code that doesn't work correctly if we read them too early. For
example, Hannes found this case on an ARM Freescale i.mx6 board:
pci_bus 0000:00: root bus resource [mem 0x01000000-0x01efffff]
pci 0000:00:00.0: PCI bridge to [bus 01-ff]
pci 0000:00:00.0: BAR 8: no space for [mem size 0x01000000] (mem window)
pci 0000:01:00.0: BAR 2: failed to assign [mem size 0x00200000]
pci 0000:01:00.0: BAR 1: failed to assign [mem size 0x00004000]
pci 0000:01:00.0: BAR 0: failed to assign [mem size 0x00000100]
The 00:00.0 mem window needs to be at least 3MB: the 01:00.0 device needs
0x204100 of space, and mem windows are megabyte-aligned.
Bus sizing can increase a bridge window size, but never *decrease* it (see
d65245c329 ("PCI: don't shrink bridge resources")). Prior to
dff22d2054, ARM didn't read bridge windows at all, so the "original size"
was zero, and we assigned a 3MB window.
After dff22d2054, we read the bridge windows before sizing the bus. The
firmware programmed a 16MB window (size 0x01000000) in 00:00.0, and since
we never decrease the size, we kept 16MB even though we only needed 3MB.
But 16MB doesn't fit in the host bridge aperture, so we failed to assign
space for the window and the downstream devices.
I think this is a defect in the PCI core: we shouldn't rely on the firmware
to assign sensible windows.
Ray reported a similar problem, also on ARM, with Broadcom iProc.
Issues like this are too hard to fix right now, so revert dff22d2054.
Reported-by: Hannes <oe5hpm@gmail.com>
Reported-by: Ray Jui <rjui@broadcom.com>
Link: http://lkml.kernel.org/r/CAAa04yFQEUJm7Jj1qMT57-LG7ZGtnhNDBe=PpSRa70Mj+XhW-A@mail.gmail.com
Link: http://lkml.kernel.org/r/55F75BB8.4070405@broadcom.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Commit 3a9ad0b ("PCI: Add pci_bus_addr_t") unconditionally introduced usage of
64-bit PCI bus addresses on all 64-bit platforms which broke PA-RISC.
It turned out that due to enabling the 64-bit addresses, the PCI logic decided
to use the GMMIO instead of the LMMIO region. This commit simply disables
registering the GMMIO and thus we fall back to use the LMMIO region as before.
Reverts commit 45ea2a5fed
("PCI: Don't use 64-bit bus addresses on PA-RISC")
To: linux-parisc@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Meelis Roos <mroos@linux.ee>
Cc: stable@vger.kernel.org # v3.19+
Signed-off-by: Helge Deller <deller@gmx.de>
Pull irq updates from Thomas Gleixner:
"This updated pull request does not contain the last few GIC related
patches which were reported to cause a regression. There is a fix
available, but I let it breed for a couple of days first.
The irq departement provides:
- new infrastructure to support non PCI based MSI interrupts
- a couple of new irq chip drivers
- the usual pile of fixlets and updates to irq chip drivers
- preparatory changes for removal of the irq argument from interrupt
flow handlers
- preparatory changes to remove IRQF_VALID"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (129 commits)
irqchip/imx-gpcv2: IMX GPCv2 driver for wakeup sources
irqchip: Add bcm2836 interrupt controller for Raspberry Pi 2
irqchip: Add documentation for the bcm2836 interrupt controller
irqchip/bcm2835: Add support for being used as a second level controller
irqchip/bcm2835: Refactor handle_IRQ() calls out of MAKE_HWIRQ
PCI: xilinx: Fix typo in function name
irqchip/gic: Ensure gic_cpu_if_up/down() programs correct GIC instance
irqchip/gic: Only allow the primary GIC to set the CPU map
PCI/MSI: pci-xgene-msi: Consolidate chained IRQ handler install/remove
unicore32/irq: Prepare puv3_gpio_handler for irq argument removal
tile/pci_gx: Prepare trio_handle_level_irq for irq argument removal
m68k/irq: Prepare irq handlers for irq argument removal
C6X/megamode-pic: Prepare megamod_irq_cascade for irq argument removal
blackfin: Prepare irq handlers for irq argument removal
arc/irq: Prepare idu_cascade_isr for irq argument removal
sparc/irq: Use access helper irq_data_get_affinity_mask()
sparc/irq: Use helper irq_data_get_irq_handler_data()
parisc/irq: Use access helper irq_data_get_affinity_mask()
mn10300/irq: Use access helper irq_data_get_affinity_mask()
irqchip/i8259: Prepare i8259_irq_dispatch for irq argument removal
...
Use %ps for actual addresses, otherwise you'll get bad output
on arches like parisc64 where %pf expects a function descriptor.
This wasn't normally seen on parisc64 because the code is not built
unless DEBUG_SUPERIO_INIT is manually defined.
Patch modified by Helge Deller to utilize KERN_DEBUG.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: linux-parisc@vger.kernel.org
cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Helge Deller <deller@gmx.de>
The only reason to keep parisc's private asm/scatterlist.h was that it
had the macro sg_virt_addr(). Convert all callers to use something else
(sometimes just sg->offset was enough, others should use sg_virt()), and
we can just use the asm-generic scatterlist.h instead.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Dave Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Pull trivial tree from Jiri Kosina:
"Usual trivial tree updates. Nothing outstanding -- mostly printk()
and comment fixes and unused identifier removals"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
goldfish: goldfish_tty_probe() is not using 'i' any more
powerpc: Fix comment in smu.h
qla2xxx: Fix printks in ql_log message
lib: correct link to the original source for div64_u64
si2168, tda10071, m88ds3103: Fix firmware wording
usb: storage: Fix printk in isd200_log_config()
qla2xxx: Fix printk in qla25xx_setup_mode
init/main: fix reset_device comment
ipwireless: missing assignment
goldfish: remove unreachable line of code
coredump: Fix do_coredump() comment
stacktrace.h: remove duplicate declaration task_struct
smpboot.h: Remove unused function prototype
treewide: Fix typo in printk messages
treewide: Fix typo in printk messages
mod_devicetable: fix comment for match_flags
Every PCI-PCI bridge window should fit inside an upstream bridge window
because orphaned address space is unreachable from the primary side of the
upstream bridge. If we inherit invalid bridge windows that overlap an
upstream window from firmware, clip them to fit and update the bridge
accordingly.
[bhelgaas: changelog]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=85491
Reported-by: Marek Kordik <kordikmarek@gmail.com>
Fixes: 5b28541552 ("PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: "James E.J. Bottomley" <jejb@parisc-linux.org>
CC: Helge Deller <deller@gmx.de>
CC: linux-parisc@vger.kernel.org
Pull scheduler updates from Ingo Molnar:
"The main changes in this cycle were:
- Optimized support for Intel "Cluster-on-Die" (CoD) topologies (Dave
Hansen)
- Various sched/idle refinements for better idle handling (Nicolas
Pitre, Daniel Lezcano, Chuansheng Liu, Vincent Guittot)
- sched/numa updates and optimizations (Rik van Riel)
- sysbench speedup (Vincent Guittot)
- capacity calculation cleanups/refactoring (Vincent Guittot)
- Various cleanups to thread group iteration (Oleg Nesterov)
- Double-rq-lock removal optimization and various refactorings
(Kirill Tkhai)
- various sched/deadline fixes
... and lots of other changes"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (72 commits)
sched/dl: Use dl_bw_of() under rcu_read_lock_sched()
sched/fair: Delete resched_cpu() from idle_balance()
sched, time: Fix build error with 64 bit cputime_t on 32 bit systems
sched: Improve sysbench performance by fixing spurious active migration
sched/x86: Fix up typo in topology detection
x86, sched: Add new topology for multi-NUMA-node CPUs
sched/rt: Use resched_curr() in task_tick_rt()
sched: Use rq->rd in sched_setaffinity() under RCU read lock
sched: cleanup: Rename 'out_unlock' to 'out_free_new_mask'
sched: Use dl_bw_of() under RCU read lock
sched/fair: Remove duplicate code from can_migrate_task()
sched, mips, ia64: Remove __ARCH_WANT_UNLOCKED_CTXSW
sched: print_rq(): Don't use tasklist_lock
sched: normalize_rt_tasks(): Don't use _irqsave for tasklist_lock, use task_rq_lock()
sched: Fix the task-group check in tg_has_rt_tasks()
sched/fair: Leverage the idle state info when choosing the "idlest" cpu
sched: Let the scheduler see CPU idle states
sched/deadline: Fix inter- exclusive cpusets migrations
sched/deadline: Clear dl_entity params when setscheduling to different class
sched/numa: Kill the wrong/dead TASK_DEAD check in task_numa_fault()
...
Fix the serial console on machines where the serial port is located on
the SuperIO chip.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: Peter Hurley <peter@hurleysoftware.com>
Using memset before strncpy just to ensure a trailing null character is
an unnecessary double writing of a string
Patch modified by Helge Deller to additionally reduce stack usage.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Helge Deller <deller@gmx.de>
We can't use dev->mod_index for selecting the interrupt routing entry,
because it's not an index into interrupt routing table. It will be even
wrong on a machine with 2 CPUs (4 cores). But all needed information is
contained in the PAT entries for the serial ports. mod[0] contains the
iosapic address and mod_info has some indications for the interrupt
input (at least it looks like it). This patch implements the searching
for the right iosapic and uses this interrupt input information.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: <stable@vger.kernel.org> # 3.10
Signed-off-by: Helge Deller <deller@gmx.de>
Christoph Hellwig
Helge Deller
Mikulas Patocka
Bjorn Helgaas
Andy Shevchenko
Linus Torvalds
Jiang Liu
Lorenzo Pieralisi
Scott Wood
Matthew Wilcox
Joe Perches
Masanari Iida
Yinghai Lu
Rickard Strandqvist
Kirill Tkhai
Hans Wennborg
Thomas Bogendoerfer