Pull LED updates from Jacek Anaszewski:
"This time we're removing more than adding:
Removed drivers:
leds-versatile:
- all users of the Versatile LED driver are deleted and replaced
with the very generic leds-syscon
leds-sead3:
- SEAD3 is using the generic leds-syscon & regmap based
register-bit-led driver
LED class drivers improvements:
ledtrig-gpio:
- use threaded IRQ, which both simplifies the code because we can
drop the workqueue indirection, and it enables using the trigger
for GPIOs that work with threaded IRQs themselves
- refresh LED state after GPIO change since the new GPIO may have
a different state than the old one
leds-lp55xx:
- make various arrays static const
leds-pca963x:
- add bindings to invert polarity"
* tag 'leds_for_4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: lp55xx: make various arrays static const
leds: Remove SEAD-3 driver
leds: trigger: gpio: Use threaded IRQ
leds: trigger: gpio: Refresh LED state after GPIO change
leds: Delete obsolete Versatile driver
leds: pca963x: Add bindings to invert polarity
Linux 4.12-rc6
* tag 'v4.12-rc6': (813 commits)
Linux 4.12-rc6
mm: larger stack guard gap, between vmas
virtio_balloon: disable VIOMMU support
mm: correct the comment when reclaimed pages exceed the scanned pages
userfaultfd: shmem: handle coredumping in handle_userfault()
mm: numa: avoid waiting on freed migrated pages
swap: cond_resched in swap_cgroup_prepare()
mm/memory-failure.c: use compound_head() flags for huge pages
perf unwind: Report module before querying isactivation in dwfl unwind
fs: pass on flags in compat_writev
objtool: Add fortify_panic as __noreturn function
powerpc/debug: Add missing warn flag to WARN_ON's non-builtin path
USB: gadgetfs, dummy-hcd, net2280: fix locking for callbacks
drm: mxsfb_crtc: Reset the eLCDIF controller
drm/mgag200: Fix to always set HiPri for G200e4 V2
i2c: ismt: fix wrong device address when unmap the data buffer
i2c: rcar: use correct length when unmapping DMA
powerpc/xive: Fix offset for store EOI MMIOs
drm/tegra: Correct idr_alloc() minimum id
drm/tegra: Fix lockup on a use of staging API
...
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Pull LED fixes from Jacek Anaszewski:
"Two LED fixes:
- fix signal source assignment for leds-bcm6328
- revert patch that intended to fix LED behavior on suspend but it
had a side effect preventing suspend at all due to uevent being
sent on trigger removal"
* tag 'led_fixes_for_4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
Revert "leds: handle suspend/resume in heartbeat trigger"
leds: bcm6328: fix signal source assignment for leds 4 to 7
This reverts commit 5ab92a7cb8.
System cannot enter suspend mode because of heartbeat led trigger.
In autosleep_wq, try_to_suspend function will try to enter suspend
mode in specific period. it will get wakeup_count then call pm_notifier
chain callback function and freeze processes.
Heartbeat_pm_notifier is called and it call led_trigger_unregister to
change the trigger of led device to none. It will send uevent message
and the wakeup source count changed. As wakeup_count changed, suspend
will abort.
Fixes: 5ab92a7cb8 ("leds: handle suspend/resume in heartbeat trigger")
Signed-off-by: Zhang Bo <bo.zhang@nxp.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Each nibble represents 4 LEDs, and in case of the higher register, bit 0
represents LED 4, so we need to use modulus for the LED number as well.
Fixes: fd7b025a23 ("leds: add BCM6328 LED driver")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
media fixes for v4.12-rc4
* tag 'media/v4.12-2': (598 commits)
[media] rc-core: race condition during ir_raw_event_register()
[media] cec: drop MEDIA_CEC_DEBUG
[media] cec: rename MEDIA_CEC_NOTIFIER to CEC_NOTIFIER
[media] cec: select CEC_CORE instead of depend on it
[media] rainshadow-cec: ensure exit_loop is intialized
[media] atomisp: don't treat warnings as errors
Linux 4.12-rc3
x86/ftrace: Make sure that ftrace trampolines are not RWX
x86/mm/ftrace: Do not bug in early boot on irqs_disabled in cpu_flush_range()
selftests/ftrace: Add a testcase for many kprobe events
kprobes/x86: Fix to set RWX bits correctly before releasing trampoline
ftrace: Fix memory leak in ftrace_graph_release()
ipv4: add reference counting to metrics
net: ethernet: ax88796: don't call free_irq without request_irq first
ip6_tunnel, ip6_gre: fix setting of DSCP on encapsulated packets
sctp: fix ICMP processing if skb is non-linear
net: llc: add lock_sock in llc_ui_bind to avoid a race condition
PCI/msi: fix the pci_alloc_irq_vectors_affinity stub
blk-mq: Only register debugfs attributes for blk-mq queues
x86/timers: Move simple_udelay_calibration past init_hypervisor_platform
...
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This both simplifies the code because we can drop the workqueue
indirection, and it enables using the trigger for GPIOs that work with
threaded IRQs themselves.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
The driver checks an incorrect flag of functionality of adapter.
When a driver requires i2c_smbus_read_byte_data and
i2c_smbus_write_byte_data, it should check I2C_FUNC_SMBUS_BYTE_DATA
instead I2C_FUNC_I2C.
This patch fixes the problem.
Signed-off-by: Tin Huynh <tnhuynh@apm.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
All users of the Versatile LED driver are deleted and replaced
with the very generic leds-syscon. Delete the old driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Add a new DT property, nxp,inverted-out, to invert the polarity
of the output.
Tested on PCA9634.
Signed-off-by: Anders Darander <anders@chargestorm.se>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
This patch extends the device tree support for the pca9532 by adding
the leds 'default-state' property.
Signed-off-by: Felix Brack <fb@ltec.ch>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Motorola CPCAP is a PMIC (power management integrated circuit) found
in multiple smartphones. This driver adds support for the chip's LED
controllers. This introduces support for all controllers used by the
Droid 4. According to Motorola's driver (no datasheets available)
there a couple of more LED controllers. I did not add support for
them, since I cannot verify that they work with my modifications.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
In ACPI world any ID should be carefully chosen and registered
officially. The discussion [1] as I read it gets to wilful assignment
an ID for non-existing real DSDT example.
Rafael already told [2] how this device would be enumerated using
compatible string. To be more precise look at the possible DSDT excerpt
below:
Device (LDX0) {
Name (_HID, "PRP0001")
Name (_DDN, "TI LP3952 compatible led driver")
...
})
Name (_DSD, Package () {
ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package () {
Package () {"compatible", "ti,lp3952"},
...
}
})
Based on above, remove non-official ACPI IDs and enumeration from the
driver.
Note: currently driver has no compatible strings at all, to make above
working one should add at least one.
[1] https://e2e.ti.com/support/power_management/led_driver/f/192/t/524926
[2] https://www.spinics.net/lists/linux-acpi/msg67125.html
Cc: Tony Makkiel <tony.makkiel@daqri.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
It should be ">= MT6323_MAX_LEDS" instead of ">". Also "reg" is a u32
so it can't be negative and we can remove the test for negative values.
Fixes: 216ec6cc4c ("leds: Add LED support for MT6323 PMIC")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
MT6323 PMIC is a multi-function device that includes LED function.
It allows attaching up to 4 LEDs which can either be on, off or dimmed
and/or blinked with the controller.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
In leds-gpio we support LEDs specified in DT so we should use
(devm_)of_led_classdev_register. This allows passing DT node as argument
for use by the LED subsystem.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
These new functions allow passing an additional device_node argument
that will be internally set for created LED device. Thanks to this LED
core code and triggers will be able to access DT node for reading extra
info.
The easiest solution for achieving this was reworking old functions to
more generic ones & adding simple defines for API compatibility.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
The dell-led driver handles a specific WMI GUID present on some Dell
laptops and as such it belongs in the x86 platform driver subsystem.
Source code is moved along with the relevant Kconfig and Makefile
entries, with some minor modifications:
- Kconfig option is renamed from CONFIG_LEDS_DELL_NETBOOKS to
CONFIG_DELL_WMI_LED,
- the X86 Kconfig dependency is removed as the whole
drivers/platform/x86 menu depends on it, so there is no need to
duplicate it,
- the name of the module's source file is removed from the header
comment to avoid the need to update it in the future.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Tested-by: Alex Hung <alex.hung@canonical.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
With dell_micmute_led_set() moved to drivers/platform/x86/dell-laptop.c,
all remnants of the mic mute LED handling code can be removed from
drivers/leds/dell-led.c, restoring it back to the state it was in before
commit db6d8cc007 ("dell-led: add mic mute led interface").
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Tested-by: Alex Hung <alex.hung@canonical.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Linus Torvalds
Colin Ian King
Mauro Carvalho Chehab
Paul Burton
Zhang Bo
Jonas Gorski
Sakari Ailus
Jan Kiszka
Tin Huynh
Linus Walleij
Anders Darander
Stephen Boyd
Felix Brack
Sebastian Reichel
Andy Shevchenko
Dan Carpenter
Sean Wang
Rafał Miłecki
Michał Kępień