If we're going to run the handler from free_irq() then we must do it with
local irq's disabled. Otherwise lockdep complains that the handler is taking
irq-safe spinlocks in a non-irq-safe fashion.
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The serial_pci driver tries to guess serial ports on unknown devices based
on the PCI class (modem or serial). On certain softmodems (AC'97 modems)
this can lead to the recognition of non-existing serial ports.
This patch adds a blacklist of PCI IDs that are to be ignored by the driver.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Christian Schmidt <schmidt@digadd.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Cc: Yinghai Lu <yinghai.lu@sun.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reading the LSR clears the break, parity, frame error, and overrun bits in
the 8250 chip, but these are not being saved in all places that read the
LSR. Same goes for the MSR delta bits. Save the LSR bits off whenever the
lsr is read so they can be handled later in the receive routine. Save the
MSR bits to be handled in the modem status routine.
Also, clear the stored bits and clear the interrupt registers before
enabling interrupts, to avoid handling old values of the stored bits in the
interrupt routines.
[akpm@linux-foundation.org: clean up pre-existing code]
Signed-off-by: Corey Minyard <minyard@acm.org>
Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Cc: Yinghai Lu <yinghai.lu@sun.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The uart_set_termios() function will bail out early without bothering to
touch the hardware, if it decides that nothing "relevant" has changed.
Unfortunately, its idea of "relevant" doesn't include c_[io]speed. So if
the baud rate bits are BOTHER and you just change the speed, the change
gets optimised away.
This patch makes it ignore the old Bfoo bits in c_cflag and just check
whether c_ispeed and c_ospeed have changed. Those integers are always set
appropriately for us by set_termios().
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Alan Cox <alan@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I couldn't find any memory policy documentation in the Documentation
directory, so here is my attempt to document it.
There's lots more that could be written about the internal design--including
data structures, functions, etc. However, if you agree that this is better
that the nothing that exists now, perhaps it could be merged. This will
provide a baseline for updates to document the many policy patches that are
currently being worked.
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Acked-by: Rob Landley <rob@landley.net>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix up the maintainers info in the tpm drivers. Kylene will be out for
some time, so copying the sourceforge list is the best way to get some
attention.
Cc: Marcel Selhorst <tpm@selhorst.net>
Cc: Kylene Jo Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Booting SPARSEMEM on NUMA systems trips a BUG in page_alloc.c:
Initializing HighMem for node 0 (00038000:00100000)
Initializing HighMem for node 1 (00100000:001ffe00)
------------[ cut here ]------------
kernel BUG at /home/apw/git/linux-2.6/mm/page_alloc.c:456!
[...]
This occurs because the section to node id mapping is not being
setup correctly during init under SPARSEMEM_STATIC, leading to an
attempt to free pages from all nodes into the zones on node 0.
When the zone_table[] was removed in the following commit, a new
section to node mapping table was introduced:
commit 89689ae7f9
[PATCH] Get rid of zone_table[]
That conversion inadvertantly only initialised the node mapping in
SPARSEMEM_EXTREME. Ensure we initialise the node mapping in
SPARSEMEM_STATIC.
[akpm@linux-foundation.org: make the stubs static inline]
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Cc: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When ecryptfs_lookup() is called against special files, eCryptfs generates
the following errors because it tries to treat them like regular eCryptfs
files.
Error opening lower file for lower_dentry [0xffff810233a6f150], lower_mnt [0xffff810235bb4c80], and flags [0x8000]
Error opening lower_file to read header region
Error attempting to read the [user.ecryptfs] xattr from the lower file; return value = [-95]
Valid metadata not found in header region or xattr region; treating file as unencrypted
For instance, the problem can be reproduced by the steps below.
# mkdir /root/crypt /mnt/crypt
# mount -t ecryptfs /root/crypt /mnt/crypt
# mknod /mnt/crypt/c0 c 0 0
# umount /mnt/crypt
# mount -t ecryptfs /root/crypt /mnt/crypt
# ls -l /mnt/crypt
This patch fixes it by adding a check similar to directories and
symlinks.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Acked-by: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The k8t_sound_hostbridge PCI quick fires on my motherboard (Jetway
K8M8MS) while it shouldn't: the on-board sound chip is not disabled
and is working just fine. Looking at the code, I see that we are
running the quirk for two distinct register values (0x88 and 0xc8)
and then clear bit 6 (0x40). However value 0x88 already has bit 6
cleared so this is a no-op. This is what happens on my board. Thus I
believe that the quirk should only be run for register value 0xc8.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[PATCH] PCI: make pcie_get_readrq visible in pci.h
pcie_get_readrq() is EXPORT_SYMBOL'ed, but its prototype is not
visible in pci.h, add it there.
This is needed by some network drivers.
Signed-off-by: Brice Goglin <brice@myri.com>
Acked-by: Peter Oruba <peter.oruba@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adrian Bunk wrote:
> Alois Nešpor wrote
>> PCI: Bus #0b (-#0e) is hidden behind transparent bridge #0a (-#0b) (try 'pci=assign-busses')
>> Please report the result to linux-kernel to fix this permanently"
>>
>> dmesg:
>> "Yenta: Raising subordinate bus# of parent bus (#0a) from #0b to #0e"
>> without pci=assign-busses and nothing with pci=assign-busses.
>
> Bernhard?
Ok, lets kill the message. As Alois Nešpor also saw, that's fixed up by Yenta,
so PCI does not have to warn about it. PCI could still warn about it if
is_cardbus is 0 in that instance of pci_scan_bridge(), but so far I have
not seen a report where this would have been the case so I think we can
spare the kernel of that check (removes ~300 lines of asm) unless debugging
is done.
History: The whole check was added in the days before we had the fixup
for this in Yenta and pci=assign-busses was the only way to get CardBus
cards detected on many (not all) of the machines which give this warning.
In theory, there could be cases when this warning would be triggered and
it's not cardbus, then the warning should still apply, but I think this
should only be the case when working on a completely broken PCI setup,
but one may have already enabled the debug code in drivers/pci and the
patched check would then trigger.
I do not sign this off yet because it's completely untested so far, but
everyone is free to test it (with the #ifdef DEBUG replaced by #if 1 and
pr_debug( changed to printk(.
We may also dump the whole check (remove everything within the #ifdef from
the source) if that's perferred.
On Alois Nešpor's machine this would then (only when debugging) this message:
"PCI: Bus #0b (-#0e) is partially hidden behind transparent bridge #0a (-#0b)"
"partially" should be in the message on his machine because #0b of #0b-#0e
is reachable behind #0a-#0b, but not #0c-#0e.
But that differentiation is now moot anyway because the fixup in Yenta takes
care of it as far as I could see so far, which means that unless somebody
is debugging a totally broken PCI setup, this message is not needed anymore,
not even for debugging PCI.
Ok, here the patch with the following changes:
* Refined to say that the bus is only partially hidden when the parent
bus numbers are not totally way off (outside of) the child bus range
* remove the reference to pci=assign-busses and the plea to report it
We could add a pure source code-only comment to keep a reference to
pci=assign-busses the in case when this is triggered by someone who
is debugging the cause of this message and looking the way to solve it.
From: Bernhard Kaindl <bk@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
remove stale BKL use from drivers/pci/hotplug/cpqphp_ctrl.c.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
quirk_e100_interrupts() is called after PCI controller is initialized
and before PCI bus enumeration is performed. On some powerpc platforms
which modify PCI controller configuration and set different MEM and IO
windows than those set by firmware quirk_e100_interrupt() is causing
kernel panic as it tries to read from device BAR0 offets which at this
time points to a invalid PCI window (set by firmware).
This patch delays the quirk_100_interrupt() to pci_fixup_final phase,
which happens after bus enumeration and before PCI enable and
device driver initialization.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We need pci_bus_find_capability() in some arch/powerpc code so move
the prototype into a header accessible to it.
Also kill the duplicate prototype for pci_bus_alloc_resource().
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as960) removes the error message and stack dump logged by
sysfs_remove_bin_file() when someone tries to remove a nonexistent
file. The warning doesn't seem to be needed, since none of the other
file-, symlink-, or directory-removal routines in sysfs complain in a
comparable way.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Tejun Heo <htejun@gmail.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a Documentation/HOWTO korean version of 2.6.23-rc1
The header is refered to a japanese's one.
From: Minchan Kim <minchan.kim@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Andrew Morton
Christian Schmidt
Corey Minyard
Atsushi Nemoto
Niels de Vos
David Woodhouse
john stultz
Lee Schermerhorn
Adrian Bunk
Kent Yoder
Andy Whitcroft
Ryusuke Konishi
Jean Delvare
Tejun Heo
Brice Goglin
Bernhard Kaindl
Ingo Molnar
Rolf Eike Beer
Marian Balakowicz
Kumar Gala
Alan Stern
Qi Yong
Minchan Kim