Again we don't really support different settings, so don't let the
BIOS sneak stuff through.
Since the motivation for this patch series is to ensure we have the
correct gamma table mode selected also add the required write to the
GAMMA_MODE register to select the 8bit legacy table.
And since I find lowercase letters in #defines offensive, also
bikeshed those.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The specs are a bit unclear whether the per-plane trickle feed disable
control exists on VLV. There is another trickle feed disable control
in the MI_ARB register.
After some experimentation it turns out both the DSPCNTR trickle feed
bits and the MI_ARB bit can be toggled. However the DSPCNTR bits don't
seem to have any effect.
The MI_ARB bit, on the other hand, has a noticable effect. I performed
an experiment where I reduced the FIFO size via DSPARB and observed the
effect of the MI_ARB trickle feed bit on the display.
Using a 1920x1080-60 mode, with MI_ARB=0x4 the display started to have
problems with DSPARB=0x42424242, whereas with MI_ARB=0x0 the problems
didn't start until DSPARB=0x09090909. This seems to confirm that the
MI_ARB trickle feed bit actually does work.
So replace the use of the DSPCNTR trickle feed bits with MI_ARB
on VLV.
v2: Amend commit message with results from experimentation
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Using ids in register macros is much more common in our driver. Also
this way we can reduce the platform specific stuff a bit.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The bits are evenly space, so we can cut down on two big switch
blocks. This also greatly simplifies the hw state readout which
follows in the next patch.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
WaFbcNukeOn3DBlt for IVB, HSW.
According BSPec: "Workaround: Do not enable Render Command Streamer tracking for FBC.
Instead insert a LRI to address 0x50380 with data 0x00000004 after the PIPE_CONTROL that
follows each render submission."
v2: Chris noticed that flush_domains check was missing here and also suggested to do
LRI only when fbc is enabled. To avoid do a I915_READ on every flush lets use the
module parameter check.
v3: Adding Wa name as Damien suggested.
v4: Ville noticed VLV doesn't support fbc at all and comment came wrong from spec.
v5: Ville noticed than on blt a Cache Clean LRI should be used instead the Nuke one.
v6: Check for flush domain on blt (by Ville).
Check for scanout dirty (by Chris).
v7: Apply proper fbc_dirty implemented by Chris.
v8: remove unused variables.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix the DSPCLK_GATE_D access for VLV. The code incorrectly tried to
poke at the ILK+ version of the register which is at the wrong offset.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Intermediate Pixel Storage is a feature that should reduce the number
of times the display engine wakes up memory to read pixels, so it
should allow deeper PC states. IPS can only be enabled on ULT pipe A
with 8:8:8 pipe pixel formats.
With eDP 1920x1080 and correct watermarks but without FBC this moves
my PC7 residency from 2.5% to around 38%.
v2: - It's tied to pipe A, not port A
- Add pipe_config support (Chris)
- Add some assertions (Chris)
- Rebase against latest dinq
v3: - Don't ever set ips_enabled to false (Daniel)
- Only check for ips_enabled at hsw_disable_ips (Daniel)
v4: - Add hsw_compute_ips_config (Daniel)
- Use the new dump_pipe_config (Daniel)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Similar to a patch originally written by:
v2: Reversed the meanings of masked and enabled (Haihao)
Made non-destructive writes in case enable/disabler rps runs first
(Haihao)
v3: Reword error message (Damien)
Modify postinstall to do the right thing based on previous fixup. (Ben)
CC: Xiang, Haihao <haihao.xiang@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The motivation here is we're going to add some new interrupt definitions
and handling outside of the GT interrupts which is all we've managed so
far (with some RPS exceptions). By consolidating the names in the future
we can make thing a bit cleaner as we don't need to define register
names twice, and we can leverage pretty decent overlap in HW registers
since ILK.
To explain briefly what is in the comments: there are two sets of
interrupt masking/enabling registers. At least so far, the definitions
of the two sets overlap. The old code setup distinct names for
interrupts in each set, ie. one for global, and one for ring. This made
things confusing when using the wrong defines in the wrong places.
rebase: Modified VLV bits
v2: Renamed GT_RENDER_MASTER to GT_RENDER_CS_MASTER (Damien)
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
PM interrupts have an expanded role on HSW. It helps route the EBOX
interrupts. This patch is necessary to make the existing code which
touches the mask, and enable registers more friendly to other code paths
that also will need these registers.
To be more explicit:
At preinstall all interrupts are masked and disabled. This implies that
preinstall should always happen before any enabling/disabling of RPS or
other interrupts.
The PMIMR is touched by the workqueue, so enable/disable touch IER and
IIR. Similarly, the code currently expects IMR has no use outside of the
RPS related interrupts so they unconditionally set 0, or ~0. We could
use IER in the workqueue, and IMR elsewhere, but since the workqueue
use-case is more transient the existing usage makes sense.
Disable RPS events:
IER := IER & ~GEN6_PM_RPS_EVENTS // Disable RPS related interrupts
IIR := GEN6_PM_RPS_EVENTS // Disable any outstanding interrupts
Enable RPS events:
IER := IER | GEN6_PM_RPS_EVENTS // Enable the RPS related interrupts
IIR := GEN6_PM_RPS_EVENTS // Make sure there were no leftover events
(really shouldn't happen)
v2: Shouldn't destroy PMIIR or PMIMR VEBOX interrupt state in
enable/disable rps functions (Haihao)
v3: Bug found by Chris where we were clearing the wrong bits at rps
disable.
expanded commit message
v4: v3 was based off the wrong branch
v5: Added the setting of PMIMR because of previous patch update
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We were previously only setting the WM_PIPE registers, now we are
setting the LP watermark registers. This should allow deeper PC
states, resulting in power savings.
We're only using 1/2 data buffer partitioning for now.
v2: Merge both hsw_compute_pri_wm_* functions (Ville)
v3: - Simplify hsw_compute_wm_results (Ville)
- Rebase due to changes on the previous patch
v4: Unconfuse wm_lp/level (Ville)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We were previously calling sandybridge_update_wm on HSW, but the SNB
function didn't really match the HSW specification, so we were just
writing the wrong values.
With this patch, the haswell_update_wm function will set the correct
values for the WM_PIPE registers, but it will still keep all the LP
watermarks disabled.
The patch may look a little bit over-complicated for now, but it's
because much of the infrastructure for setting the LP watermarks is
already in place, so we won't have too much code churn on the patch
that sets the LP watermarks.
v2: - Fix pixel_rate on panel fitter case (Ville)
- Try to not overflow (Ville)
- Remove useless variable (Ville)
- Fix p->pri_horiz_pixels (Paulo)
v3: - Fix rounding errors on hsw_wm_method2 (Ville)
v4: - Fix memcmp bug (Paulo)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Like the other rings, the VECS supports semaphores. The semaphore stuff
is a bit wonky so this patch on it's own should be nice for review.
This patch should have no functional impact.
v2: Fix the English parts of clarification (again, register names were
right, text was reversed) (Damien)
Restore the still valid invariant. (Damien)
The bsd semaphore register should be MI_SEMAPHORE_SYNC_VVE (Damien)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This replaces the existing MBOX update code with a more generalized
calculation for emitting mbox updates. We also create a sentinel for
doing the updates so we can more abstractly deal with the rings.
When doing MBOX updates the code must be aware of the /other/ rings.
Until now the platforms which supported semaphores had a fixed number of
rings and so it made sense for the code to be very specialized
(hardcoded).
The patch does contain a functional change, but should have no
behavioral changes.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Semaphores are tied very closely to the rings in the GPU. Trivial patch
adds comments to the existing code so that when we add new rings we can
include comments there as well. It also helps distinguish the ring to
semaphore mailbox interactions by using the ringname in the semaphore
data structures.
This patch should have no functional impact.
v2: The English parts (as opposed to register names) of the comments
were reversed. (Damien)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Both the intel_dpio_{read,write} and valleyview_{punit,nc}_{read,write}
use the IOSF sideband interface. They access the same registers and do
mostly the same stuff, but no shared code. There are even duplicate
register defines for the same registers. Both have locking, but the
former use dpio_lock and the latter rps.hw_lock. It's racy.
This patch refactors the sideband access to a single function that
expects dpio_lock to be held. The dpio_lock is only used for sideband
stuff, so it's a better match than rps.hw_lock for the purpose. The rps
stuff still needs rps.hw_lock, since it's used to protect more than just
the register access, so rps code will need to hold both locks.
Based on the work by Shobhit Kumar <shobhit.kumar@intel.com> and Yogesh
Mohan Marimuthu <yogesh.mohan.marimuthu@intel.com>.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Commit 1544d9d573 added a workaround
inside haswell_init_clock_gating and mentioned it is "a workaround for
early silicon revisions and should be removed later". This workaround
is documented in bit 31 of PRI_CTL. I asked Arthur and he mentioned
that setting FORCE_ARB_IDLE_PLANES replaces that workaround for the
newer machines. So use the new one.
Also notice that there's still another workaround for PRI_CTL that
involves WM_DBG, but it's not the one we're reverting. And notice that
we were previously setting WM_DBG_DISALLOW_MULTIPIPE_LP which disables
the LP watermarks when more than one pipe is used, and we really don't
want this because we need the LP watermarks if we want to reach deeper
PC states.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add a comment for the w/a name Ville dug out of Bspec.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge Linux 3.10-rc2 since the various (rather trivial) conflicts
grew a bit out of hand. intel_dp.c has the only real functional
conflict since the logic changed while dev_priv->edp.bpp was moved
around.
Also squash in a whitespace fixup from Ben Widawsky for
i915_gem_gtt.c, git seems to do something pretty strange in there
(which I don't fully understand tbh).
Conflicts:
drivers/gpu/drm/i915/i915_reg.h
drivers/gpu/drm/i915/intel_dp.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Display register 46500h bit 23 must be set to 1b for the entire time that
Frame Buffer Compression is enabled.
v2: Ville suggested to enable it back when disabling fbc to avoid wasting
power.
v3: RMW to preserve other bits (by Ville)
v4: Fix from Ville: sed &/| at RMW
v5: Too far on sed.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Insert missing space that checkpatch spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch introduce Frame Buffer Compression (FBC) support for IVB,
without enabling it by default.
It adds a new function gen7_enable_fbc to avoid getting
ironlake_enable_fbc messed with many IS_IVYBRIDGE checks.
v2: Fixes from Ville.
* Fix Plane. FBC is tied to primary plane A in HSW
* Fix DPFC initial write to avoid let trash on the register.
v3: Checking for bad plane on intel_update_fbc() as Chris suggested.
v4: Ville pointed out that according to BSpec FBC_CTL bits 0:3 must be 0.
v5: Up to v4 this work was entirely focused on Haswell. However Ville
noticed I could reuse the FBC work done for HSW and get FBC for free
at Ivybridge. So it makes more sense enable FBC for IVB first.
FBC for HSW comming on next patches. We are just not enabling it by
default on IVB.
v6: Fix confused commit name (by Matt Turner).
v7: Remove gtt_offset shift since it is page aligned byte offset (by Ville).
Cc: Matt Turner <mattst88@gmail.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä
Daniel Vetter
Rodrigo Vivi
Paulo Zanoni
Ben Widawsky
Jani Nikula