Each routing protocol has its own metric semantic and
therefore is the protocol itself the only component able to
compare two metrics to check their "similarity".
This new API allows each routing protocol to implement its
own logic and make the external code protocol agnostic.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
This new API allows to compare the two neighbours based on
the metric avoiding the user to deal with any routing
algorithm specific detail
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
A TT response may be prepared and sent while the local or
global translation table is getting updated.
The worst case is when one of the tables is accessed after
its content has been recently updated but the metadata
(TTVN/CRC) has not yet. In this case the reader will get a
table content which does not match the TTVN/CRC.
This will lead to an inconsistent state and so to a TT
recovery.
To avoid entering this situation, put a lock around those TT
operations recomputing the metadata and around the TT
Response creation (the latter is the only reader that
accesses the metadata together with the table).
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Since batman-adv is now fully VLAN-aware, a proper framework
able to handle per-vlan-interface attributes is needed.
Those attributes will affect the associated VLAN interface
only, rather than the real soft_iface (which would result
in every vlan interface having the same attribute
configuration).
To make the code simpler and easier to extend, attributes
associated to the standalone soft_iface are now treated
like belonging to yet another vlan having a special vid.
This vid is different from the others because it is made up
by all zeros and the VLAN_HAS_TAG bit is not set.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
To make the translation table code VLAN-aware, each entry
must carry the VLAN ID which it belongs to. This patch adds
such attribute to the related TT structures.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
The module prints a warning when the MTU on the hard interface is too
small to transfer payload traffic without fragmentation. The required
MTU is calculated based on the encapsulation header size. If network
coding is compild into the module its header size is taken into
account as well.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
the icmp and the icmp_rr packets share the same initial
fields since they use the same code to be processed and
forwarded.
Extract the common fields and put them into a separate
struct so that future ICMP packets can be easily added
without bloating the packet definition.
However, keep the seqno field outside of the newly created
common header because future ICMP types may require a
bigger sequence number space.
This change breaks compatibility due to fields reordering
in the ICMP headers.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Fragments arriving at their destination are buffered for later merge.
Merged packets are passed to the main receive function as had they never
been fragmented.
Fragments are forwarded without merging if the MTU of the outgoing
interface is smaller than the size of the merged packet.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Remove the existing fragmentation code before adding the new version
and delete unicast.{h,c}.
batadv_unicast_send_skb() is moved to send.c and renamed to
batadv_send_skb_unicast().
fragmentation entry in sysfs (bat_priv->fragmentation) is kept for use in
the new fragmentation code.
BATADV_UNICAST_FRAG packet type is renamed to BATADV_FRAG for use in the
new fragmentation code.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Reordering the packet type numbers allows us to handle unicast
packets in a general way - even if we don't know the specific packet
type, we can still forward it. There was already code handling
this for a couple of unicast packets, and this is the more
generalized version to do that.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Since we removed the __packed from most of the packets, we should
make sure that the offset generated by the compiler are correct for
sent/received data.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Instead of generating roaming specific packets the TVLV unicast API is
used to send roaming information.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Instead of generating TT specific packets the TVLV unicast API is used
to send translation table data.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Prior to this patch batman-adv read the advertised uplink bandwidth
from userspace and compressed this information into a single byte
called "gateway class".
Now the download & upload bandwidth information is sent as-is. No
userspace change is necessary since the sysfs API always allowed
to specify a bandwidth.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Spyros Gasteratos <morfeas3000@gmail.com>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
The goal is to provide the infrastructure for sending, receiving and
parsing information 'containers' while preserving backward
compatibility. TVLV (based on the commonly known Type Length Value
technique) was chosen as the format for those containers. Even if a
node does not know the tvlv type of a certain container it can simply
skip the current container and proceed with the next. Past experience
has shown features evolve over time, so a 'version' field was added
right from the start to allow differentiating between feature
variants - hence the name: T(ype) V(ersion) L(ength) V(alue).
This patch introduces the basic TVLV infrastructure:
* register / unregister tvlv containers to be sent with each OGM
(on primary interfaces only)
* register / unregister callback handlers to be called upon
finding the corresponding tvlv type in a tvlv buffer
* unicast tvlv send / receive API calls
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Spyros Gasteratos <morfeas3000@gmail.com>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
batman-adv saves its table of packet handlers as a global state, so handlers
must be set up only once (and setting them up a second time will fail).
The recently-added network coding support tries to set up its handler each time
a new softif is registered, which obviously fails when more that one softif is
used (and in consequence, the softif creation fails).
Fix this by splitting up batadv_nc_init into batadv_nc_init (which is called
only once) and batadv_nc_mesh_init (which is called for each softif); in
addition batadv_nc_free is renamed to batadv_nc_mesh_free to keep naming
consistent.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
The skb priority field may help the wireless driver to choose the right
queue (e.g. WMM queues). This should be set in batman-adv, as this
information is only available here.
This patch adds support for IPv4/IPv6 DS fields and VLAN PCP. Note that
only VLAN PCP is used if a VLAN header is present. Also initially set
TC_PRIO_CONTROL only for self-generated packets, and keep the priority
set by higher layers.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Callers of skb_seq_read() are currently forced to call skb_abort_seq_read()
even when consuming all the data because the last call to skb_seq_read (the
one that returns 0 to indicate the end) fails to unmap the last fragment page.
With this patch callers will be allowed to traverse the SKB data by calling
skb_prepare_seq_read() once and repeatedly calling skb_seq_read() as originally
intended (and documented in the original commit 677e90eda), that is, only call
skb_abort_seq_read() if the sequential read is actually aborted.
Signed-off-by: Wedson Almeida Filho <wedsonaf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On errors in batadv_mesh_init(), bat_counters will be freed in both
batadv_mesh_free() and batadv_softif_init_late(). This patch fixes this
by returning earlier from batadv_softif_init_late() in case of errors in
batadv_mesh_init() and by setting bat_counters to NULL after freeing.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
nc_worker accesses the originator table during its periodic
work, but since the originator table is freed before
stopping the worker this leads to a global protection fault.
Fix this by killing the worker (in nc_free) before freeing
the originator table.
Moreover tidy up the entire clean up routine by running all
the subcomponents freeing procedures first and then killing
the TT and the originator tables at the end.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
batadv_param_set_ra() strips the trailing '\n' from the supplied
string buffer without checking the length of the buffer first. This
patches avoids random memory access and associated potential
crashes.
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
drivers/net/ethernet/intel/igb/igb_main.c
drivers/net/wireless/brcm80211/brcmsmac/mac80211_if.c
include/net/scm.h
net/batman-adv/routing.c
net/ipv4/tcp_input.c
The e{uid,gid} --> {uid,gid} credentials fix conflicted with the
cleanup in net-next to now pass cred structs around.
The be2net driver had a bug fix in 'net' that overlapped with the VLAN
interface changes by Patrick McHardy in net-next.
An IGB conflict existed because in 'net' the build_skb() support was
reverted, and in 'net-next' there was a comment style fix within that
code.
Several batman-adv conflicts were resolved by making sure that all
calls to batadv_is_my_mac() are changed to have a new bat_priv first
argument.
Eric Dumazet's TS ECR fix in TCP in 'net' conflicted with the F-RTO
rewrite in 'net-next', mostly overlapping changes.
Thanks to Stephen Rothwell and Antonio Quartulli for help with several
of these merge resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
On a multi-mesh node (a node running more than one batman-adv
virtual interface) batadv_is_my_mac() has to check MAC
addresses of hard interfaces belonging to the current mesh
only.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
As reported by checkpatch, seq_puts has to be preferred with
respect to seq_printf when the format is a constant string
(no va_args)
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Antonio Quartulli
Marek Lindner
Martin Hundebøll
Simon Wunderlich
Simon Wunderlich
Matthias Schiffer
Simon Wunderlich
Wedson Almeida Filho
Antonio Quartulli
David S. Miller