Sony laptops apparently write 4-bytes (rather than 1 byte)
to debug port 0x80, which spews error messages:
Denied AML access to port 0x00000080/4 (DMA1 0x0081-0x0083) [20090320]
http://bugzilla.kernel.org/show_bug.cgi?id=13036
Signed-off-by: Len Brown <len.brown@intel.com>
Asus boards have an ACPI interface for interacting with the hwmon (fan,
temperatures, voltages) subsystem; this driver exposes the relevant
information via the standard sysfs interface.
There are two different ACPI interfaces:
- an old one (based on RVLT/RFAN/RTMP)
- a new one (GGRP/GITM)
Both may be present but there a few cases (my board, sigh) where the
new interface is just an empty stub; the driver defaults to the old one
when both are present.
The old interface has received a considerable testing, but I'm still
awaiting confirmation from my tester that the new one is working as
expected (hence the debug code is still enabled).
Currently all the attributes are read-only, though a (partial) control
should be possible with a bit more work.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
If both the 32-bit and 64-bit addresses are non-null, use the
32-bit address. Provides Windows compatibility.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Use the 32-bit register addresses whenever they are non-zero. This
means that the 32-bit addresses are favored over the 64-bit
(GAS) addresses. The 64-bit addresses are only used if the 32-bit
addresses are zero. This change provides compatibility with all
versions of Windows. The worst case that this solves is when both
the 32-bit and 64-bit addresses are non-zero, but only the 32-bit
addresses are actually valid. This appears to happen in some
BIOSes because in this case, Windows uses the 32-bit addresses.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
One entry in the protected port table eliminated. Added extra
comments to describe each table entry.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This interface is no longer necessary. Requests should be validated
on a per-field basis, not on the entire operation region.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
As per the ACPI specification, preserve (read/modify/write) all
bits that are defined as either reserved or ignored (PM control
control registers only.)
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Ignored bits must be preserved according to the ACPI spec.
Usually this means a read/modify/write when writing to the
register. However, for status registers, writing a one means
clear the event. Writing a zero means preserve the event (do not
clear.) This behavior is clarified in the ACPI 4.0 spec, and the
ACPICA code now simply always writes a zero to the ignored bit.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Added a reader/writer locking mechanism to allow multiple
concurrent namespace walks (readers), but a dynamic table unload
will have exclusive access to the namespace. This fixes a problem
where a table unload could delete the portion of the namespace that
is currently being examined by a walk. Adds a new file, utlock.c
that implements the reader/writer lock mechanism. ACPICA BZ 749.
http://www.acpica.org/bugzilla/show_bug.cgi?id=749
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Incorrect register length mismatch between the 32 and 64 bit
registers in some cases. Code was was checking the wrong pointer
for non-zero, should be looking at the address within the GAS
structure.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Update code for acpi_read_bit_register and acpi_write_bit_register.
Simplified code path, condensed duplicate code.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Rename acpi_get_register and acpi_set_register to clarify the
purpose of these functions. New names are acpi_read_bit_register
and acpi_write_bit_register.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Removed locking for reads from the ACPI bit registers in PM1
Status, Enable, Control, and PM2 Control. The lock is not required
when reading the single-bit registers. The acpi_get_register_unlocked
function is no longer needed and has been removed. This will
improve performance for reads on these registers. ACPICA BZ 760.
http://www.acpica.org/bugzilla/show_bug.cgi?id=760
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Removed some of the extraneous debug prints using the DB_INFO
level. This should make the DB_INFO more useful.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Len Brown
Luca Tettamanti
Bob Moore
Lin Ming