Introduce the MACHINE_IS_LPAR flag for code that should only be
executed if Linux is running in an LPAR.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Finally move it to the place where it belongs to and make get rid of
it for !CONFIG_SMP.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
smp_processor_id() is supposed to work before setup_arch() gets called.
Before that smp_processor_id() may return just an arbitrary value that
is contained in the uninitialized boot lowcore.
So provide the arch function which will override the weak function in
init/main.c.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The TIF_USEDFPU bit is always 0 for s390 and it is not tested anywhere.
Remove the bit. At the same time remove the calls to clear_used_math()
as well. The PF_USED_MATH bit is never set for s390 either.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce user_mode to replace the two variables switch_amode and
s390_noexec. There are three valid combinations of the old values:
1) switch_amode == 0 && s390_noexec == 0
2) switch_amode == 1 && s390_noexec == 0
3) switch_amode == 1 && s390_noexec == 1
They get replaced by
1) user_mode == HOME_SPACE_MODE
2) user_mode == PRIMARY_SPACE_MODE
3) user_mode == SECONDARY_SPACE_MODE
The new kernel parameter user_mode=[primary,secondary,home] lets
you choose the address space mode the user space processes should
use. In addition the CONFIG_S390_SWITCH_AMODE config option
is removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use a console_initcall() to initialize the s390 virtio console and
clean up s390 console initialization in setup.c.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
setup_arch() unconditionally sets the preferred console to ttyS.
This breaks the use of 3270 devices as the console. Provide a new
function to set the default preferred console for s390. The preferred
console depends on the conmode parameter that is used to switch
between 3270 and 3215 terminal/console mode.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Start the cpu time accounting very early to catch the cpu time spent
for the initial kernel setup. To make the output of /proc/uptime
match the sum of all cpu accounting values of the boot cpu reset
xtime and wall_to_monotonic to sane values based on the TOD clock.
The values set by timekeeping_init are off by up to a second.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently the storage of the machine flags is a globally exported unsigned
long long variable. By moving the storage location into the lowcore struct we
allow assembler code to check machine_flags directly even without needing a
register. Addtionally the lowcore and therefore the machine flags too will be
in cache most of the time.
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The Extended Translation Facility 3 (ETF3) added instructions which
allow conversions between different unicode character maps (UTF-8,
UTF-32 ...). These instructions got enhanced with a later version of
the ETF3 allowing malformed multibyte chars to be recognized and
reported correctly. The attached patch reserves bit 8 in the elf
hwcaps vector for the enhanced version of ETF3. The bit corresponds to
the stfle bits 22 and 30 and will only be set if both of the stfle
bits are set.
Signed-off-by: Andreas Krebbel <krebbel@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The old dfp detection wanted to check bit 43 (dfp high performance), but due
to a wrong calculation always used to check bit 42. Additionally the
"userspace expectation" is, that the dfp capability bit is set is if facility
bit 42 (decimal floating point facility available) and bit 44 (perform floating
point operation facility avail).
The patch fixes the bit calculation and extends the check to work like:
elf hw cap dfp bit = facility bits 42 (dfp) & 44 (pfpo) available
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The zcore code switches to real addressing mode when creating a kernel dump.
This is not possible, if it is built as a kernel module. With this patch
zcore (zfcpdump) can't be built as a kernel module any more.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Disable switch_amode by default because pagetable walk on pre z9
hardware has negative performance impact.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Standby memory detected with the sclp interface gets always registered
with add_memory calls without considering the limitationt that the
"mem=" kernel paramater implies.
So fix this and only register standby memory that is below the specified
limit.
This fixes zfcpdump since it uses "mem=32M". In case there is appr.
2GB standby memory present all of usable memory would be used for the
struct pages needed for standby memory.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The extract cpu time instruction (ectg) instruction allows the user
process to get the current thread cputime without calling into the
kernel. The code that uses the instruction needs to switch to the
access registers mode to get access to the per-cpu info page that
contains the two base values that are needed to calculate the current
cputime from the CPU timer with the ectg instruction.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Martin Schwidefsky
Heiko Carstens
Hendrik Brueckner
Christian Ehrhardt
Andreas Krebbel
Stoyan Gaydarov
Michael Holzheu
Gerald Schaefer
Frank Munzert