Current base address is wrong by 0x04 bytes for AHB bus device as shown
in dmesg:
tegra-ahb 6000c004.ahb: incorrect AHB base address in DT data - enabling workaround
To correct old DTBs, commit ce7a10b0ff ("ARM: 8334/1: amba: tegra-ahb:
detect and correct bogus base address") checks for the low bit of the
base address and removes theses 0x04 bytes at runtime.
This patch fixes the original DTS, so upstream version doesn't need the
workaround of the base address.
As both addresses are valid, this patch doesn't break compatibility.
Tested on tegra20-paz00 (aka ac100).
Signed-off-by: Nicolas Chauvet <kwizart@gmail.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Cortex-A9 TWD timer has registers at address 0x50040600, but the
unit address was 50004600, most likely a typo.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Pull ARM SoC DT updates part 2 from Arnd Bergmann:
"This is a follow-up to the early ARM SoC DT changes, with additional
content that has external dependencies:
- The Tegra IOMMU DT support depends on changes from the iommu tree,
plus the contents of the arm-soc drivers branch
- The MVEBU PHY support depends on changes from the phy tree
- The AT91 DT support depends on changes from the RTC and DMA-slave
trees
All of these changes just enable additional devices for existing
platforms"
* tag 'dt2-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: tegra: Enable IOMMU for display controllers on Tegra124
ARM: tegra: Enable IOMMU for display controllers on Tegra114
ARM: tegra: Enable IOMMU for display controllers on Tegra30
ARM: tegra: Add memory controller support for Tegra124
ARM: tegra: Add memory controller support for Tegra114
ARM: tegra: Add memory controller support for Tegra30
ARM: tegra: Add APB_MISC_GP as a MIPI pad control bank
ARM: mvebu: add PHY support to the dts for the USB controllers on Armada 375
ARM: mvebu: add Device Tree description of USB cluster controller on Armada 375
ARM: at91/dt: at91sam9g45: add ISI node
ARM: at91/dt: enable the RTT block on the at91sam9m10g45ek board
ARM: at91/dt: enable the RTT block on the sam9g20ek board
ARM: at91/dt: add GPBR nodes
ARM: at91/dt: add RTT nodes to at91 dtsis
ARM: at91/dt: at91sam9rl: add rtc
ARM: at91: fix GPLv2 wording
ARM: at91/dt: sama5d4: add DMA support
ARM: at91/dt: sama5d4: use macro instead of numeric value
Add iommus properties to the device tree nodes for the two display
controllers found on Tegra30. This will allow the display controllers to
map physically non-contiguous buffers to I/O virtual contiguous address
spaces so that they can be used for scan-out.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Collapses the old memory-controller and IOMMU device tree nodes into a
single node to more accurately describe the hardware.
While this is an incompatible change there are no users of the IOMMU on
Tegra, even though a driver has existed for some time.
Signed-off-by: Thierry Reding <treding@nvidia.com>
There are general changes pending to make the /aliases/serial* entries
number the serial ports on the system. On Tegra, so far the ports have
been just numbered dynamically as they are configured so that makes them
change.
To avoid this, add specific aliases per board to keep the old numbers.
This allows us to change the numbering by default on future SoCs while
keeping the numbering on existing boards.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Thierry Reding <treding@nvidia.com>
These nodes are required so that the flow controller driver can obtain
the I/O memory region from device tree rather than hard-coding it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Pull ARM SoC cleanups from Olof Johansson:
"This merge window brings a good size of cleanups on various platforms.
Among the bigger ones:
- Removal of Samsung s5pc100 and s5p64xx platforms. Both of these
have lacked active support for quite a while, and after asking
around nobody showed interest in keeping them around. If needed,
they could be resurrected in the future but it's more likely that
we would prefer reintroduction of them as DT and
multiplatform-enabled platforms instead.
- OMAP4 controller code register define diet. They defined a lot of
registers that were never actually used, etc.
- Move of some of the Tegra platform code (PMC, APBIO, fuse,
powergate) to drivers/soc so it can be shared with 64-bit code.
This also converts them over to traditional driver models where
possible.
- Removal of legacy gpio-samsung driver, since the last users have
been removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some
misc cleanups, etc"
* tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (117 commits)
drivers: CCI: Correct use of ! and &
video: clcd-versatile: Depend on ARM
video: fix up versatile CLCD helper move
MAINTAINERS: Add sdhci-st file to ARCH/STI architecture
ARM: EXYNOS: Fix build breakge with PM_SLEEP=n
MAINTAINERS: Remove Kirkwood
ARM: tegra: Convert PMC to a driver
soc/tegra: fuse: Set up in early initcall
ARM: tegra: Always lock the CPU reset vector
ARM: tegra: Setup CPU hotplug in a pure initcall
soc/tegra: Implement runtime check for Tegra SoCs
soc/tegra: fuse: fix dummy functions
soc/tegra: fuse: move APB DMA into Tegra20 fuse driver
soc/tegra: Add efuse and apbmisc bindings
soc/tegra: Add efuse driver for Tegra
ARM: tegra: move fuse exports to soc/tegra/fuse.h
ARM: tegra: export apb dma readl/writel
ARM: tegra: Use a function to get the chip ID
ARM: tegra: Sort includes alphabetically
ARM: tegra: Move includes to include/soc/tegra
...
Add efuse and apbmisc bindings for Tegra20, Tegra30, Tegra114 and
Tegra124.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add new properties to all of the Tegra PHYs that are now required
according to the binding.
In order to stay compatible with old device trees, the USB drivers
will still function without these reset properties but with the old,
potentially buggy behaviour.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge "ARM: tegra: device tree changes for 3.15" from Stephen Warren:
This enables:
- host1x and eDP support on Tegra124.
- LCD panel support for a few Tegra20 devices and Venice2.
- Enables power down, SPI flash, and USB on Venice2.
- Documents which Dalmore revision is supported.
- Adds an I2C bus mux to Cardhu.
Additionally, Tegra124 is converted to use #address-cells=<2> since the
HW suports more than 32-bits of address space, and various cleanups are
included.
* tag 'tegra-for-3.15-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (21 commits)
ARM: dts: tegra: add PCIe interrupt mapping properties
ARM: tegra: use 2 address cells for Tegra124 DT
ARM: tegra: Rename as3722 node to pmic
ARM: tegra: Fix whitespace around '='
ARM: tegra: Enable USB on Venice2
ARM: tegra: Add Tegra124 USB support
ARM: tegra: Enable eDP for Venice2
ARM: tegra: Add Tegra124 eDP support
ARM: tegra: Add Tegra124 host1x support
ARM: tegra: Hook up SDMMC3 power-supply on Venice2
ARM: tegra: Overhaul Venice2 regulators
ARM: tegra: Combine VBUS enable pins into one node
ARM: tegra: Use "disabled" for status property
ARM: tegra: add SPI flash to Venice2 DT
ARM: tegra: enable PCA9546 on Cardhu
ARM: tegra: enable LCD panel on Ventana
ARM: tegra: enable LCD panel on Seaboard
ARM: tegra: add system-power-controller property for PMIC node
ARM: tegra: document which Dalmore revisions are supported
ARM: tegra: Properly sort clocks property
...
Signed-off-by: Olof Johansson <olof@lixom.net>
The number of the head specifies the index of the display controller
unit and is required to properly configure outputs so that they receive
video data from the correct source.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Other files and nodes list the resets property after the clocks property
so do the same here for consistency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Modify Tegra30 default USB2 phy_type to UTMI; this matches
power-on-reset defaults and is expected to be the common case.
The current implementation is likely an incorrect
carry-over from Tegra20, where USB2 does default to ULPI.
Signed-off-by: Eric Brower <ebrower@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Use Tegra pinconrol dt-binding macro to set the values of different pinmux
properties of Tegra30 platforms.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
DT node names should include a unit address iff the node has a reg
property. For Tegra DTs at least, we were previously applying a different
rule, namely that node names only needed to include a unit address if it
was required to make the node name unique. Consequently, many unit
addresses are missing. Add them.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Now that all Tegra drivers have been converted to use DMA APIs which
retrieve DMA channel information from standard DMA DT properties, we can
remove all the legacy DT DMA-related properties.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Now that all Tegra drivers have been converted to use the common reset
framework, we can remove all the legacy DT clocks/clock-names entries for
"clocks" that were only used with the old custom Tegra module reset API.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
This patch switches the Tegra DT files to use the standard DMA DT bindings
rather than custom properties. Note that the legacy properties are not yet
removed; the drivers must be updated to use the new properties first.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
An earlier patch updated the Tegra DT bindings to require resets and
reset-names properties to be filled in. This patch updates the DT files
to include those properties.
Note that any legacy clocks and clock-names entries that are replaced by
reset properties are not yet removed; the drivers must be updated to use
the new resets and reset-names properties first.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Many of the Tegra DT binding documents say nothing about the clocks or
clock-names properties, yet those are present and required in DT files.
This patch simply updates the documentation file to match the implicit
definition of the binding, based on real-world DT content.
All Tegra bindings that mention clocks are updated to have consistent
wording and formatting of the clock-related properties.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-By: Terje Bergstrom <tbergstrom@nvidia.com>
Tomeu Vizoso
Nicolas Chauvet
Marcel Ziswiler
Marc Zyngier
Thierry Reding
Linus Torvalds
Olof Johansson
Peter De Schrijver
Tuomas Tynkkynen
Lucas Stach
Thierry Reding
Eric Brower
Laxman Dewangan
Stephen Warren