Add support for the Artesyn MVME2500 Single Board Computer.
The MVME2500 is a 6U form factor VME64 computer with:
- A single Freescale QorIQ P2010 CPU
- 1 GB of DDR3 onboard memory
- Three Gigabit Ethernets
- Five 16550 compatible UARTS
- One USB 2.0 port, one SHDC socket and one SATA connector
- One PCI/PCI eXpress Mezzanine Card (PMC/XMC) Slot
- MultiProcessor Interrupt Controller (MPIC)
- A DS1375T Real Time Clock (RTC) and 512 KB of Non-Volatile Memory
- Two 64 KB EEPROMs
- U-Boot in 16 SPI Flash
This patch is based on linux-3.18 and has been boot tested.
Signed-off-by: Alessio Igor Bogani <alessio.bogani@elettra.eu>
Signed-off-by: Scott Wood <scottwood@freescale.com>
On PowerNV platform, the OPAL interrupts are exported by firmware
through device-node property (/ibm,opal::opal-interrupts). Under
some extreme circumstances (e.g. simulator), we don't have this
property found from the device tree. For that case, we shouldn't
allocate the interrupt map. Otherwise, slab complains allocating
zero sized memory chunk.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The patch put the OPAL interrupt setup logic in opal_init() into
seperate function opal_irq_init() for easier code maintaining. The
patch doesn't introduce logic changes except:
* Rename variable names.
* Release virtual IRQ upon error from request_irq().
* Don't cache the virtual IRQ to opal_irqs[] upon error from
request_irq().
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit c8742f8512 "powerpc/powernv: Expose OPAL firmware symbol
map" I added pr_fmt() to opal.c. This left some existing pr_xxx()s with
duplicate "opal" prefixes, eg:
opal: opal: Found 0 interrupts reserved for OPAL
Fix them all up. Also make the "Not not found" message a bit more
verbose.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Remove slice_set_psize() which is not used.
It was added in 3a8247cc2c "powerpc: Only demote individual slices
rather than whole process" but was never used.
Remove vsx_assist_exception() which is not used.
It was added in ce48b21007 "powerpc: Add VSX context save/restore,
ptrace and signal support" but was never used.
Remove generic_mach_cpu_die() which is not used.
Its last caller was removed in 375f561a41 "powerpc/powernv: Always go
into nap mode when CPU is offline".
Remove mpc7448_hpc2_power_off() and mpc7448_hpc2_halt() which are
unused.
These were introduced in c5d56332fd "[POWERPC] Add general support for
mpc7448hpc2 (Taiga) platform" but were never used.
This was partially found by using a static code analysis program called
cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
[mpe: Update changelog with details on when/why they are unused]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When CONFIG_PRINTK=n, log_buf_addr_get() returns NULL and log_buf_len_get()
return 0. Check for these return values and skip registering the dump buffer.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Reviewed-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
RTAS events require arguments be passed in big endian while hypercalls
have their arguments passed in registers and the values should therefore
be in CPU endian.
The "ibm,suspend_me" 'RTAS' call makes a sequence of hypercalls to setup
one true RTAS call. This means that "ibm,suspend_me" is handled
specially in the ppc_rtas() syscall.
The ppc_rtas() syscall has its arguments in big endian and can therefore
pass these arguments directly to the RTAS call. "ibm,suspend_me" is
handled specially from within ppc_rtas() (by calling rtas_ibm_suspend_me())
which has left an endian bug on little endian systems due to the
requirement of hypercalls. The return value from rtas_ibm_suspend_me()
gets returned in cpu endian, and is left unconverted, also a bug on
little endian systems.
rtas_ibm_suspend_me() does not actually make use of the rtas_args that
it is passed. This patch removes the convoluted use of the rtas_args
struct to pass params to rtas_ibm_suspend_me() in favour of passing what
it needs as actual arguments. This patch also ensures the two callers of
rtas_ibm_suspend_me() pass function parameters in cpu endian and in the
case of ppc_rtas(), converts the return value.
migrate_store() (the other caller of rtas_ibm_suspend_me()) is from a
sysfs file which deals with everything in cpu endian so this function
only underwent cleanup.
This patch has been tested with KVM both LE and BE and on PowerVM both
LE and BE. Under QEMU/KVM the migration happens without touching these
code pathes.
For PowerVM there is no obvious regression on BE and the LE code path
now provides the correct parameters to the hypervisor.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The callback (ppc_md.pci_probe_mode()) is used to determine if the
child PCI devices of the indicated PCI bus should be probed from
device-tree or hardware. On PowerNV platform, we always expect
probing PCI devices from hardware, which is PowerPC PCI core's
default behaviour. Also, the callback had some delay implemented
based on PHB's device node property "reset-clear-timestamp", which
wasn't exported from skiboot. So we don't need this function and
it's safe to remove it.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PE#0 should be regarded as valid for P7IOC, while it's invalid for
PHB3. The patch adds flag EEH_VALID_PE_ZERO to differentiate those
two cases. Without the patch, we possibly see frozen PE#0 state is
cleared without EEH recovery taken on P7IOC as following kernel logs
indicate:
[root@ltcfbl8eb ~]# dmesg
:
pci 0000:00 : [PE# 000] Secondary bus 0 associated with PE#0
pci 0000:01 : [PE# 001] Secondary bus 1 associated with PE#1
pci 0001:00 : [PE# 000] Secondary bus 0 associated with PE#0
pci 0001:01 : [PE# 001] Secondary bus 1 associated with PE#1
pci 0002:00 : [PE# 000] Secondary bus 0 associated with PE#0
pci 0002:01 : [PE# 001] Secondary bus 1 associated with PE#1
pci 0003:00 : [PE# 000] Secondary bus 0 associated with PE#0
pci 0003:01 : [PE# 001] Secondary bus 1 associated with PE#1
pci 0003:20 : [PE# 002] Secondary bus 32..63 associated with PE#2
:
EEH: Clear non-existing PHB#3-PE#0
EEH: PHB location: U78AE.001.WZS00M9-P1-002
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When IOMMU bypass is enabled, a PCI device can read and write memory
that was not mapped by the driver without causing an EEH. That might
cause memory corruption, for example.
When we disable bypass, DMA reads and writes to addresses not mapped by
the IOMMU will cause an EEH, allowing us to debug such issues.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The current handling of EPOW_SHUTDOWN_ON_UPS event does not shutdown the
system after logging the message. All the events of EPOW_SYSTEM_SHUTDOWN
action code (EPOW_SHUTDOWN_ON_UPS is a part of it) must initiate system
shutdown as per the SPAPR spec. If the LPAR does not shutdown after
receiving this rtas based event, it will expose itself to a forced
abrupt shutdown initiated by the platform firmware. This patch fixes the
situation.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The M64 range information is missed in dmesg, which would be helpful in debug.
This patch prints the M64 range information in the same format as M32.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Turning snoops on is the last step in CAPP recovery. Sapphire is expected to
have reinitialized the PHB and done the previous recovery steps.
Add mode argument to opal call to do this. Driver can turn snoops off although
it does not currently.
Signed-off-by: Ryan Grimm <grimm@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add calls to the ps3_mm_set_repository_highmem() routine when the ps3
r1 highmem region is either created or destroyed.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add the new routine ps3_mm_set_repository_highmem() that saves highmem info to
the LV1 hypervisor registry so that the info will be available to second stage
OS's loaded by petitboot/kexec. FreeBSD and some Linux derivatives use
this feature.
Also, move the existing ps3_mm_get_repository_highmem() routine up in
the source file.
This implementation of ps3_mm_set_repository_highmem() assumes the repository
will have a single highmem region entry (at index 0).
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
To avoid the need for preprocessor conditionals in C source files add a set of
empty inline repository highmem write routines to platform.h that are used when
CONFIG_PS3_REPOSITORY_WRITE is not defined.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 2a2c74b2ef ("IBM Akebono: Add the Akebono platform") added a
select of IBM_EMAC_RGMII_WOL. But that Kconfig symbol isn't (yet) part
of the tree. So this select has been a nop since that commit was
included in v3.16-rc1.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Moving config DTL up so it is below config PPC_SPLPAR means that
menuconfig will show config DTL nicely indented right below config
PPC_SPLPAR when PPC_SPLPAR is enabled.
To contrast that, right now if I enable PPC_SPLPAR in menuconfig, all I
can immediately tell is that "something showed up further down the list
where I wasn't looking", and I end up having to toggle the option a few
times to figure out what showed up, or look at the KConfig to find out
that config DTL depends on config PPC_SPLPAR.
Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull second batch of powerpc updates from Michael Ellerman:
"The highlight is the series that reworks the idle management on
powernv, which allows us to use deeper idle states on those machines.
There's the fix from Anton for the "BUG at kernel/smpboot.c:134!"
problem.
An i2c driver for powernv. This is acked by Wolfram Sang, and he
asked that we take it through the powerpc tree.
A fix for audit from rgb at Red Hat, acked by Paul Moore who is one of
the audit maintainers.
A patch from Ben to export the symbol map of our OPAL firmware as a
sysfs file, so that tools can use it.
Also some CXL fixes, a couple of powerpc perf fixes, a fix for
smt-enabled, and the patch to add __force to get_user() so we can use
bitwise types"
* tag 'powerpc-3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
powerpc/powernv: Ignore smt-enabled on Power8 and later
powerpc/uaccess: Allow get_user() with bitwise types
powerpc/powernv: Expose OPAL firmware symbol map
powernv/powerpc: Add winkle support for offline cpus
powernv/cpuidle: Redesign idle states management
powerpc/powernv: Enable Offline CPUs to enter deep idle states
powerpc/powernv: Switch off MMU before entering nap/sleep/rvwinkle mode
i2c: Driver to expose PowerNV platform i2c busses
powerpc: add little endian flag to syscall_get_arch()
power/perf/hv-24x7: Use kmem_cache_free() instead of kfree
powerpc/perf/hv-24x7: Use per-cpu page buffer
cxl: Unmap MMIO regions when detaching a context
cxl: Add timeout to process element commands
cxl: Change contexts_lock to a mutex to fix sleep while atomic bug
powerpc: Secondary CPUs must set cpu_callin_map after setting active and online
Starting with POWER8, the subcore logic relies on all threads of a core
being booted so that they can participate in split mode switches. So on
those machines we ignore the smt_enabled_at_boot setting (smt-enabled on
the kernel command line).
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
[mpe: Update comment and change log to be more precise]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Newer versions of OPAL will provide this, so let's expose it to user
space so tools like perf can use it to properly decode samples in
firmware space.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Winkle is a deep idle state supported in power8 chips. A core enters
winkle when all the threads of the core enter winkle. In this state
power supply to the entire chiplet i.e core, private L2 and private L3
is turned off. As a result it gives higher powersavings compared to
sleep.
But entering winkle results in a total hypervisor state loss. Hence the
hypervisor context has to be preserved before entering winkle and
restored upon wake up.
Power-on Reset Engine (PORE) is a dedicated engine which is responsible
for powering on the chiplet during wake up. It can be programmed to
restore the register contests of a few specific registers. This patch
uses PORE to restore register state wherever possible and uses stack to
save and restore rest of the necessary registers.
With hypervisor state restore things fall under three categories-
per-core state, per-subcore state and per-thread state. To manage this,
extend the infrastructure introduced for sleep. Mainly we add a paca
variable subcore_sibling_mask. Using this and the core_idle_state we can
distingush first thread in core and subcore.
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Deep idle states like sleep and winkle are per core idle states. A core
enters these states only when all the threads enter either the
particular idle state or a deeper one. There are tasks like fastsleep
hardware bug workaround and hypervisor core state save which have to be
done only by the last thread of the core entering deep idle state and
similarly tasks like timebase resync, hypervisor core register restore
that have to be done only by the first thread waking up from these
state.
The current idle state management does not have a way to distinguish the
first/last thread of the core waking/entering idle states. Tasks like
timebase resync are done for all the threads. This is not only is
suboptimal, but can cause functionality issues when subcores and kvm is
involved.
This patch adds the necessary infrastructure to track idle states of
threads in a per-core structure. It uses this info to perform tasks like
fastsleep workaround and timebase resync only once per core.
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Originally-by: Preeti U. Murthy <preeti@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: linux-pm@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Alessio Igor Bogani
Gavin Shan
Michael Ellerman
Pranith Kumar
Cyril Bur
Emil Medve
Thadeu Lima de Souza Cascardo
Anshuman Khandual
Wei Yang
Ryan Grimm
Geoff Levand
Paul Bolle
Cody P Schafer
Linus Torvalds
Greg Kurz
Benjamin Herrenschmidt
Shreyas B. Prabhu