The memory for the private data is allocated using kzalloc in
alloc_etherdev (or alloc_netdev_mq respectively) so there is no need to
set the napi member to 0 explicitely.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver sometimes needs to know which function number the current
device is. This patch changes the code to use devfn over internal
register values.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5717 serdes phy brings link up via parallel detection without any
additional help from the driver. This patch changes the
tg3_setup_fiber_mii_phy() function to detect and allow the use of this
feature.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the code to make it legal to allocate only one MSI-X
vector. It also fixes a bug where the driver was not checking for error
return codes from pci_enable_msix().
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was incorrectly programming the indirection table such that
rx traffic intended for the second ring went to the first ring, rx
traffic intended for the third ring went to the second ring, etc. This
patch changes the code so that rx traffic is diverted to the proper
ring.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx resources for MSI-X interrupt vector 0 were not being freed
correctly. This happens because the teardown loop continue's to the
next loop iteration if it detects the tx ring for that vector is not
setup, thus bypassing the rx teardown code. This patch moves the
call to tg3_rx_prodring_free() earlier in the loop.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In certain edge conditions, internal tx resources can get corrupted.
This patch enables a bit that will fix the problem.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5717 and later devices relocate the APE mutex registers. This patch
organizes the code so that the driver can use the mutex registers in the
old and new locations.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some configurations need delay between the "write completed" indication
and new write to work reliably.
Realtek driver seems to use longer delay when polling the "write complete"
bit, so it waits long enough between writes with high probability (but
could probably break too). This patch adds a new udelay to make sure we
wait unconditionally some time after the write complete indication.
This caused a regression with XID 18000000 boards when the board specific
phy configuration writing many mdio registers was added in commit
2e955856ff (r8169: phy init for the 8169scd). Some of the configration
mdio writes would almost always fail, and depending on failure might leave
the PHY in non-working state.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Acked-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch compile tested only.
Convert legacy PM hooks to dev_pm_ops
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2: changed bonding module version, modified to apply on top of changes
from previous patch in series, and updated documentation to elaborate on
multiqueue awareness that now exists in bonding driver.
This patch give the user the ability to control the output slave for
round-robin and active-backup bonding. Similar functionality was
discussed in the past, but Jay Vosburgh indicated he would rather see a
feature like this added to existing modes rather than creating a
completely new mode. Jay's thoughts as well as Neil's input surrounding
some of the issues with the first implementation pushed us toward a
design that relied on the queue_mapping rather than skb marks.
Round-robin and active-backup modes were chosen as the first users of
this slave selection as they seemed like the most logical choices when
considering a multi-switch environment.
Round-robin mode works without any modification, but active-backup does
require inclusion of the first patch in this series and setting
the 'all_slaves_active' flag. This will allow reception of unicast traffic on
any of the backup interfaces.
This was tested with IPv4-based filters as well as VLAN-based filters
with good results.
More information as well as a configuration example is available in the
patch to Documentation/networking/bonding.txt.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2: changed parameter name from 'keep_all' to 'all_slaves_active' and
skipped setting slaves to inactive rather than creating a new flag at
Jay's suggestion.
In an effort to suppress duplicate frames on certain bonding modes
(specifically the modes that do not require additional configuration on
the switch or switches connected to the host), code was added in the
generic receive patch in 2.6.16. The current behavior works quite well
for most users, but there are some times it would be nice to restore old
functionality and allow all frames to make their way up the stack.
This patch adds support for a new module option and sysfs file called
'all_slaves_active' that will restore pre-2.6.16 functionality if the
user desires. The default value is '0' and retains existing behavior,
but the user can set it to '1' and allow all frames up if desired.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hi,
__pppoe_xmit() in drivers/net/pppoe always returns 1.
When the methods fails (via goto abort), it should return 0 and not 1.
Regards,
Rami Rosen
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicated #include('s) in drivers/net/wan/x25_asy.c
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix bug in multilink fragment size calculation introduced by
commit 9c705260fe
"ppp: ppp_mp_explode() redesign"
Signed-off-by: Ben McKeegan <ben@netservers.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is alternative to a previous patch submitted by Joe Perches.
Create common macros e_<level> and e_dev_<level> that use netdev_<level> and
dev_<level> similar to e1000e.
Redefined pr_fmt for driver messages.
Use %pM to display MAC address.
Aligned text to better match the new format.
CC: Joe Perches <joe@perches.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tobias Klauser
Matt Carlson
David S. Miller
Timo Teräs
Shirley Ma
Denis Kirjanov
Andy Gospodarek
Rami Rosen
Huang Weiyi
Ben McKeegan
John Fastabend
Anirban Chakraborty
Emil Tantilov
Jeff Kirsher