This makes sure the ethtool's set_settings() callback of network
drivers don't ignore the 16 most significant bits when ethtool calls
their set_settings().
All drivers compiled with make allyesconfig on x86_64 have been
updated.
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- use adequate MAC_VER id
(see 01dc7fec40)
- remove duplicate rtl_firmware_info record
- remove duplicate functions
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resolved logic conflicts causing a build failure due to
drivers/net/r8169.c changes using a patch from Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware is cached during the first successfull call to open() and
released once the network device is unregistered. The driver uses the
cached firmware between open() and unregister_netdev().
So far the firmware is optional : a failure to load the firmware does
not prevent open() to success. It is thus necessary to 1) unregister
all 816x / 810[23] devices and 2) force a driver probe to issue a new
firmware load.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Fixed-by: Ciprian Docan <docan@eden.rutgers.edu>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
- the MSS value is actually contained in a 11 bits wide (0x7ff) field.
The extra bit in the former MSSMask did encompass the TSO command
bit ("LargeSend") as well (0xfff). Oops.
- the Tx descriptor layout is not the same through the whole chipset
family. The 8169 documentation, the 8168c documentation and Realtek's
drivers (8.020.00, 1.019.00, 6.014.00) highlight two layouts:
1. 8169, 8168 up to 8168b (included) and 8101
2. {8102e, 8168c} and beyond
- notwithstanding the "first descriptor" and "last descriptor" bits, the
same Tx descriptor content is enforced when a packet consists of several
descriptors. The chipsets are documented to require it.
Credits go to David Dillow <dave@thedillows.org> for the original patch.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Realtek <nic_swsd@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple conversion with a bit of needed cleanup.
This also fixes:
- confusion around vlan_features in rtl8169_vlan_mode(),
- problem with broken TSO for too big MTU (the limit is set
at 0xFFF --- max MSS field value).
SG+IP_CSUM+TSO is left disabled by default, based on suggestion by
David Dillow.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new chip for RTL8105 whose settings are the same with RTL_GIGA_MAC_VER_30.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows "ethtool advertise" to control the speed and duplex
features the device offers the switch.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
For some time is known that ASPM is causing troubles on r8169, i.e. make
device randomly stop working without any errors in dmesg.
Currently Tomi Leppikangas reports that system with r8169 device hangs
with MCE errors when ASPM is enabled:
https://bugzilla.redhat.com/show_bug.cgi?id=642861#c4
Lets disable ASPM for r8169 devices at all, to avoid problems with
r8169 PCIe devices at least for some users.
Reported-by: Tomi Leppikangas <tomi.leppikangas@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- adjust code of rtl8169_set_speed_xmii function
- remove parts of code which are done in rtl_pll_power_up
function (8168 only)
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
- fix the RTL8111DP turn off the power when DASH is enabled.
- RTL_GIGA_MAC_VER_27 must wait for tx finish before reset.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Adjust and remove certain settings of RTL8102E which are for previous chips.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-off-by: Francois Romieu <romieu@fr.zoreil.com>
Without calling of netif_carrier_off at the end of the probe the operstate
is unknown when the device is initially opened. By default the carrier is
on so when the device is opened and netif_carrier_on is called the link
watch event is not fired and operstate remains zero (unknown).
This patch fixes this behavior in forcedeth and r8169.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the RxFIFO interruption is masked for most 8168, nothing prevents
it to appear in the irq status word. This is no excuse to crash.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Ivan Vecera <ivecera@redhat.com>
Cc: Hayes <hayeswang@realtek.com>
Some experiment-based action to prevent my 8168 chipsets locking-up hard
in the irq handler under load (pktgen ~1Mpps). Apparently a reset is not
always mandatory (is it at all ?).
- RTL_GIGA_MAC_VER_12
- RTL_GIGA_MAC_VER_25
Missed ~55% packets. Note:
- this is an old SiS 965L motherboard
- the 8168 chipset emits (lots of) control frames towards the sender
- RTL_GIGA_MAC_VER_26
The chipset does not go into a frenzy of mac control pause when it
crashes yet but it can still be crashed. It needs more work.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Ivan Vecera <ivecera@redhat.com>
Cc: Hayes <hayeswang@realtek.com>
I found that one of the 8168c chipsets (concretely XID 1c4000c0) starts
generating RxFIFO overflow errors. The result is an infinite loop in
interrupt handler as the RxFIFOOver is handled only for ...MAC_VER_11.
With the workaround everything goes fine.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes <hayeswang@realtek.com>
The firmware agent is not available during resume. Loading the firmware
during open() (see eee3a96c63) is not
enough.
close() is run during resume through rtl8169_reset_task(), whence the
mildly natural release of firmware in the driver removal method instead.
It will help with http://bugs.debian.org/609538. It will not avoid
the 60 seconds delay when:
- there is no firmware
- the driver is loaded and the device is not up before a suspend/resume
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Jarek Kamiński <jarek@vilo.eu.org>
Cc: Hayes <hayeswang@realtek.com>
Cc: Ben Hutchings <benh@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update rtl_phy_write_fw function. The new function could
parse the complex firmware which is used by RTL8111E and later.
The new firmware may read data and do some operations, not just
do writing only.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Decotigny
Francois Romieu
David S. Miller
Michał Mirosław
hayeswang
Eric Dumazet
Oliver Neukum
Stanislaw Gruszka
Ivan Vecera