Commit Graph

297 Commits

Author SHA1 Message Date
Alex Williamson 24a4742f0b PCI: Track the size of each saved capability data area
This will allow us to store and load it later.

Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-05-21 12:17:08 -07:00
Jesse Barnes 51c2e0a7e5 PCI: add latency tolerance reporting enable/disable support
Latency tolerance reporting allows devices to send messages to the root
complex indicating their latency tolerance for snooped & unsnooped
memory transactions.  Add support for enabling & disabling this
feature, along with a routine to set the max latencies a device should
send upstream.

Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-05-11 15:18:53 -07:00
Jesse Barnes 48a92a8179 PCI: add OBFF enable/disable support
OBFF (optimized buffer flush/fill), where supported, can help improve
energy efficiency by giving devices information about when interrupts
and other activity will have a reduced power impact.  It requires
support from both the device and system (i.e. not only does the device
need to respond to OBFF messages, but the platform must be capable of
generating and routing them to the end point).

Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-05-11 15:18:48 -07:00
Jesse Barnes b48d4425b6 PCI: add ID-based ordering enable/disable support
Add support to allow drivers to enable/disable ID-based ordering.  Where
supported, ID-based ordering can significantly improve the latency of
individual requests by preventing them from queueing up behind unrelated
traffic.

Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-05-11 15:18:40 -07:00
Rafael J. Wysocki 8b8bae901c PCI/ACPI: Report ASPM support to BIOS if not disabled from command line
We need to distinguish the situation in which ASPM support is
disabled from the command line or through .config from the situation
in which it is disabled, because the hardware or BIOS can't handle
it.  In the former case we should not report ASPM support to the BIOS
through ACPI _OSC, but in the latter case we should do that.

Introduce pcie_aspm_support_enabled() that can be used by
acpi_pci_root_add() to determine whether or not it should report ASPM
support to the BIOS through _OSC.

Cc: stable@kernel.org
References: https://bugzilla.kernel.org/show_bug.cgi?id=29722
References: https://bugzilla.kernel.org/show_bug.cgi?id=20232
Reported-and-tested-by: Ortwin Glück <odi@odi.ch>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-03-21 09:38:02 -07:00
Linus Torvalds 99759619b2 Merge branch 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  PCI: label: remove #include of ACPI header to avoid warnings
  PCI: label: Fix compilation error when CONFIG_ACPI is unset
  PCI: pre-allocate additional resources to devices only after successful allocation of essential resources.
  PCI: introduce reset_resource()
  PCI: data structure agnostic free list function
  PCI: refactor io size calculation code
  PCI: do not create quirk I/O regions below PCIBIOS_MIN_IO for ICH
  PCI hotplug: acpiphp: set current_state to D0 in register_slot
  PCI: Export ACPI _DSM provided firmware instance number and string name to sysfs
  PCI: add more checking to ICH region quirks
  PCI: aer-inject: Override PCIe AER Mask Registers
  PCI: fix tlan build when CONFIG_PCI is not enabled
  PCI: remove quirk for pre-production systems
  PCI: Avoid potential NULL pointer dereference in pci_scan_bridge
  PCI/lpc: irq and pci_ids patch for Intel DH89xxCC DeviceIDs
  PCI: sysfs: Fix failure path for addition of "vpd" attribute
2011-03-18 10:56:44 -07:00
Matt Carlson d4894f3ea7 tg3: Add code to verify RODATA checksum of VPD
This patch adds code to verify the checksum stored in the "RV" info
keyword of the RODATA VPD section.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-10 01:56:12 -08:00
Randy Dunlap 3449248c87 PCI: fix tlan build when CONFIG_PCI is not enabled
When CONFIG_PCI is not enabled, tlan.c has a build error:
drivers/net/tlan.c:503: error: implicit declaration of function 'pci_wake_from_d3'

so add an inline function stub for this function to pci.h when
PCI is not enabled, similar to other stubbed PCI functions.

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-02-16 11:46:09 -08:00
Markus Trippelsdorf ab0724ffee PCI / ACPI: Fix build issue in pci_root.c for !CONFIG_PCIEPORTBUS
The compilation of drivers/acpi/pci_root.c fails if
CONFIG_PCIEPORTBUS is unset.  Fix the problem.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-01-14 15:23:25 -08:00
Rafael J. Wysocki b6e335aeeb PCI/PM: Use pm_wakeup_event() directly for reporting wakeup events
After recent changes related to wakeup events pm_wakeup_event()
automatically checks if the given device is configured to signal wakeup,
so pci_wakeup_event() may be a static inline function calling
pm_wakeup_event() directly.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-01-14 08:55:43 -08:00
Rafael J. Wysocki 415e12b237 PCI/ACPI: Request _OSC control once for each root bridge (v3)
Move the evaluation of acpi_pci_osc_control_set() (to request control of
PCI Express native features) into acpi_pci_root_add() to avoid calling
it many times for the same root complex with the same arguments.
Additionally, check if all of the requisite _OSC support bits are set
before calling acpi_pci_osc_control_set() for a given root complex.

References: https://bugzilla.kernel.org/show_bug.cgi?id=20232
Reported-by: Ozan Caglayan <ozan@pardus.org.tr>
Tested-by: Ozan Caglayan <ozan@pardus.org.tr>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-01-14 08:55:41 -08:00
Jon Mason 1d3c16a818 PCI: make pci_restore_state return void
pci_restore_state only ever returns 0, thus there is no benefit in
having it return any value.  Also, a large majority of the callers do
not check the return code of pci_restore_state.  Make the
pci_restore_state a void return and avoid the overhead.

Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-12-23 12:53:09 -08:00
Matthew Garrett bf4d290869 PCI: Export some PCI PM functionality
It's helpful to have some extra PCI power management functions available to
platform code, so move the declarations to an exported header.

Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-10-17 20:03:06 -07:00
Stephen Hemminger 42b219322a PCI: pci_driver make name const
The name field in pci_driver should be const, it is not
modified by PCI subsystem.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-10-15 13:09:49 -07:00
Dave Airlie 92298e6683 PCI: provide stub pci_domain_nr function for !CONFIG_PCI configs
Allows the new PCI domain aware DRM code to compile on m68k.

Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-08-13 16:19:59 -07:00
Jacob Pan 253d2e5498 PCI: disable mmio during bar sizing
It is a known issue that mmio decoding shall be disabled while doing PCI
bar sizing. Host bridge and other devices (PCI PIC) shall be excluded for
certain platforms. This patch mainly comes from Mathew Willcox's
patch in http://kerneltrap.org/mailarchive/linux-kernel/2007/9/13/258969.

A new flag bit "mmio_alway_on" is added to pci_dev with the intention that
devices with their mmio decoding cannot be disabled during BAR sizing shall
have this bit set, preferrablly in their quirks.

Without this patch, Intel Moorestown platform graphics unit will be
corrupted during bar sizing activities.

Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-07-30 09:29:35 -07:00
Bjorn Helgaas 58c84eda07 PCI: fall back to original BIOS BAR addresses
If we fail to assign resources to a PCI BAR, this patch makes us try the
original address from BIOS rather than leaving it disabled.

Linux tries to make sure all PCI device BARs are inside the upstream
PCI host bridge or P2P bridge apertures, reassigning BARs if necessary.
Windows does similar reassignment.

Before this patch, if we could not move a BAR into an aperture, we left
the resource unassigned, i.e., at address zero.  Windows leaves such BARs
at the original BIOS addresses, and this patch makes Linux do the same.

This is a bit ugly because we disable the resource long before we try to
reassign it, so we have to keep track of the BIOS BAR address somewhere.
For lack of a better place, I put it in the struct pci_dev.

I think it would be cleaner to attempt the assignment immediately when the
claim fails, so we could easily remember the original address.  But we
currently claim motherboard resources in the middle, after attempting to
claim PCI resources and before assigning new PCI resources, and changing
that is a fairly big job.

Addresses https://bugzilla.kernel.org/show_bug.cgi?id=16263

Reported-by: Andrew <nitr0@seti.kr.ua>
Tested-by: Andrew <nitr0@seti.kr.ua>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-07-16 11:39:48 -07:00
Linus Torvalds 9a9620db07 Merge branch 'linux_next' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/i7core
* 'linux_next' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/i7core: (83 commits)
  i7core_edac: Better describe the supported devices
  Add support for Westmere to i7core_edac driver
  i7core_edac: don't free on success
  i7core_edac: Add support for X5670
  Always call i7core_[ur]dimm_check_mc_ecc_err
  i7core_edac: fix memory leak of i7core_dev
  EDAC: add __init to i7core_xeon_pci_fixup
  i7core_edac: Fix wrong device id for channel 1 devices
  i7core: add support for Lynnfield alternate address
  i7core_edac: Add initial support for Lynnfield
  i7core_edac: do not export static functions
  edac: fix i7core build
  edac: i7core_edac produces undefined behaviour on 32bit
  i7core_edac: Use a more generic approach for probing PCI devices
  i7core_edac: PCI device is called NONCORE, instead of NOCORE
  i7core_edac: Fix ringbuffer maxsize
  i7core_edac: First store, then increment
  i7core_edac: Better parse "any" addrmask
  i7core_edac: Use a lockless ringbuffer
  edac: Create an unique instance for each kobj
  ...
2010-06-04 15:39:54 -07:00
Linus Torvalds 9a90e09854 Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (27 commits)
  ACPI: Don't let acpi_pad needlessly mark TSC unstable
  drivers/acpi/sleep.h: Checkpatch cleanup
  ACPI: Minor cleanup eliminating redundant PMTIMER_TICKS to NS conversion
  ACPI: delete unused c-state promotion/demotion data strucutures
  ACPI: video: fix acpi_backlight=video
  ACPI: EC: Use kmemdup
  drivers/acpi: use kasprintf
  ACPI, APEI, EINJ injection parameters support
  Add x64 support to debugfs
  ACPI, APEI, Use ERST for persistent storage of MCE
  ACPI, APEI, Error Record Serialization Table (ERST) support
  ACPI, APEI, Generic Hardware Error Source memory error support
  ACPI, APEI, UEFI Common Platform Error Record (CPER) header
  Unified UUID/GUID definition
  ACPI Hardware Error Device (PNP0C33) support
  ACPI, APEI, PCIE AER, use general HEST table parsing in AER firmware_first setup
  ACPI, APEI, Document for APEI
  ACPI, APEI, EINJ support
  ACPI, APEI, HEST table parsing
  ACPI, APEI, APEI supporting infrastructure
  ...
2010-05-28 14:42:18 -07:00
Huang Ying affb72c3a8 ACPI, APEI, PCIE AER, use general HEST table parsing in AER firmware_first setup
Now, a dedicated HEST tabling parsing code is used for PCIE AER
firmware_first setup. It is rebased on general HEST tabling parsing
code of APEI. The firmware_first setup code is moved from PCI core to
AER driver too, because it is only AER related.

Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Len Brown <len.brown@intel.com>
2010-05-19 22:40:14 -04:00
Mauro Carvalho Chehab d1fd4fb69e i7core_edac: Add a code to probe Xeon 55xx bus
This code changes the detection procedure of i7core_edac. Instead of
directly probing for MC registers, it probes for another register found
on Nehalem. If found, it tries to pick the first MC PCI BUS. This should
work fine with Xeon 35xx, but, on Xeon 55xx, this is at bus 254 and 255
that are not properly detected by the non-legacy PCI methods.

The new detection code scans specifically at buses 254 and 255 for the
Xeon 55xx devices.

This code has not tested yet. After working, a change at the code will
be needed, since the i7core is not yet ready for working with 2 sets of
MC.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2010-05-10 11:44:51 -03:00
Yinghai dda5654927 intel-iommu: use physfn to search drhd for VF
When virtfn is used, we should use physfn to find correct drhd

-v2: add pci_physfn() Suggested by Roland Dreier <rdreier@cisco.com>
     do can remove ifdef in dmar.c
-v3: Chris pointed out we need that for dma_find_matched_atsr_unit too
     also change dmar_pci_device_match() static

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Roland Dreier <rdreier@cisco.com>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-04-09 17:00:00 +01:00
FUJITA Tomonori 5f3cd1e0bb dma-mapping: pci: move pci_set_dma_mask and pci_set_consistent_dma_mask to pci-dma-compat.h
We can use pci-dma-compat.h to implement pci_set_dma_mask and
pci_set_consistent_dma_mask as we do with the other PCI DMA API.

We can remove HAVE_ARCH_PCI_SET_DMA_MASK too.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Greg KH <greg@kroah.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-12 15:52:42 -08:00
FUJITA Tomonori f41b177157 pci-dma: add linux/pci-dma.h to linux/pci.h
All the architectures properly set NEED_DMA_MAP_STATE now so we can safely
add linux/pci-dma.h to linux/pci.h and remove the linux/pci-dma.h
inclusion in arch's asm/pci.h

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-12 15:52:42 -08:00
Linus Torvalds 322aafa664 Merge branch 'x86-mrst-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-mrst-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (30 commits)
  x86, mrst: Fix whitespace breakage in apb_timer.c
  x86, mrst: Fix APB timer per cpu clockevent
  x86, mrst: Remove X86_MRST dependency on PCI_IOAPIC
  x86, olpc: Use pci subarch init for OLPC
  x86, pci: Add arch_init to x86_init abstraction
  x86, mrst: Add Kconfig dependencies for Moorestown
  x86, pci: Exclude Moorestown PCI code if CONFIG_X86_MRST=n
  x86, numaq: Make CONFIG_X86_NUMAQ depend on CONFIG_PCI
  x86, pci: Add sanity check for PCI fixed bar probing
  x86, legacy_irq: Remove duplicate vector assigment
  x86, legacy_irq: Remove left over nr_legacy_irqs
  x86, mrst: Platform clock setup code
  x86, apbt: Moorestown APB system timer driver
  x86, mrst: Add vrtc platform data setup code
  x86, mrst: Add platform timer info parsing code
  x86, mrst: Fill in PCI functions in x86_init layer
  x86, mrst: Add dummy legacy pic to platform setup
  x86/PCI: Moorestown PCI support
  x86, ioapic: Add dummy ioapic functions
  x86, ioapic: Early enable ioapic for timer irq
  ...

Fixed up semantic conflict of new clocksources due to commit
17622339af ("clocksource: add argument to resume callback").
2010-03-07 15:59:39 -08:00