This allows a libsas driver to optionally provide a soft reset handler
for libata to drive. The isci driver allows software to control the
assertion/deassertion of SRST.
[jejb: checkpatch.pl fixes]
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Head off doomed-to-fail i/o in sas_queuecommand before sending it down
the ata path.
Before:
sd 7:0:0:0: [sdd] Synchronizing SCSI cache
ata8: no sense translation for status: 0x00
ata8: translated ATA stat/err 0x00/00 to SCSI SK/ASC/ASCQ 0xb/00/00
ata8.00: device reported invalid CHS sector 0
ata8: status=0x00 { }
ata8: no sense translation for status: 0x00
ata8: translated ATA stat/err 0x00/00 to SCSI SK/ASC/ASCQ 0xb/00/00
ata8.00: device reported invalid CHS sector 0
ata8: status=0x00 { }
ata8: no sense translation for status: 0x00
ata8: translated ATA stat/err 0x00/00 to SCSI SK/ASC/ASCQ 0xb/00/00
ata8.00: device reported invalid CHS sector 0
ata8: status=0x00 { }
sd 7:0:0:0: [sdd] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
sd 7:0:0:0: [sdd] Sense Key : Aborted Command [current] [descriptor]
sd 7:0:0:0: [sdd] Add. Sense: No additional sense information
sd 7:0:0:0: [sdd] Stopping disk
After:
sd 9:0:0:0: [sdd] Synchronizing SCSI cache
sd 9:0:0:0: [sdd] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
sd 9:0:0:0: [sdd] Stopping disk
sd 9:0:0:0: [sdd] START_STOP FAILED
sd 9:0:0:0: [sdd] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
This is a cosmetic change as sata i/o can still leak to a gone device,
but this addresses the nominal hotplug case when releasing the target.
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Commit 56dd2c06 "libsas: Don't issue commands to devices that have been
hot-removed" edited Darrick's original patch to remove setting 'gone' in
the sas_deform_port() path because that prevented scsi sync cache
commands from being issued when the driver was unloaded. However, this
allows true device gone notifications (as signaled port phy events) to
trigger sync cache commands to devices that are known to be unreachable.
Teach libsas which sas_deform_port() invocations are likely device gone
events.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Commit 1292500b replaced
"=m" (*field) : "1" (*field)
with
"=m" (*field) :
with comment "The following patch fixes it by using the '+' operator on
the (*field) operand, marking it as read-write to gcc."
'+' was actually forgotten. This really puts it.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <jbottomley@parallels.com>
drivers/scsi/osst.c: In function '__os_scsi_tape_open':
drivers/scsi/osst.c:4705: warning: ISO C90 forbids mixed declarations and code
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Index i was already used in the outer loop. Fixes a potentially-infinite
loop.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Willem Riede <osst@riede.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
In error recovery, most scsi error recovery stages will send a TUR command
for every bad command when a driver's error handler reports success. When
several bad commands to the same device, this results in a device
being probed multiple times.
This becomes very problematic if the device or connection is in a state
where the device still doesn't respond to commands even after a recovery
function returns success. The error handler must wait for the test
commands to time out. The time waiting for the redundant commands can
drastically lengthen error recovery.
This patch alters the scsi mid-layer's error routines to send test commands
once per device instead of once per bad command. This can drastically
lower error recovery time.
[jejb: fixed up whitespace and formatting]
Signed-of-by: David Jeffery <djeffery@redhat.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Some kernel transport drivers unconditionally disable
retrieval of the Caching mode page. One such for example is
the BBB/CBI transport over USB. Such a restraint is too
harsh as some devices do support the Caching mode
page. Unconditionally enabling the retrieval of this mode
page over those transports at their transport code level may
result in some devices failing and becoming unusable.
This patch implements a method of retrieving the Caching
mode page without unconditionally enabling it in the
transports which unconditionally disable it. The idea is to
ask for all supported pages, page code 0x3F, and then search
for the Caching mode page in the mode parameter data
returned. The sd driver already asks for all the mode pages
supported by the attached device by setting the page code to
0x3F in order to find out if the media is write protected by
reading the WP bit in the Device Specific Parameter
field. It then attempts to retrieve only the Caching mode
page by setting the page code to 8 and actually attempting
to retrieve it if and only if the transport allows it.
The method implemented here is that if the transport doesn't
allow retrieval of the Caching mode page and the device is
not RBC, then we ask for all pages supported by setting the
page code to 0x3F (similarly to how the WP bit is retrieved
above), and then we search for the Caching mode page in the
mode parameter data returned.
With this patch, devices over SATA, report this (no change):
Oct 22 18:45:58 localhost kernel: sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
Oct 22 18:45:58 localhost kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0
Oct 22 18:45:58 localhost kernel: sd 0:0:0:0: [sda] Write Protect is off
Oct 22 18:45:58 localhost kernel: sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
Oct 22 18:45:58 localhost kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Smart devices report their Caching mode page. This is a
change where we'd previously see the kernel making
assumption about the device's cache being write-through:
Oct 22 18:45:58 localhost kernel: sd 6:0:0:0: Attached scsi generic sg2 type 0
Oct 22 18:45:58 localhost kernel: sd 6:0:0:0: [sdb] 610472646 4096-byte logical blocks: (2.50 TB/2.27 TiB)
Oct 22 18:45:58 localhost kernel: sd 6:0:0:0: [sdb] Write Protect is off
Oct 22 18:45:58 localhost kernel: sd 6:0:0:0: [sdb] Mode Sense: 47 00 10 08
Oct 22 18:45:58 localhost kernel: sd 6:0:0:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA
And "dumb" devices over BBB, are correctly shown not to
support reporting the Caching mode page:
Oct 22 18:49:06 localhost kernel: sd 7:0:0:0: [sdc] 15663104 512-byte logical blocks: (8.01 GB/7.46 GiB)
Oct 22 18:49:06 localhost kernel: sd 7:0:0:0: [sdc] Write Protect is off
Oct 22 18:49:06 localhost kernel: sd 7:0:0:0: [sdc] Mode Sense: 23 00 00 00
Oct 22 18:49:06 localhost kernel: sd 7:0:0:0: [sdc] No Caching mode page present
Oct 22 18:49:06 localhost kernel: sd 7:0:0:0: [sdc] Assuming drive cache: write through
Version 2 adds this:
Some devices don't support page code 0x3F, and others require a
fixed transfer length of 192 bytes. This single commit includes a
patch by Alan Stern which fixes this.
Reported-and-tested-by: Richard Senior <richard@r-senior.demon.co.uk>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Luben Tuikov <ltuikov@yahoo.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Modified the event coalescing code for iSCSI offload to combat both
corner cases and optimize performance as follows:
1. Added mechanism to loop back a second time to process any leftover
CQEs that was generated by the hardware during the time the driver is
busy processing previous CQEs in the bh. This not only helps the
performance but also fixes the corner case when no more CQEs are being
generated in the pipeline; so those leftover CQEs will get a a chance
to be processed.
2. Added ARM_CQE_FP to distinguish between fast path arming versus
slow path arming. This change will guarantee that the CQEs will
always get a chance to be re-armed during fast path completions.
3. Removed the inline event coalescing division for perf optimization.
Also fixed a division-by-zero error when the event_coal_div module
param was set to 0.
4. Changed the default SQ WQEs size from 256 to 128 to match chip
default.
5. Changed the cmd_per_lun from 32 to 24.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Modified the 10s wait time for inflight offload connections to
advance to the next state to 2s based on test result.
Modified the 20s shutdown timeout to 30s based on test result.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <jbottomley@parallels.com>
The number of chip's internal command cell, which is use to generate
SCSI cmd packets to the target, was not initialized correctly by
the driver when the sq_size is changed from the default 128.
This, in turn, will create a problem where the chip's transmit pipe
will erroneously reuse an old command cell that is no longer valid.
The fix is to correctly initialize the chip's command cell upon setup.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Since queue_work does not requeue, there is no need to check
if a work is in progress using the AF_DPC_SCHEDULED flag.
queue_work would return if work is pending without adding the
work, do_dpc would again get invoked from qla4xxx_timer if
there is still DPC flags set.
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Do not process interrupt unconditionally during mailbox processing which can
lead to spurious interrupt. Mailbox completion are now polled if interrupt are
disabled or wait for interrupt to come in if its enabled
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Complete the cmd if sense length is zero. For cases where sense
data spans across multiple iocb's by FW, we need to hold on to the
I/O (ha->status_srb != NULL) till we have processed them all and
copied the sense data from internal buffer to scsi_cmd sense buffer.
Signed-off-by: Prasanna Mumbai <prasanna.mumbai@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
The block layer discard alignment is reported in bytes, not in units of
the logical block size.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Dave Jiang
Dan Williams
Samuel Thibault
Andrew Morton
Roel Kluin
Vasiliy Kulikov
David Jeffery
Luben Tuikov
Eddie Wai
Vikas Chaudhary
Harish Zunjarrao
Lalit Chandivade
Prasanna Mumbai
Martin K. Petersen