This patch (as1597) fixes some of the error paths in usbhid's suspend
routine. The driver was not careful to restart everything that might
have been stopped, in cases where a suspend failed.
For example, once the HID_SUSPENDED flag is set, an output report
submission would not restart the corresponding URB queue. If a
suspend fails, it's therefore necessary to check whether the queues
need to be restarted.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch (as1596) improves the queue-restart logic in usbhid by
checking to see if the device is suspended or a reset is about to
occur. There's no point submitting an URB if either of those is
true.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch (as1595) improves the usbhid driver by using the
HID_SUSPENDED bitflag to indicate that the device is suspended rather
than using HID_REPORTED_IDLE, which the patch removes.
Since HID_SUSPENDED was not being used for anything, and since the
name "HID_REPORTED_IDLE" doesn't convey much meaning, the end result
is easier to read and understand.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch (as1594) simplifies the usbhid driver by inlining a couple
of routines. As a result of an earlier patch, irq_out_pump_restart()
and ctrl_pump_restart() are each used in only one place. Since they
don't really do what their names say, and since they each involve only
about two lines of actual code, there's no reason to keep them as
separate functions.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch (as1593) fixes some logic errors in the usbhid driver
relating to runtime PM. The driver does not balance its calls to
usb_autopm_get_interface_async() and usb_autopm_put_interface_async().
For example, when the control queue is restarted the driver does a
_get. But the resume won't happen immediately, so the driver leaves
the queue stopped. When the resume does occur, the queue is restarted
and a second _get occurs, with no balancing _put.
The patch fixes the problem by rearranging the logic for restarting
the queues. All the _get/_put calls and bitflag settings in
__usbhid_submit_report() are moved into the queue-restart routines. A
balancing _put call is added for the case where the queue is still
suspended. A call to irq_out_pump_restart(), which doesn't take all
the right actions for restarting the irq-OUT queue, is replaced by a
call to usbhid_restart_out_queue(), which does. Similarly for
ctrl_pump_restart().
Finally, new code is added to prevent an autosuspend from happening
every time an URB is cancelled, and the comments explaining what
happens when an URB needs to be cancelled are expanded and clarified.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch (as1592) fixes an obscure problem in the usbhid driver.
Under some circumstances, a control or interrupt-OUT URB can be
submitted twice. This will happen if the first submission fails; the
queue pointers aren't updated, so the next time the queue is restarted
the same URB will be submitted again.
The problem is that raw_report gets deallocated during the first
submission. The second submission will then dereference and try to
free an already-freed region of memory. The patch fixes the problem
by setting raw_report to NULL when it is deallocated and checking for
NULL before dereferencing it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Sennheiser BTD500USB composit device requires the
HID_QUIRK_NOGET flag to be set for working proper. Without the
flag the device crashes during hid intialization.
Signed-off-by: Frank Kunz <xxxxxmichl@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The generic HID driver is obviously not a special driver, so move it
outside of the special drivers menu. Explain the usage and make the
default follow the HID setting. This should simplify migration from
older kernels. While at it, remove the redundant HID_SUPPORT option
and modify the HID and USB_HID entries to better explain the bus
structure.
Reported-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID subsystem updates from Jiri Kosina:
"Apart from various driver updates and added support for a number of
new devices (mostly multitouch ones, but not limited to), there is one
change that is worth pointing out explicitly: creation of HID device
groups and proper autoloading of hid-multitouch, implemented by Henrik
Rydberg."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (50 commits)
HID: wacom: fix build breakage without CONFIG_LEDS_CLASS
HID: waltop: Extend barrel button fix
HID: hyperv: Set the hid drvdata correctly
HID: wacom: Unify speed setting
HID: wacom: Add speed setting for Intuos4 WL
HID: wacom: Move Graphire raport header check.
HID: uclogic: Add support for UC-Logic TWHL850
HID: explain the signed/unsigned handling in hid_add_field()
HID: handle logical min/max signedness properly in parser
HID: logitech: read all 32 bits of report type bitfield
HID: wacom: Add LED selector control for Wacom Intuos4 WL
HID: hid-multitouch: fix wrong protocol detection
HID: wiimote: Fix IR data parser
HID: wacom: Add tilt reporting for Intuos4 WL
HID: multitouch: MT interface matching for Baanto
HID: hid-multitouch: Only match MT interfaces
HID: Create a common generic driver
HID: hid-multitouch: Switch to device groups
HID: Create a generic device group
HID: Allow bus wildcard matching
...
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some HCDs usb_unlink_urb() can directly call the
completion handler. That limits the spinlocks that can
be taken in the handler to locks not held while calling
usb_unlink_urb()
To prevent a race with resubmission, this patch exposes
usbcore's infrastructure for blocking submission, uses it
and so drops the lock without causing a race in usbhid.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the hid drivers of the bus drivers to a common generic hid
driver, and make it a proper module. This ought to simplify device
handling moving forward.
Cc: Gustavo Padovan <gustavo@padovan.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Devices that do not have a special driver are handled by the generic
driver. This patch does the same thing using device groups; Instead of
forcing a particular driver, the appropriate driver is picked up by
udev. As a consequence, one can now move a device from generic to
specific handling by a simple rebind. By adding a new device id to the
generic driver, the same thing can be done in reverse.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Acked-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Everytime a HID device is opened, a new hiddev_list is allocated with
kzalloc. This requires 64KB of physically contiguous memory, which could
easily push a heavily loaded system over the edge.
Allocating the same amount of memory with vmalloc shouldn't be nearly as
demanding, so let's do that instead. The memory isn't used for DMA and
doesn't look particularly performance sensitive, so this should be safe.
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
CC: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a USB device reset occurs, usbcore will refetch the device and configuration
descriptors and compare them with those retrieved before the reset to ensure
that they have not changed. For USB HID devices, this implicitly includes the
HID class descriptor (as this is fetched with the configuration descriptor).
However, the HID report descriptor is not checked again.
Whilst a change in the size of the HID report descriptor will be detected (as
this is held in the class descriptor), content changes to the report descriptor
which do not result in a change in its size will be missed. If a firmware update
were applied to a USB HID device which resulted in such a change to the report
descriptor after device reset, then this would not be picked up by usbhid.
This patch fixes this issue by allowing usbhid to check the contents of the
report descriptor after the device reset, and trigger a rebind of the device
if there is a mismatch.
Reviewed-by: Toby Gray <toby.gray@realvnc.com>
Signed-off-by: Simon Haggett <simon.haggett@realvnc.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In case IO cannot be started because there is a lack of bandwidth
on the bus, it makes no sense to reset the device. If IO is requested
because the device is opened, user space should be notified with
an error right away. If the lack of bandwidth arises later, for
example after resume, there's no other choice but to retry in the
hope that bandwidth will be freed.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for Waltop Sirius Battery Free Tablet. VisTablet Muse and Princeton
PTB-S1BK are other possible names of this tablet.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some quanta devices do not like to be polled for reports
descriptors, thus this quirk.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch (as1531) adds a NOGET quirk for the Slim+ keyboard marketed
by AIREN. This keyboard seems to have a lot of bugs; NOGET works
around only one of them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: okias <d.okias@gmail.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Alan Stern
Frank Kunz
Henrik Rydberg
Linus Torvalds
Jiri Kosina
Greg Kroah-Hartman
Oliver Neukum
Havard Skinnemoen
Simon Haggett
Oliver Neukum
Nikolai Kondrashov
Benjamin Tissoires