NCQ feature is unsupported on hisilicon sata controller, so disable
it. This version of IP is used by hip04 and hix5hd2 soc.
tj: "|=" was replaced with "=" for no reason. Restored "|=".
Signed-off-by: Kefeng Wang <kefeng.wang@linaro.org>
Sigend-off-by: Tejun Heo <tj@kernel.org>
Doing suspend/resume on imx6q and imx53 boards with no SATA disk
attached will trigger the following warning.
------------[ cut here ]------------
WARNING: CPU: 0 PID: 661 at drivers/ata/libahci.c:224 ahci_enable_ahci+0x74/0x8)
Modules linked in:
CPU: 0 PID: 661 Comm: sh Tainted: G W 3.15.0-rc5-next-20140521-000027
Backtrace:
[<80011c90>] (dump_backtrace) from [<80011e2c>] (show_stack+0x18/0x1c)
r6:803a22f4 r5:00000000 r4:00000000 r3:00000000
[<80011e14>] (show_stack) from [<80661e60>] (dump_stack+0x88/0xa4)
[<80661dd8>] (dump_stack) from [<80028fdc>] (warn_slowpath_common+0x70/0x94)
r5:00000009 r4:00000000
[<80028f6c>] (warn_slowpath_common) from [<80029024>] (warn_slowpath_null+0x24/)
r8:808f68c4 r7:00000000 r6:00000000 r5:00000000 r4:e0810004
[<80029000>] (warn_slowpath_null) from [<803a22f4>] (ahci_enable_ahci+0x74/0x80)
[<803a2280>] (ahci_enable_ahci) from [<803a2324>] (ahci_reset_controller+0x24/0)
r8:ddcd9410 r7:80351178 r6:ddcd9444 r5:dde8b850 r4:e0810000 r3:ddf35e90
[<803a2300>] (ahci_reset_controller) from [<803a2c68>] (ahci_platform_resume_ho)
r7:80351178 r6:ddcd9444 r5:dde8b850 r4:ddcd9410
[<803a2c30>] (ahci_platform_resume_host) from [<803a38f0>] (imx_ahci_resume+0x2)
r5:00000000 r4:ddcd9410
[<803a38c4>] (imx_ahci_resume) from [<803511ac>] (platform_pm_resume+0x34/0x54)
....
The reason is that the SATA controller has no working clock at this
point, and thus ahci_enable_ahci() fails to enable the controller. In
case that there is no SATA disk attached, the imx_sata_disable() gets
called in ahci_imx_error_handler(), and both sata_clk and sata_ref_clk
will be disabled there. Because all the imx_sata_enable() calls
afterward will return immediately due to imxpriv->no_device check, the
SATA controller working clock sata_clk will never get any chance to be
enabled again.
This is a regression caused by commit 90870d79d4 (ahci-imx: Port to
library-ised ahci_platform). Before the commit, only sata_ref_clk is
managed by the driver in enable/disable function. But after the commit,
all the clocks are enabled/disabled in a row by ahci platform helpers
ahci_platform_enable[disable]_clks. Since ahb_clk is a bus clock which
does not have gate at all, and i.MX low-power hardware module already
manages sata_clk across suspend/resume cycle, the only clock that needs
to be managed by software is sata_ref_clk.
So instead of using ahci_platform_enable[disable]_clks to manage all
the clocks in a row from imx_sata_enable[disable], we should manage
only sata_ref_clk in there.
Reported-by: Fabio Estevam <fabio.estevam@freescale.com>
Fixes: 90870d79d4 (ahci-imx: Port to library-ised ahci_platform)
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The current platform AHCI driver does not set the dma_mask correctly
for 64-bit DMA capable AHCI controller. This patch checks the AHCI
capability bit and set the dma_mask and coherent_dma_mask accordingly.
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
ahci_platform_get_resources handles resource management for
platform AHCI drivers, including getting a possible PHY
from the device tree. Since not all drivers need a PHY, it
ignores -ENODEV and -ENOSYS from devm_get_phy. However, when
the PHY subsystem is mistakenly disabled, -ENOSYS can be
returned even when a PHY is needed.
This patch modifies the -ENOSYS case to check if a "phys"
device tree node exists. If it exists, then clearly the PHY
subsystem is mistakenly disabled and the driver cannot work,
ahci_platform_get_resources will fail and propagate the error.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Use the zeroing function instead of dma_alloc_coherent & memset(,0,)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata updates from Tejun Heo:
"Nothing too interesting - another ahci platform driver variant,
additional controller support, minor fixes and cleanups"
* 'for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: Add Device ID for HighPoint RocketRaid 642L
ata: ep93xx: use dmaengine_prep_slave_sg api instead of internal callback
ahci: add PCI ID for Marvell 88SE91A0 SATA Controller
sata_fsl: remove check for CONFIG_MPC8315_DS
ahci: add support for Hisilicon sata
libahci_platform: add host_flags parameter in ahci_platform_init_host()
ata: ahci: append new hflag AHCI_HFLAG_NO_FBS
ata: use CONFIG_PM_SLEEP instead of CONFIG_PM where applicable in host drivers
ata: ahci_mvebu: new driver for Marvell Armada 380 AHCI interfaces
Documentation: dt-bindings: reformat and order list of ahci-platform compatibles
libata-sff: remove dead code
ata: SATL compliance for Inquiry Product Revision
pata_octeon_cf: use devm_kzalloc() to allocate cf_port
it is better to use generic api instead of calling an internal callback
like channel->device->device_prep_slave_sg().
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
A check for CONFIG_MPC8315_DS was added in v2.6.24. But the related
Kconfig symbol was never added to the tree. So the code behind this
check has effectively been dead for over six years. Remove it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata fixes from Tejun Heo:
"Mostly device-specific fixes. The only thing which isn't is the fix
for zpodd oops-on-detach bug"
* 'for-3.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: imx: PLL clock needs 100us to settle down
ata: pata_at91 only works on sam9
libata: clean up ZPODD when a port is detached
ahci: imx: software workaround for phy reset issue in resume
ahci: imx: add namespace for register enums
ahci: disable DEVSLP for Intel Valleyview
The commit e783c51 (ahci: imx: software workaround for phy reset issue
in resume) calls imx_sata_phy_reset() to reset phy immediately after
SATA MPLL is enabled. It seems working fine mostly, but fails in some
case as below.
...
ahci-imx 2200000.sata: failed to reset phy: -110
ahci-imx: probe of 2200000.sata failed with error -110
After talking to the designer, we learnt that when enabling i.MX6Q SATA
MPLL, we need to wait 100us for it to settle down for safety. Add this
required delay to fix above failure.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The hip04 SoC of hisilicon has an AHCI compliant SATA controller,
and it is compliant with the ahci 1.3 and sata 3.0 specification.
There is a wrong bit in HOST_CAP of hip04 sata controller, which
enable unsupported feature of FBS, use AHCI_HFLAG_NO_FBS hflag to
disable it.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kefeng Wang <kefeng.wang@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add a dynamic host_flags argument to make ahci_platform_init_host more flexible,
then remove the AHCI_HFLAGS(...) argument from some driver's ata_port_info,
and pass that in as the new argument.
Cc: Hans de Geode <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kefeng Wang <kefeng.wang@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch fixes host drivers to use CONFIG_PM_SLEEP instead of CONFIG_PM
where applicable. Benefits of this change:
* unused code is not being compiled in for CONFIG_PM=y, CONFIG_PM_SLEEP=n
and CONFIG_PM_RUNTIME=y configurations
* easier transition to use struct dev_pm_ops and SIMPLE_DEV_PM_OPS() in
the future
* more consistent code (there are host drivers which are using the correct
CONFIG_PM_SLEEP checks already)
The patch leaves the core libata code and ->port_[suspend,resume] support
in sata_[inic162x,nv,sil24].c alone for now.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The smc driver used by pata_at91 is at91sam9 specific, so building
this driver on another at91 platform results in this error:
ERROR: "sam9_smc_configure" [drivers/ata/pata_at91.ko] undefined!
ERROR: "sam9_smc_write_mode" [drivers/ata/pata_at91.ko] undefined!
ERROR: "sam9_smc_read_mode" [drivers/ata/pata_at91.ko] undefined!
This patch changes the Kconfig dependency to ensure it always works.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: linux-ide@vger.kernel.org
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
When a ZPODD device is unbound via sysfs, the ACPI notify handler
is not removed. This causes panics as observed in Bug #74601. The
panic only happens when the wake happens from outside the kernel
(i.e. inserting a media or pressing a button). Add a loop to
ata_port_detach which loops through the port's devices and checks
if zpodd is enabled, if so call zpodd_exit.
Cc: stable@vger.kernel.org
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Levente Kurusa <levex@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The Marvell Armada 380 SoC includes two AHCI compatible
interfaces. However, like all DMA-capable Marvell interface, they
require special handling to configure MBus windows. Therefore, this
commit adds a new ahci_mvebu driver, which relies on the
libahci_platform.c code recently introduced.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
When suspending imx6q systems which have rootfs on SATA, the following
error will likely be seen in resume. The SATA link will fail to come
up, and it results in an unusable system across the suspend/resume
cycle.
$ echo mem > /sys/power/state
PM: Syncing filesystems ... done.
PM: Preparing system for mem sleep
Freezing user space processes ... (elapsed 0.002 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.002 seconds) done.
PM: Entering mem sleep
sd 0:0:0:0: [sda] Synchronizing SCSI cache
sd 0:0:0:0: [sda] Stopping disk
PM: suspend of devices complete after 61.914 msecs
PM: suspend devices took 0.070 seconds
PM: late suspend of devices complete after 4.906 msecs
PM: noirq suspend of devices complete after 4.521 msecs
Disabling non-boot CPUs ...
CPU1: shutdown
CPU2: shutdown
CPU3: shutdown
Enabling non-boot CPUs ...
CPU1: Booted secondary processor
CPU1 is up
CPU2: Booted secondary processor
CPU2 is up
CPU3: Booted secondary processor
CPU3 is up
PM: noirq resume of devices complete after 10.486 msecs
PM: early resume of devices complete after 4.679 msecs
sd 0:0:0:0: [sda] Starting disk
PM: resume of devices complete after 22.674 msecs
PM: resume devices took 0.030 seconds
PM: Finishing wakeup.
Restarting tasks ... done.
$ ata1: SATA link down (SStatus 1 SControl 300)
ata1: SATA link down (SStatus 1 SControl 300)
ata1: limiting SATA link speed to 1.5 Gbps
ata1: SATA link down (SStatus 1 SControl 310)
ata1.00: disabled
ata1: exception Emask 0x10 SAct 0x0 SErr 0x4040000 action 0xe frozen t4
ata1: irq_stat 0x00000040, connection status changed
ata1: SError: { CommWake DevExch }
ata1: hard resetting link
sd 0:0:0:0: rejecting I/O to offline device
sd 0:0:0:0: killing request
sd 0:0:0:0: rejecting I/O to offline device
Aborting journal on device sda2-8.
sd 0:0:0:0: rejecting I/O to offline device
EXT4-fs warning (device sda2): ext4_end_bio:317: I/O error writing to inode 132577 (offset 0 size 0 starting block 26235)
Buffer I/O error on device sda2, logical block 10169
...
It's caused by a silicon issue that SATA phy does not get reset by
controller when coming back from LPM. The patch adds a software
workaround for this issue. It enforces a software reset on SATA phy
in imx_sata_enable() function, so that we can ensure SATA link will
come up properly in both power-on and resume.
The software reset is implemented by writing phy reset register through
the phy control register bus interface. Functions
imx_phy_reg_[addressing|write|read]() implement this bus interface, while
imx_sata_phy_reset() performs the actually reset operation.
Signed-off-by: Richard Zhu <r65037@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Update register enums a little bit to add proper namespace prefix, and
have the names match i.MX reference manual.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Ever since v2.6.19 the code contains a check for CONFIG_NO_ATA_LEGACY.
But that macro has never been defined. Apparently no one ran into
problems on platforms that do not support compatibility mode. So remove
this code that has been dead for over seven years.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Tejun Heo <tj@kernel.org>
The SCSI-to-ATA Translation standard says to use data words 25 and 26
unless they are spaces. For devices that use these words in the firmware
field, they are generally more useful anyway.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Kefeng Wang
Shawn Guo
Suravee Suthikulpanit
Mikko Perttunen
Joe Perches
Linus Torvalds
Jérôme Carretero
Martin K. Petersen
Barry Song
Andreas Schrägle
Paul Bolle
Bartlomiej Zolnierkiewicz
Arnd Bergmann
Levente Kurusa
Thomas Petazzoni
Keith Busch