Patch from Sascha Hauer
Current implementation of imx_gpio_mode does not allow to
configure all alternate routing possibilities of the i.MX. With
this patch every bit in the gpio setup registers has a
corresponding bit in the gpio_mode parameter, so every routing
should be possible now.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Sascha Hauer
After coming out of idle mode the h720x goes into slow mode. Switch
it back to run mode.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Daniel Jacobowitz
Thread flags are inherited on fork(). In order for a binary which has
the iWMMXt coprocessor enabled to run a binary which needs the FPA
emulation, we need to explicitly clear TIF_USING_IWMMXT if we are not
going to set it.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The VA addresses of the Anubis CPLD registers
confoict with the addresses for the ISA space
maps used by the rest of the s3c2410 architecture
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The `make buildcheck` is erroneously reporting that the .arch.info
list is referencing items in the .init section as it is not itself
postfixed with .init
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The `make buildcheck` is erroneously reporting that the earlyparam
list is referencing items in the .init section as it is not itself
postfixed with .init
Also, as per rmk's suggestion, rename the __early_param to
.early_param to bring it into line with everything else
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The `make buildcheck` is erroneously reporting that the taglist
is referencing items in the .init section as it is not itself
postfixed with .init
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The recently added futex.h contains an unused variable, which gcc
naturally warns about. Remove this unused variable.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Thomas Gleixner reported that mmaping and unmapping each physical
page in turn eventually caused the kernel to oops. It appears
that pfn_valid() in the discontigmem case was too simplistic for
proper operation.
Tighten the logic so we also check if the PFN is within the range
of the selected memory node.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
This patch cleans up the PXA Poodle platform code removing an unneeded
static iomap. It also corrects errors in the platform header file and
adds a missing GPIO define.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
The intel docs call it IXP2000_PRODUCT_ID, and we have a definition
for IXP2000_PRODUCT_ID as well, so IXP2000_PROD_ID can go. It's only
used in one place.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
This patch:
- changes the ixp2000_reg_write accessor to take a 'volatile void *'
instead of a 'volatile unsigned long *', which then allows passing in
a u32 * as first argument without being greeted with a warning; and
- adds an ixp2000_reg_read accessor.
We can then use these accessors in ixp2000 code to access on-chip
peripherals, instead of directly dereferencing pointers. This is for
use by the ixp2000 microengine driver which was recently announced on
netdev. We can't use readl/writel on the ixp2000 since it is usually
run in big-endian mode, and on big-endian platforms, readl/writel
perform byteswapping.
A future patch will remove the readback from ixp2000_reg_write, since
it's not needed to prevent erratum #66, and add manual readbacks to the
places that need them (writes are not synchronous since we map in device
space using XCB=101 nowadays), such as interrupt disabling and GPIO
manipulation. See also:
http://lists.arm.linux.org.uk/pipermail/linux-arm-kernel/2005-February/027084.html
Patch has been ACKed by Jeff Garzik.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As written in Documentation/feature-removal-schedule.txt, remove the
io_remap_page_range() kernel API.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the platform support code for two new Sharp Zaurus Models, Spitz
(SL-C3000) and Borzoi (SL-C3100).
This patch also adds most of the foundations for Akita (SL-C1000) Support.
The missing link for Akita is the driver for its I2C io expander. Once this
has been finished, the missing Kconfig option and machine declaration can
easily be added to this code.
Signed-Off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Separate out the Sharp Zaurus c7x0 series specific code from the Corgi
backlight driver. Abstract model/machine specific functions to corgi_lcd.c
via sharpsl.h
This enables the driver to be used by the Zaurus cxx00 series.
Signed-Off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The same LCD is present on both the Sharp Zaurus c7x0 series and the cxx00 but
with different framebuffer drivers (w100fb vs. pxafb). This patch adds
support for the cxx00 series to the LCD driver. It also adds some LCD to
touchscreen interface logic needed by the touchscreen driver to prevent
interference problems, the idea being to keep all the ugly code in one place
leaving the drivers themselves clean. sharpsl.h is used to provide the
abstraction.
Signed-Off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sharp's newer range of Zaurus clamshell handhelds, the cxx00's are similar to
the c7x0 series yet different. This patch series abstracts the differences
and generates a set of common drivers that support both series of devices. It
then adds machine support for Spitz (SL-C3000) and Borzoi (SL-C3100). Hooks
for Akita (SL-C1000) differences are also added. The I2C driver for its IO
expander is the only missing piece.
This patch:
Separate out the Sharp Zaurus c7x0 series specific code from corgi_ssp.c so
that other models such as the cxx00's can share it. Create sharpsl.h which
will be used to abstract machine/model specifics.
This enables the driver to be used by the Zaurus cxx00 series.
Signed-Off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sascha Hauer
Linus Torvalds
Daniel Jacobowitz
Al Viro
Russell King
Ben Dooks
Richard Purdie
Lennert Buytenhek
Randy Dunlap