S390 is special as it doesn't have IRQ lines, so these errors pop up:
drivers/built-in.o: In function 'max8903_remove':
drivers/power/max8903_charger.c:355: undefined reference to 'free_irq'
drivers/power/max8903_charger.c:357: undefined reference to 'free_irq'
drivers/power/max8903_charger.c:359: undefined reference to 'free_irq'
This commit fixes the issue by making the driver depend on
GENERIC_HARDIRQS feature.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
The ISP1704/1707 chip can be put to full power down
state by asserting the CHIP_SEL line. This patch enables
platform or board specific hooks to put the device into
power down mode in case not needed.
This patch is a preparation for enabling this powering
routine in n900 (rx-51) devices.
Thanks to Heikki Krogerus for helping out with the patch.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@nokia.com>
Acked-By: Heikki Krogerus <heikki.krogerus@nokia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Gpio charger should notify if the gpio state had changed
during suspend. This will send a CHANGED event each time
the system resumes, ensuring a plug/unplug of the charger
is not missed.
Signed-off-by: Benson Leung <bleung@chromium.org>
Acked-By: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
MAX8903 is an integrated battery charger and selector with two
power inputs (USB and AC adapter). This driver enables the charger,
handles interrupts, and provides power-supply-class information to
userland.
Tested on Exynos4 NURI / S5PC210 SLP7 boards.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
* git://git.infradead.org/battery-2.6: (30 commits)
bq20z75: Fix time and temp units
bq20z75: Fix issues with present and suspend
z2_battery: Fix count of properties
s3c_adc_battery: Fix method names when PM not set
z2_battery: Add MODULE_DEVICE_TABLE
ds2782_battery: Add MODULE_DEVICE_TABLE
bq20z75: Add MODULE_DEVICE_TABLE
power_supply: Update power_supply_is_watt_property
bq20z75: Add i2c retry mechanism
bq20z75: Add optional battery detect gpio
twl4030_charger: Make the driver atomic notifier safe
bq27x00: Use single i2c_transfer call for property read
bq27x00: Cleanup bq27x00_i2c_read
bq27x00: Minor cleanups
bq27x00: Give more specific reports on battery status
bq27x00: Add MODULE_DEVICE_TABLE
bq27x00: Add new properties
bq27x00: Poll battery state
bq27x00: Cache battery registers
bq27x00: Add bq27000 support
...
mfd_get_cell returns a const, so change the jz4740 clients to store
a const mfd cell. This silences type mismatch warnings.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
No need to explicitly set the cell's platform_data/data_size.
Modify clients to use mfd_get_cell helper function instead of
accessing platform_data directly.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Corrected temperature and time to empty/full conversions.
Temperature is in 0.1°C, time is in seconds.
Corrected units in comment. "Convert to µWh."
Signed-off-by: Benson Leung <bleung@chromium.org>
Acked-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
There are a few issues found around the battery not being present. If the
battery isn't present, then a few undesirable things happen. The first was
excessive reporting of failed properties. This was fixed by instead
returning ENODATA for all properties other than PRESENT if the battery
isn't present. That way the callers can identify the difference between a
failure and the battery not being there.
The next issue was in the suspend logic. It was found that if the battery
wasn't present, then it would return a failure, preventing the system from
going into suspend. If there is no battery present, the io is expected to
fail, so in that case, we shouldn't return the failure and just
acknowledge that it was expected.
I also found that when a gpio was used, i didn't maintain the internal
is_present state properly. I added a set of that to fix that.
Lastly, the code to see io's fail and figure out that the battery isn't
present when not using a gpio had a problem. In that code, it looked for
the read to fail and if it did, then handled it. The problem is that in
function to get the property, it first writes a value and that write can
fail, causing the code to never reach the logic after the read. Fix is
to move the logic till after the write.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
PROP_STATUS property was not counted, as result VOLTAGE_MIN property is
missing in sysfs. Fix it.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
The device table is required to load modules based on modaliases.
After adding the MODULE_DEVICE_TABLE, below entry will be added to
modules.alias:
alias i2c:aer915 z2_battery
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
The device table is required to load modules based on modaliases.
After adding the MODULE_DEVICE_TABLE, below entries will be added to
modules.alias:
alias i2c:ds2786 ds2782_battery
alias i2c:ds2782 ds2782_battery
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
The device table is required to load modules based on modaliases.
After adding the MODULE_DEVICE_TABLE, below entry will be added to
modules.alias:
alias i2c:bq20z75 bq20z75
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
With the support of platform data, now adding support for option i2c
retries on read/write failures. Ths is specified through the optional
platform data.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Adding support for an optional gpio for battery detection. This is
passed in through the i2c platform data. It also accepts another
field, battery_detect_present to signify the gpio state which means
the battery is present, either 0 (low) or 1 (high).
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
This queues work from the otg notification where the
i2c operations can be safely made. Needed for atomic otg
notifiers.
Signed-off-by: Heikki Krogerus <heikki.krogerus@nokia.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Doing this by using 2 calls sometimes results in unexpected
values being returned on OMAP3 i2c controller.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
* Consistently use uppercase for hexadecimal values.
* Clarify/fix the unit of functions return value in its comment.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
The current code only reports whether the battery is charging or
discharging. But the battery also reports whether it is fully charged,
furthermore by look at if the battery is supplied we can tell whether it
is discharging or not charging.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Jiri Kosina
Anton Vorontsov
Kalle Jokiniemi
Benson Leung
MyungJoo Ham
Justin P. Mattock
Thomas Gleixner
Linus Torvalds
Andres Salomon
Rhyland Klein
Vasily Khoruzhick
Heiko Stuebner
Axel Lin
Heikki Krogerus
Grazvydas Ignotas
Lars-Peter Clausen
Pali Rohár