- Enable msi-x link interrupts because the timer based scheduler was getting
cancelled causing the link state to be lost with repetitive card up/downs
when changing the mtu.
- Unmask mac_rmac_link interrupts only for Xframe I and prevent a spurious
link interrupt in Xframe II.
- Stop the tx queue and indicate link down when card is down
Signed-off-by: Santosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
s2io has IOMMU overflow checking, but unfortunately it is wrong.
It didn't use the standard macros, which meant that it only worked
on POWER and SPARC because only those define DMA_ERROR_CODE. Convert it to
use the standard macros instead.
I also commented two more bugs in the IOMMU handling. It assumes
that 0 DMA addresses cannot happen, but that's not true in all IOMMU setups.
The information if a buffer has been already mapped needs to be stored
elsewhere.
Didn't fix those because it needs careful checking of the buffer handling
by the maintainers.
Cc: ram.vepa@neterion.com
Cc: santosh.rastapur@neterion.com
Cc: sivakumar.subramani@neterion.com
Cc: sreenivasa.honnur@neterion.com
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
- Move all the transmit completions to a single msi-x (alarm) vector.
- Enable the continuous timer interrupt for only one transmit fifo.
Signed-off-by: Santosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
- Seperate ring specific data
- Initialize all configured rings with equal priority.
- Updated boundary check for number of Rings.
- Updated per ring statistics of rx_bytes and rx_packets.
- Moved lro struct from struct s2io_nic to struct ring_info.
- Access respective rx ring directly in fill_rx_buffers.
- Moved rx_bufs_left struct s2io_nic to struct ring_info.
- Added per ring variables - rxd_mode, rxd_count, dev, pdev.
Signed-off-by: Surjit Reang <surjit.reang@neterion.com>
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
- Removed receive buffer replenishment tasklet s2io_tasklet and instead
allocating the receive buffers in either the interrupt handler (no napi)
or the napi handler (napi enabled).
Signed-off-by: Surjit Reang <surjit.reang@neterion.com>
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
- Resubmit #3
- Added s2io_vlan_rx_kill_vid entry point function for unregistering vlan.
- Fix to aggregate vlan packets. IP offset is incremented by
4 bytes if the packet contains vlan header.
Signed-off-by: Surjit Reang <surjit.reang@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Resubmit #2
- Transmit fifo selection based on TCP/UDP ports.
- Added tx_steering_type loadable parameter for transmit fifo selection.
0x0 NO_STEERING: Default FIFO is selected.
0x1 TX_PRIORITY_STEERING: FIFO is selected based on skb->priority.
0x2 TX_DEFAULT_STEERING: FIFO is selected based on L4 Ports.
Signed-off-by: Surjit Reang <surjit.reang@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Resubmit #3
Multiqueue netwrok device support implementation.
- Added a loadable parameter "multiq" to enable/disable multiqueue support,
by default it is disabled.
- skb->queue_mapping is not used for queue/fifo selection. FIFO selection is
based on skb->priority.
- Added per FIFO flags FIFO_QUEUE_START and FIFO_QUEUE_STOP. Check this flag
for starting and stopping netif queue and update the flags accordingly.
- In tx_intr_handler added a check to ensure that we have free TXDs before wak-
ing up the queue.
- Added helper functions for queue manipulation(start/stop/wakeup) to invoke
appropriate netif_ functions.
- Calling netif_start/stop for link up/down case respectively.
- As per Andi kleen's review comments, using skb->priority field for FIFO
selection.
Signed-off-by: Surjit Reang <surjit.reang@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Resubmitting patch from Al Viro <viro@zeniv.linux.org.uk>, with subject -
[PATCH] s2io LRO bugs.
a) initiate_new_session() sets ->tcp_ack to ntohl(...); everything
else stores and expects to find there the net-endian value.
b) check for monotonic timestamps in verify_l3_l4_lro_capable()
compares the value sitting in TCP option (right there in the skb->data,
net-endian 32bit) with the value picked from earlier packet.
Doing that without ntohl() is an interesting idea and it might even
work occasionally; unfortunately, it's quite broken.
Signed-off-by: Surjit Reang <surjit.reang@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes to enable multiple transmit fifos (upto a maximum of eight).
- Moved single tx_lock from struct s2io_nic to struct fifo_info.
- Moved single ufo_in_band_v structure from struct s2io_nic to struct
fifo_info.
- Assign the respective interrupt number for the transmitting fifo in the
transmit descriptor (TXD).
- Added boundary checks for number of FIFOs enabled and FIFO length.
Signed-off-by: Surjit Reang <surjit.reang@neterion.com>
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Support to add/delete/store/restore 64 and 128 Ethernet addresses for Xframe I and Xframe II respectively.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Added set_mac_address driver entry point
- Copying permanent mac address to dev->perm_addr
- Incorporated following review comments from Jeff
- Converted the macro to a function and removed call to memset
- regarding function naming convention, for all callbacks and entry points
will have 's2io_' prefix and helper functions will have 'do_s2io_' prefix.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Code Optimization of s2io_isr function.
- Isr check using per device napi variable instead of driver global.
- Reduced from 3 to 1 if condition before check for processing packet receive
packets.
- Implemented Jeff's comment to use synchronize_irq. Removed the isr_cnt
variable as it became redundant.
- One time de assert the interrupts by writing all F's to the general_int_mask
register instead of de asserting by clearing the source of interrupts with
multiple writes which causes loss of interrupts (race conditions). It is
entirely possible that before the driver has a chance to mask the asserted
alarm bit, another alarm/traffic interrupt bit gets asserted as well. In
this case Herc will keep the INTA line asserted and the bridge will not
send a new Assert_INTA message upstream.
[ Resolved conflicts due to napi_struct changes... -DaveM ]
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Santosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Added check to return from the traffic handling function, if the card status
is DOWN.
- Implemented Jeff's comments on incorrect return value in s2io_poll function.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Santosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Added support to poll entire set of device errors and alarams.
- A note on how device errors and alarms are handled:
- The adapter will automatically recover from uncorrectable ECC errors.
Packets containing corrupted data will be dropped (not transmitted) or tagged
as invalid before being passed to the host.
- The adapter cannot recover from any internal state machine errors. A state
machine error requires a device reset.
- Any internal error that could potentially result in .store trampling.
(undesirable PCI behaviour)is tagged as a "serious error". In such cases
the adapter will give up its ability to be a bus master. In this situation
the host will still be able to read internal device registers in order to
generate an error report. A device reset is necessary to return to normal
operation.
- In the event of a pcix data parity error, the adapter will automatically
disable itself. Adapter_En will automatically transition from '1' to '0' and
the adapter will enter its clean-up routine. Once the device has achieved
quiescence, an adapter reset should be performed.
- Replaced alarm_intr_handler() with s2io_handle_errors().
- Added statistic counters to monitor the alarms.
[ Fix warnings wrt. do_s2io_chk_alarm_bit(), Callers pass in an
"unsigned long long *" but the function takes a "u64 *" which is
different on many 64-bit platforms. -DaveM ]
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Santosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Added support to unmask entire set of device errors and alarams.
Alarm interrupts are generated for a myriad of purposes, ranging from
illegal operations or requests to internal state machine errors and
uncorrectable data corruption errors. In several cases the adapter can
recover gracefully from unexpected events; however, in some cases, a device
reset may be necessary. This patch handles alarms generated by all the
blocks within the device.
The adapter generates the following types of alarms:
1. Link state transitions (local/remote fault) or other link-related
problems.
2. Problems with any device peripherals, including the EEPROM, FLASH,
etc.
3. Correctable ECC errors (single-bit errors) on internal data
structures or frame data.
4. Uncorrectable ECC errors (multi-bit errors) on internal data
structures or frame data.
5. State machine errors, which indicate that internal control
structures have become corrupted.
6. PCI related errors, including parity errors or illegal transactions.
7. Other unexpected events.
- Implemented Jeff's review comments to use do_s2io_write_bits function to avoid
duplicate codes.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Santosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Calling store_xmsi_data to store the MSI-X datas during initialization
in s2io-init_nic function
- Disabling NAPI when MSI-X is enabled
- Freeing sp->entries and sp->s2io_entries in s2io_rem_isr
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Sreenivasa Honnur
David S. Miller
Andi Kleen
Jeff Garzik
Surjit Reang
Jiri Slaby
Sivakumar Subramani