Pull sparc fixes from David Miller:
"Just some small fixes here and there, and a refcount leak in a serial
driver, nothing serious"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
serial/sunsu: fix refcount leak
sparc: Set "ARCH: sunxx" information on the same line
sparc: vdso: Drop implicit common-page-size linker flag
The function of_find_node_by_path() acquires a reference to the node
returned by it and that reference needs to be dropped by its caller.
su_get_type() doesn't do that. The match node are used as an identifier
to compare against the current node, so we can directly drop the refcount
after getting the node from the path as it is not used as pointer.
Fix this by use a single variable and drop the refcount right after
of_find_node_by_path().
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f6aa5beb45 ("serial: 8250: Fix clearing FIFOs in RS485 mode
again") makes a change to FIFO clearing code which its commit message
suggests was intended to be specific to use with RS485 mode, however:
1) The change made does not just affect __do_stop_tx_rs485(), it also
affects other uses of serial8250_clear_fifos() including paths for
starting up, shutting down or auto-configuring a port regardless of
whether it's an RS485 port or not.
2) It makes the assumption that resetting the FIFOs is a no-op when
FIFOs are disabled, and as such it checks for this case & explicitly
avoids setting the FIFO reset bits when the FIFO enable bit is
clear. A reading of the PC16550D manual would suggest that this is
OK since the FIFO should automatically be reset if it is later
enabled, but we support many 16550-compatible devices and have never
required this auto-reset behaviour for at least the whole git era.
Starting to rely on it now seems risky, offers no benefit, and
indeed breaks at least the Ingenic JZ4780's UARTs which reads
garbage when the RX FIFO is enabled if we don't explicitly reset it.
3) By only resetting the FIFOs if they're enabled, the behaviour of
serial8250_do_startup() during boot now depends on what the value of
FCR is before the 8250 driver is probed. This in itself seems
questionable and leaves us with FCR=0 & no FIFO reset if the UART
was used by 8250_early, otherwise it depends upon what the
bootloader left behind.
4) Although the naming of serial8250_clear_fifos() may be unclear, it
is clear that callers of it expect that it will disable FIFOs. Both
serial8250_do_startup() & serial8250_do_shutdown() contain comments
to that effect, and other callers explicitly re-enable the FIFOs
after calling serial8250_clear_fifos(). The premise of that patch
that disabling the FIFOs is incorrect therefore seems wrong.
For these reasons, this reverts commit f6aa5beb45 ("serial: 8250: Fix
clearing FIFOs in RS485 mode again").
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: f6aa5beb45 ("serial: 8250: Fix clearing FIFOs in RS485 mode again").
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Daniel Jedrychowski <avistel@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: linux-mips@vger.kernel.org
Cc: linux-serial@vger.kernel.org
Cc: stable <stable@vger.kernel.org> # 4.10+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull tty driver fixes from Greg KH:
"Here are three small tty driver fixes for 4.20-rc6
Nothing major, just some bug fixes for reported issues. Full details
are in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
kgdboc: fix KASAN global-out-of-bounds bug in param_set_kgdboc_var()
tty: serial: 8250_mtk: always resume the device in probe.
tty: do not set TTY_IO_ERROR flag if console port
Pull USB fixes from Greg KH:
"Here are some small USB fixes for 4.20-rc6
The "largest" here are some xhci fixes for reported issues. Also here
is a USB core fix, some quirk additions, and a usb-serial fix which
required the export of one of the tty layer's functions to prevent
code duplication. The tty maintainer agreed with this change.
All of these have been in linux-next with no reported issues"
* tag 'usb-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
xhci: Prevent U1/U2 link pm states if exit latency is too long
xhci: workaround CSS timeout on AMD SNPS 3.0 xHC
USB: check usb_get_extra_descriptor for proper size
USB: serial: console: fix reported terminal settings
usb: quirk: add no-LPM quirk on SanDisk Ultra Flair device
USB: Fix invalid-free bug in port_over_current_notify()
usb: appledisplay: Add 27" Apple Cinema Display
This patch is trying to fix KE issue due to
"BUG: KASAN: global-out-of-bounds in param_set_kgdboc_var+0x194/0x198"
reported by Syzkaller scan."
[26364:syz-executor0][name:report8t]BUG: KASAN: global-out-of-bounds in param_set_kgdboc_var+0x194/0x198
[26364:syz-executor0][name:report&]Read of size 1 at addr ffffff900e44f95f by task syz-executor0/26364
[26364:syz-executor0][name:report&]
[26364:syz-executor0]CPU: 7 PID: 26364 Comm: syz-executor0 Tainted: G W 0
[26364:syz-executor0]Call trace:
[26364:syz-executor0][<ffffff9008095cf8>] dump_bacIctrace+Ox0/0x470
[26364:syz-executor0][<ffffff9008096de0>] show_stack+0x20/0x30
[26364:syz-executor0][<ffffff90089cc9c8>] dump_stack+Oxd8/0x128
[26364:syz-executor0][<ffffff90084edb38>] print_address_description +0x80/0x4a8
[26364:syz-executor0][<ffffff90084ee270>] kasan_report+Ox178/0x390
[26364:syz-executor0][<ffffff90084ee4a0>] _asan_report_loadi_noabort+Ox18/0x20
[26364:syz-executor0][<ffffff9008b092ac>] param_set_kgdboc_var+Ox194/0x198
[26364:syz-executor0][<ffffff900813af64>] param_attr_store+Ox14c/0x270
[26364:syz-executor0][<ffffff90081394c8>] module_attr_store+0x60/0x90
[26364:syz-executor0][<ffffff90086690c0>] sysfs_kl_write+Ox100/0x158
[26364:syz-executor0][<ffffff9008666d84>] kernfs_fop_write+0x27c/0x3a8
[26364:syz-executor0][<ffffff9008508264>] do_loop_readv_writev+0x114/0x1b0
[26364:syz-executor0][<ffffff9008509ac8>] do_readv_writev+0x4f8/0x5e0
[26364:syz-executor0][<ffffff9008509ce4>] vfs_writev+0x7c/Oxb8
[26364:syz-executor0][<ffffff900850ba64>] SyS_writev+Oxcc/0x208
[26364:syz-executor0][<ffffff90080883f0>] elO_svc_naked +0x24/0x28
[26364:syz-executor0][name:report&]
[26364:syz-executor0][name:report&]The buggy address belongs to the variable:
[26364:syz-executor0][name:report&] kgdb_tty_line+Ox3f/0x40
[26364:syz-executor0][name:report&]
[26364:syz-executor0][name:report&]Memory state around the buggy address:
[26364:syz-executor0] ffffff900e44f800: 00 00 00 00 00 04 fa fa fa fa fa fa 00 fa fa fa
[26364:syz-executor0] ffffff900e44f880: fa fa fa fa 00 fa fa fa fa fa fa fa 00 fa fa fa
[26364:syz-executor0]> ffffff900e44f900: fa fa fa fa 04 fa fa fa fa fa fa fa 00 00 00 00
[26364:syz-executor0][name:report&] ^
[26364:syz-executor0] ffffff900e44f980: 00 fa fa fa fa fa fa fa 04 fa fa fa fa fa fa fa
[26364:syz-executor0] ffffff900e44fa00: 04 fa fa fa fa fa fa fa 00 fa fa fa fa fa fa fa
[26364:syz-executor0][name:report&]
[26364:syz-executor0][name:panic&]Disabling lock debugging due to kernel taint
[26364:syz-executor0]------------[cut here]------------
After checking the source code, we've found there might be an out-of-bounds
access to "config[len - 1]" array when the variable "len" is zero.
Signed-off-by: Macpaul Lin <macpaul@gmail.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_register_8250_port calls uart_config_port, which calls
config_port on the port before it tries to power on the port. So we need
the port to be on before calling serial8250_register_8250_port. Change
the code to always do a runtime resume in probe before registering port,
and always do a runtime suspend in remove.
This basically reverts the change in commit 68e5fc4a25 ("tty: serial:
8250_mtk: use pm_runtime callbacks for enabling"), but still use
pm_runtime callbacks.
Fixes: 68e5fc4a25 ("tty: serial: 8250_mtk: use pm_runtime callbacks for enabling")
Signed-off-by: Peter Shih <pihsun@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB-serial console implementation has never reported the actual
terminal settings used. Despite storing the corresponding cflags in its
struct console, these were never honoured on later tty open() where the
tty termios would be left initialised to the driver defaults.
Unlike the serial console implementation, the USB-serial code calls
subdriver open() already at console setup. While calling set_termios()
and write() before open() looks like it could work for some USB-serial
drivers, others definitely do not expect this, so modelling this after
serial core is going to be intrusive, if at all possible.
Instead, use a (renamed) tty helper to save the termios data used at
console setup so that the tty termios reflects the actual terminal
settings after a subsequent tty open().
Note that the calls to tty_init_termios() (tty_driver_install()) and
tty_save_termios() are serialised using the disconnect mutex.
This specifically fixes a regression that was triggered by a recent
change adding software flow control to the pl2303 driver: a getty trying
to disable flow control while leaving the baud rate unchanged would now
also set the baud rate to the driver default (prior to the flow-control
change this had been a noop).
Fixes: 7041d9c3f0 ("USB: serial: pl2303: add support for tx xon/xoff flow control")
Cc: stable <stable@vger.kernel.org> # 4.18
Cc: Florian Zumbiehl <florz@florz.de>
Reported-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
of_find_node_by_path() acquires a reference to the node
returned by it and that reference needs to be dropped by its caller.
This place is not doing this, so fix it.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since Commit 761ed4a945 ('tty: serial_core: convert uart_close to use
tty_port_close') and Commit 4dda864d73 ('tty: serial_core: Fix serial
console crash on port shutdown), a serial port which is used as
console can be stuck when logging out if there is a remained process.
After logged out, agetty will try to grab the serial port but it will
be failed because the previous process did not release the port
correctly. To fix this, TTY_IO_ERROR bit should not be enabled of
tty_port_close if the port is console port.
Reproduce step:
- Run background processes from serial console
$ while true; do sleep 10; done &
- Log out
$ logout
-> Stuck
- Read journal log by journalctl | tail
Jan 28 16:07:01 ubuntu systemd[1]: Stopped Serial Getty on ttyAMA0.
Jan 28 16:07:01 ubuntu systemd[1]: Started Serial Getty on ttyAMA0.
Jan 28 16:07:02 ubuntu agetty[1643]: /dev/ttyAMA0: not a tty
Fixes: 761ed4a945 ("tty: serial_core: convert uart_close to use tty_port_close")
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Rob Herring <robh@kernel.org>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Chanho Park <parkch98@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull tty/serial fixes from Greg KH:
"Here are some small tty fixes for 4.20-rc2
One of these missed the original 4.19-final release, I missed that I
hadn't done a pull request for it as it was in linux-next and my
branch for a long time, that's my fault.
The others are small, fixing some reported issues and finally fixing
the termios mess for alpha so that glibc has a chance to implement
some missing functionality that has been pending for many years now.
All of these have been in linux-next with no reported issues"
* tag 'tty-4.20-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: sh-sci: Fix could not remove dev_attr_rx_fifo_timeout
arch/alpha, termios: implement BOTHER, IBSHIFT and termios2
termios, tty/tty_baudrate.c: fix buffer overrun
vt: fix broken display when running aptitude
serial: sh-sci: Fix receive on SCIFA/SCIFB variants with DMA
If you run aptitude on framebuffer console, the display is corrupted. The
corruption is caused by the commit d8ae7242. The patch adds "offset" to
"start" when calling scr_memsetw, but it forgets to do the same addition
on a subsequent call to do_update_region.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Fixes: d8ae724271 ("vt: preserve unicode values corresponding to screen characters")
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@vger.kernel.org # 4.19
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull tty/serial updates from Greg KH:
"Here is the big tty and serial pull request for 4.20-rc1
Lots of little things here, including a merge from the SPI tree in
order to keep things simpler for everyone to sync around for one
platform.
Major stuff is:
- tty buffer clearing after use
- atmel_serial fixes and additions
- xilinx uart driver updates
and of course, lots of tiny fixes and additions to individual serial
drivers.
All of these have been in linux-next with no reported issues for a
while"
* tag 'tty-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (66 commits)
of: base: Change logic in of_alias_get_alias_list()
of: base: Fix english spelling in of_alias_get_alias_list()
serial: sh-sci: do not warn if DMA transfers are not supported
serial: uartps: Do not allow use aliases >= MAX_UART_INSTANCES
tty: check name length in tty_find_polling_driver()
serial: sh-sci: Add r8a77990 support
tty: wipe buffer if not echoing data
tty: wipe buffer.
serial: fsl_lpuart: Remove the alias node dependence
TTY: sn_console: Replace spin_is_locked() with spin_trylock()
Revert "serial:serial_core: Allow use of CTS for PPS line discipline"
serial: 8250_uniphier: add auto-flow-control support
serial: 8250_uniphier: flatten probe function
serial: 8250_uniphier: remove unused "fifo-size" property
dt-bindings: serial: sh-sci: Document r8a7744 bindings
serial: uartps: Fix missing unlock on error in cdns_get_id()
tty/serial: atmel: add ISO7816 support
tty/serial_core: add ISO7816 infrastructure
serial:serial_core: Allow use of CTS for PPS line discipline
serial: docs: Fix filename for serial reference implementation
...
Pull drm updates from Dave Airlie:
"This is going to rebuild more than drm as it adds a new helper to
list.h for doing bulk updates. Seemed like a reasonable addition to
me.
Otherwise the usual merge window stuff lots of i915 and amdgpu, not so
much nouveau, and piles of everything else.
Core:
- Adds a new list.h helper for doing bulk list updates for TTM.
- Don't leak fb address in smem_start to userspace (comes with EXPORT
workaround for people using mali out of tree hacks)
- udmabuf device to turn memfd regions into dma-buf
- Per-plane blend mode property
- ref/unref replacements with get/put
- fbdev conflicting framebuffers code cleaned up
- host-endian format variants
- panel orientation quirk for Acer One 10
bridge:
- TI SN65DSI86 chip support
vkms:
- GEM support.
- Cursor support
amdgpu:
- Merge amdkfd and amdgpu into one module
- CEC over DP AUX support
- Picasso APU support + VCN dynamic powergating
- Raven2 APU support
- Vega20 enablement + kfd support
- ACP powergating improvements
- ABGR/XBGR display support
- VCN jpeg support
- xGMI support
- DC i2c/aux cleanup
- Ycbcr 4:2:0 support
- GPUVM improvements
- Powerplay and powerplay endian fixes
- Display underflow fixes
vmwgfx:
- Move vmwgfx specific TTM code to vmwgfx
- Split out vmwgfx buffer/resource validation code
- Atomic operation rework
bochs:
- use more helpers
- format/byteorder improvements
qxl:
- use more helpers
i915:
- GGTT coherency getparam
- Turn off resource streamer API
- More Icelake enablement + DMC firmware
- Full PPGTT for Ivybridge, Haswell and Valleyview
- DDB distribution based on resolution
- Limited range DP display support
nouveau:
- CEC over DP AUX support
- Initial HDMI 2.0 support
virtio-gpu:
- vmap support for PRIME objects
tegra:
- Initial Tegra194 support
- DMA/IOMMU integration fixes
msm:
- a6xx perf improvements + clock prefix
- GPU preemption optimisations
- a6xx devfreq support
- cursor support
rockchip:
- PX30 support
- rgb output interface support
mediatek:
- HDMI output support on mt2701 and mt7623
rcar-du:
- Interlaced modes on Gen3
- LVDS on R8A77980
- D3 and E3 SoC support
hisilicon:
- misc fixes
mxsfb:
- runtime pm support
sun4i:
- R40 TCON support
- Allwinner A64 support
- R40 HDMI support
omapdrm:
- Driver rework changing display pipeline ordering to use common code
- DMM memory barrier and irq fixes
- Errata workarounds
exynos:
- out-bridge support for LVDS bridge driver
- Samsung 16x16 tiled format support
- Plane alpha and pixel blend mode support
tilcdc:
- suspend/resume update
mali-dp:
- misc updates"
* tag 'drm-next-2018-10-24' of git://anongit.freedesktop.org/drm/drm: (1382 commits)
firmware/dmc/icl: Add missing MODULE_FIRMWARE() for Icelake.
drm/i915/icl: Fix signal_levels
drm/i915/icl: Fix DDI/TC port clk_off bits
drm/i915/icl: create function to identify combophy port
drm/i915/gen9+: Fix initial readout for Y tiled framebuffers
drm/i915: Large page offsets for pread/pwrite
drm/i915/selftests: Disable shrinker across mmap-exhaustion
drm/i915/dp: Link train Fallback on eDP only if fallback link BW can fit panel's native mode
drm/i915: Fix intel_dp_mst_best_encoder()
drm/i915: Skip vcpi allocation for MSTB ports that are gone
drm/i915: Don't unset intel_connector->mst_port
drm/i915: Only reset seqno if actually idle
drm/i915: Use the correct crtc when sanitizing plane mapping
drm/i915: Restore vblank interrupts earlier
drm/i915: Check fb stride against plane max stride
drm/amdgpu/vcn:Fix uninitialized symbol error
drm: panel-orientation-quirks: Add quirk for Acer One 10 (S1003)
drm/amd/amdgpu: Fix debugfs error handling
drm/amdgpu: Update gc_9_0 golden settings.
drm/amd/powerplay: update PPtable with DC BTC and Tvr SocLimit fields
...
Pull tty ioctl updates from Al Viro:
"This is the compat_ioctl work related to tty ioctls.
Quite a bit of dead code taken out, all tty-related stuff gone from
fs/compat_ioctl.c. A bunch of compat bugs fixed - some still remain,
but all more or less generic tty-related ioctls should be covered
(remaining issues are in things like driver-private ioctls in a pcmcia
serial card driver not getting properly handled in 32bit processes on
64bit host, etc)"
* 'work.tty-ioctl' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (53 commits)
kill TIOCSERGSTRUCT
change semantics of ldisc ->compat_ioctl()
kill TIOCSER[SG]WILD
synclink_gt(): fix compat_ioctl()
pty: fix compat ioctls
compat_ioctl - kill keyboard ioctl handling
gigaset: add ->compat_ioctl()
vt_compat_ioctl(): clean up, use compat_ptr() properly
gigaset: don't try to printk userland buffer contents
dgnc: don't bother with (empty) stub for TCXONC
dgnc: leave TIOC[GS]SOFTCAR to ldisc
remove fallback to drivers for TIOCGICOUNT
dgnc: break-related ioctls won't reach ->ioctl()
kill the rest of tty COMPAT_IOCTL() entries
dgnc: TIOCM... won't reach ->ioctl()
isdn_tty: TCSBRK{,P} won't reach ->ioctl()
kill capinc_tty_ioctl()
take compat TIOC[SG]SERIAL treatment into tty_compat_ioctl()
synclink: reduce pointless checks in ->ioctl()
complete ->[sg]et_serial() switchover
...
Pull siginfo updates from Eric Biederman:
"I have been slowly sorting out siginfo and this is the culmination of
that work.
The primary result is in several ways the signal infrastructure has
been made less error prone. The code has been updated so that manually
specifying SEND_SIG_FORCED is never necessary. The conversion to the
new siginfo sending functions is now complete, which makes it
difficult to send a signal without filling in the proper siginfo
fields.
At the tail end of the patchset comes the optimization of decreasing
the size of struct siginfo in the kernel from 128 bytes to about 48
bytes on 64bit. The fundamental observation that enables this is by
definition none of the known ways to use struct siginfo uses the extra
bytes.
This comes at the cost of a small user space observable difference.
For the rare case of siginfo being injected into the kernel only what
can be copied into kernel_siginfo is delivered to the destination, the
rest of the bytes are set to 0. For cases where the signal and the
si_code are known this is safe, because we know those bytes are not
used. For cases where the signal and si_code combination is unknown
the bits that won't fit into struct kernel_siginfo are tested to
verify they are zero, and the send fails if they are not.
I made an extensive search through userspace code and I could not find
anything that would break because of the above change. If it turns out
I did break something it will take just the revert of a single change
to restore kernel_siginfo to the same size as userspace siginfo.
Testing did reveal dependencies on preferring the signo passed to
sigqueueinfo over si->signo, so bit the bullet and added the
complexity necessary to handle that case.
Testing also revealed bad things can happen if a negative signal
number is passed into the system calls. Something no sane application
will do but something a malicious program or a fuzzer might do. So I
have fixed the code that performs the bounds checks to ensure negative
signal numbers are handled"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (80 commits)
signal: Guard against negative signal numbers in copy_siginfo_from_user32
signal: Guard against negative signal numbers in copy_siginfo_from_user
signal: In sigqueueinfo prefer sig not si_signo
signal: Use a smaller struct siginfo in the kernel
signal: Distinguish between kernel_siginfo and siginfo
signal: Introduce copy_siginfo_from_user and use it's return value
signal: Remove the need for __ARCH_SI_PREABLE_SIZE and SI_PAD_SIZE
signal: Fail sigqueueinfo if si_signo != sig
signal/sparc: Move EMT_TAGOVF into the generic siginfo.h
signal/unicore32: Use force_sig_fault where appropriate
signal/unicore32: Generate siginfo in ucs32_notify_die
signal/unicore32: Use send_sig_fault where appropriate
signal/arc: Use force_sig_fault where appropriate
signal/arc: Push siginfo generation into unhandled_exception
signal/ia64: Use force_sig_fault where appropriate
signal/ia64: Use the force_sig(SIGSEGV,...) in ia64_rt_sigreturn
signal/ia64: Use the generic force_sigsegv in setup_frame
signal/arm/kvm: Use send_sig_mceerr
signal/arm: Use send_sig_fault where appropriate
signal/arm: Use force_sig_fault where appropriate
...
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.20 series:
Core changes:
- A patch series from Hans Verkuil to make it possible to
enable/disable IRQs on a GPIO line at runtime and drive GPIO lines
as output without having to put/get them from scratch.
The irqchip callbacks have been improved so that they can use only
the fastpatch callbacks to enable/disable irqs like any normal
irqchip, especially the gpiod_lock_as_irq() has been improved to be
callable in fastpath context.
A bunch of rework had to be done to achieve this but it is a big
win since I never liked to restrict this to slowpath. The only call
requireing slowpath was try_module_get() and this is kept at the
.request_resources() slowpath callback. In the GPIO CEC driver this
is a big win sine a single line is used for both outgoing and
incoming traffic, and this needs to use IRQs for incoming traffic
while actively driving the line for outgoing traffic.
- Janusz Krzysztofik improved the GPIO array API to pass a "cookie"
(struct gpio_array) and a bitmap for setting or getting multiple
GPIO lines at once.
This improvement orginated in a specific need to speed up an OMAP1
driver and has led to a much better API and real performance gains
when the state of the array can be used to bypass a lot of checks
and code when we want things to go really fast.
The previous code would minimize the number of calls down to the
driver callbacks assuming the CPU speed was orders of magnitude
faster than the I/O latency, but this assumption was wrong on
several platforms: what we needed to do was to profile and improve
the speed on the hot path of the array functions and this change is
now completed.
- Clean out the painful and hard to grasp BNF experiments from the
device tree bindings. Future approaches are looking into using JSON
schema for this purpose. (Rob Herring is floating a patch series.)
New drivers:
- The RCAR driver now supports r8a774a1 (RZ/G2M).
- Synopsys GPIO via CREGs driver.
Major improvements:
- Modernization of the EP93xx driver to use irqdomain and other
contemporary concepts.
- The ingenic driver has been merged into the Ingenic pin control
driver and removed from the GPIO subsystem.
- Debounce support in the ftgpio010 driver"
* tag 'gpio-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (116 commits)
gpio: Clarify kerneldoc on gpiochip_set_chained_irqchip()
gpio: Remove unused 'irqchip' argument to gpiochip_set_cascaded_irqchip()
gpio: Drop parent irq assignment during cascade setup
mmc: pwrseq_simple: Fix incorrect handling of GPIO bitmap
gpio: fix SNPS_CREG kconfig dependency warning
gpiolib: Initialize gdev field before is used
gpio: fix kernel-doc after devres.c file rename
gpio: fix doc string for devm_gpiochip_add_data() to not talk about irq_chip
gpio: syscon: Fix possible NULL ptr usage
gpiolib: Show correct direction from the beginning
pinctrl: msm: Use init_valid_mask exported function
gpiolib: Add init_valid_mask exported function
GPIO: add single-register GPIO via CREG driver
dt-bindings: Document the Synopsys GPIO via CREG bindings
gpio: mockup: use device properties instead of platform_data
gpio: Slightly more helpful debugfs
gpio: omap: Remove set but not used variable 'dev'
gpio: omap: drop omap_gpio_list
Accept partial 'gpio-line-names' property.
gpio: omap: get rid of the conditional PM runtime calls
...
On SCIFA and SCIFB serial ports with DMA support (i.e. some ports on
R-Car Gen2 and RZ/G1 SoCs), receive DMA operations are submitted before
the DMA channel pointer is initialized. Hence this fails, and the
driver tries to fall back to PIO. However, at this early phase in the
initialization sequence, fallback to PIO does not work, leading to a
serial port that cannot receive any data.
Fix this by calling sci_submit_rx() after initialization of the DMA
channel pointer.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Fixes: 2c4ee23530 ("serial: sh-sci: Postpone DMA release when falling back to PIO")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check compatible string first before setting up bit in bitmap to also
cover cases that allocated bitfield is not big enough.
Show warning about it but let driver to continue to work with allocated
bitfield to keep at least some devices (included console which
is commonly close to serial0) to work.
Fixes: b1078c355d ("of: base: Introduce of_alias_get_alias_list() to check alias IDs")
Fixes: ae1cca3fa3 ("serial: uartps: Change uart ID port allocation")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not all (H)SCIF devices support DMA, and failure to set it up is not
normally a cause for concern. This patch demotes the associated warning to
debug output.
Inspired by BSP patch "sci: sh-sci: Fix transfer sequence of unsupport DMA
transfer" (6beb1f98d3bd30) by Hiromitsu Yamasaki.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Once upon a time a bunch of serial drivers used to provide that;
today it's only amiserial and it's FUBAR - the structure being
copied to userland includes kernel pointers, fields with
config-dependent size, etc. No userland code using it could
possibly survive - e.g. enabling lockdep definitely changes the
layout. Besides, it's a massive infoleak.
Kill it. If somebody needs that data for debugging purposes, they
can bloody well expose it saner ways. Assuming anyone does debugging
of amiserial in the first place, that is.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Linus Torvalds
Yangtao Li
Paul Burton
Macpaul Lin
Peter Shih
Johan Hovold
Chanho Park
Yoshihiro Shimoda
H. Peter Anvin
Mikulas Patocka
Mike Rapoport
Geert Uytterhoeven
Michal Simek
Ulrich Hecht
Al Viro