Move the checking of the LOG_DEVICE into a function to reduce the
number of #ifdefs and ensure more of the code gets compiled/checked,
and make it easier to change this for internal debugging purposes
(such as checking >1 device).
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regmap API had a noinc_read function added for instances where devices
supported returning data from an internal FIFO in a single read.
This commit adds the noinc_write variant to allow writing to a non
incrementing register, this is used in devices such as the sx1301 for
loading firmware.
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Split regmap_config.use_single_rw into use_single_read and
use_single_write. This change enables drivers of devices which only
support bulk operations in one direction to use the regmap_bulk_*()
functions for both directions and have their bulk operation split into
single operations only when necessary.
Update all struct regmap_config instances where use_single_rw==true to
instead set both use_single_read and use_single_write. No attempt was
made to evaluate whether it is possible to set only one of
use_single_read or use_single_write.
Signed-off-by: David Frey <dpfrey@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
regmap: Support non-incrementing registers
Some devices have individual registers that don't autoincrement the
register address during bulk reads but instead repeatedly read the same
value, for example for monitoring GPIOs or ADCs. Add support for these.
The regmap API usually assumes that bulk read operations will read a
range of registers but some I2C/SPI devices have certain registers for
which a such a read operation will return data from an internal FIFO
instead. Add an explicit API to support bulk read without range semantics.
Some linux drivers use regmap_bulk_read or regmap_raw_read for such
registers, for example mpu6050 or bmi150 from IIO. This only happens to
work because when caching is disabled a single regmap read op will map
to a single bus read op (as desired). This breaks if caching is enabled and
reg+1 happens to be a cacheable register.
Without regmap support refactoring a driver to enable regmap caching
requires separate I2C and SPI paths. This is exactly what regmap is
supposed to help avoid.
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds Serial Camera Control Bus (SCCB) support for regmap API that
is intended to be used by some of Omnivision sensor drivers.
The ov772x and ov9650 drivers are going to use this SCCB regmap API.
The ov772x driver was previously only worked with the i2c controller
drivers that support I2C_FUNC_PROTOCOL_MANGLING, because the ov772x
device doesn't support repeated starts. After commit 0b964d183c
("media: ov772x: allow i2c controllers without
I2C_FUNC_PROTOCOL_MANGLING"), reading ov772x register is replaced with
issuing two separated i2c messages in order to avoid repeated start.
Using this SCCB regmap hides the implementation detail.
The ov9650 driver also issues two separated i2c messages to read the
registers as the device doesn't support repeated start. So it can
make use of this SCCB regmap.
Cc: Mark Brown <broonie@kernel.org>
Cc: Peter Rosin <peda@axentia.se>
Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Jacopo Mondi <jacopo+renesas@jmondi.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SLIMbus supports upto 16 bytes in value management messages,
so add support to read/writes upto 16 bytes.
This also removes redundant single register reg_read/reg_write.
Also useful for paged register access on SLIMbus interfaced codecs.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
As per SLIMBus specs Value Elements and Information Elements
address map ranges from 0x000 - 0xFFF.
So allow register addresses up to 16 bits
Fixes: 7d6f7fb053 ("regmap: add SLIMbus support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Capability to attach an existing clk to a MMIO regmap was
introduced in 4.17rc1.
However, when using attached clk, regmap does not do the clk_get.
Therefore it should not do the clk_put when freeing the MMIO
regmap context.
There does not appear to be any users of attached clocks yet
so this would be a good time to make this change before anything
depends on the existing behaviour.
Signed-off-by: James Kelly <jamespeterkelly@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently when debugfs_create_dir() fails we receive a warning message
that provides no indication as to what was the directory entry that
failed to be created.
Improve the warning message by printing the directory name that failed
in order to help debugging.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Free map->debugfs_name when debugfs_create_dir() failed to avoid memory
leak.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When allocating dummy names we need to store a pointer to the string we
allocate so that we don't leak it on free.
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit 9b947a13e7 ("regmap: use debugfs even when no device")
allows the usage of regmap debugfs even when there is no device
associated, which causes several warnings like this:
(NULL device *): Failed to create debugfs directory
This happens when the debugfs file name is 'dummy'.
The first dummy debugfs creation works fine, but subsequent creations
fail as they have all the same name.
Disambiguate the 'dummy' debugfs file name by adding a suffix entry,
so that the names become dummy0, dummy1, dummy2, etc.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
regmap_init_mmio_clk allows to specify a clock that needs to be enabled
while accessing the registers.
However, that clock is retrieved through its clock ID, which means it will
lookup that clock based on the current device that registers the regmap,
and, in the DT case, will only look in that device OF node.
This might be problematic if the clock to enable is stored in another node.
Let's add a function that allows to attach a clock that has already been
retrieved to a regmap in order to fix this.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The handling for the first two cases in regmap_bulk_write is
essentially identical. The first case is just a better implementation of
the second, supporting 8 byte registers and doing the locking manually to
avoid bouncing the lock for each register. Drop some redundant code by
removing the second of these cases and allowing both situations to be
handled by the same code.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Raw writes may need to be split into small chunks if max_raw_write is
set. Tidy up the code implementing this, the new code is slightly
clearer, slightly shorter and slightly more efficient.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown
Ben Dooks
Ben Whitten
David Frey
Crestez Dan Leonard
Akinobu Mita
Srinivas Kandagatla
James Kelly
Fabio Estevam
Jeffy Chen
Maxime Ripard
Charles Keepax